Stihl 1124 · Section G · 7 of 15 · 31 parts
Ignition system
Fits 084.
Historical fitment & changes (4) — includes parts and conditions not shown on this drawing.
Parts (31)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 1124 400 1203 | Flywheel Fitment / change note → | 1 |
| 2 | 1124 400 1207 | Flywheel Fitment / change note → | 1 |
| 3 | 1124 404 3500 | Generator | 1 |
| 4 | 1118 431 6600 NLA | Terminal pin no longer available from factory | 1 |
| 5 | 9041 319 0660 | Pan head screw M4x12 | 3 |
| 6 | 1121 405 1900 NLA | Support | 1 |
| 7 | 9211 260 1340 | Hexagon nut M10x1 | 1 |
| 8 | 1124 400 1308 | Ignition module EY-V Fitment / change note → | 1 |
| 9 | not sold separately | Ignition lead 200 mm not available as a separate item | 1 |
| 10 | 0000 989 1010 | Grommet | 1 |
| 11 | 0000 448 1250 | Lead retainer | 1 |
| 12 | 1122 448 1200 NLA | Lead retainer Fitment / change note → | 1 |
| 13 | 1118 400 1001 | Trigger unit | 1 |
| 14 | 9041 216 0300 | Pan head screw M3x4 | 1 |
| 15 | 1124 440 1101 | Short circuit wire → replaced by 1124 440 3000 TI 9/2009 | 1 |
| 16 | 1110 442 7000 NLA | Contact sleeve no longer available from factory | 1 |
| 17 | 0751 030 8953 NLA | Terminal socket 4.8-1 no longer available from factory | 1 |
| 18 | 1124 440 2200 | Ground wire | 1 |
| 19 | 0751 030 8969 | Terminal socket A5-1.5 no longer available from factory | 1 |
| 20 | 1124 440 2210 | Ground wire | 1 |
| 21 | 0751 030 8963 | Terminal socket 12-1 no longer available from factory | 1 |
| 22 | 1124 405 8000 | Insulating hose 110 mm / 4.3'' | 1 |
| 23 | 9291 021 0120 | Washer 5.3 Fitment / change note → | 3 |
| 24 | 9022 341 1050 | Spline screw IS-M5x25 Fitment / change note → | 3 |
| 25 | 1128 084 1400 | Cover | 1 |
| 26 | 1128 405 1000 | Spark plug boot | 1 |
| 27 | 0000 998 0604 | Torsion spring | 1 |
| 28 | 0000 989 1004 | Grommet | 2 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 0000 405 0600 NLA | Ignition lead 1 m option | 1 |
| — | 0000 930 2251 | Ignition lead 10 m option | 1 |
| — | 0751 010 1110 | Lead 10 m / 33' option | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Historical fitment · 084
084: series 1124 replacement ignition assignment
1124 400 1308 and the listed flywheel pairings for series 1124; 200 mm ignition lead.
- Standard: 1124 400 1308 with flywheel 1124 400 1203.
- Heating: 1124 400 1308 with flywheel 1124 400 1207.
- Printed ignition-lead length: 200 mm (7 7/8 in). Preserve the printed metric and inch values; no rounding correction is inferred.
- TI01/1999 lists replacement combinations for the then-current machines, not every earlier configuration. Older machines are referred to Spare Parts for Previous Models in their own illustrated parts lists; no serial cutoff is supplied here.
- Use only the listed ignition-module/flywheel combinations. The source warns that incorrect combinations can cause excessive RPM or running in reverse; sharing a module number does not make all flywheels interchangeable.
- Universal replacement modules may differ from production modules in maker, shape and part number. The source describes installation/function compatibility within its assignments, not universal compatibility or a project hardware test.
- Some replacement modules require shortening the ignition lead and/or short-circuit wire and crimping a different short-circuit connector. The table gives ignition-lead lengths only; it supplies neither a short-circuit-wire length nor a connector part number. Do not infer that every row needs modification.
- Only the named models and printed series are covered. A shared IPL sheet does not extend this assignment to unnamed models or modern MS equivalents. This 1999 USA bulletin is historical guidance, not current availability.
Source: TI 1/1999, p. 1 · TI 1/1999, p. 2 — 1.1 general restrictions and 1.2.1 chainsaw assignments.
Part numbers (3)
- 1124 400 1308 — Replacement ignition moduleAssigned replacement · 084, series 1124, only with the listed flywheel branch
- 1124 400 1203 — Standard flywheelRequired pairing · 084, series 1124; standard only
- 1124 400 1207 — Heating flywheelRequired pairing · 084, series 1124; heating only
Service note · 084
084 EY-V ignition: replacement without electronic speed governor
Module 1124 400 1308 replaces governed CDIC 1124 400 1306 from X 31 237 198, with ignition-specific flywheel positioning.
X 31 237 198 — EY-V ignition introduced from this machine number on 084; earlier 084 retrofit remains conditional on ignition type and flywheel slot.
- New EY-V module 1124 400 1308 has NO electronic speed governor and replaces CDIC 1124 400 1306 WITH electronic speed governor. The TI permits the new module as a general replacement for all ignition versions ON MODEL 084, conditional on the correct flywheel slot. This does not authorize governor removal on unrelated models.
- The source describes defined cut-in rpm, retarded timing during starting and idle for smoother idling, a longer-burning spark and reliable combustion during starting. These are historical manufacturer claims, not new measurements. No numerical cut-in speed, timing angle or spark duration is supplied.
- The air gap MUST be maintained exactly: an excessive gap prevents proper ignition timing. No numerical air gap or tightening torque is supplied here, so none is invented. This is not a complete ignition-installation procedure.
- In figure 129TI001 the governed CDIC module is labeled P, the ungoverned version B, and arrows point to the corresponding flywheel slots. Use slot B for ignition WITHOUT speed cut-off and slot P for CDIC WITH electronic speed governor; geometry alone is not permission to choose either slot.
- Table remark 1 says the original CDIC module is no longer available from the factory; new EY-V MOQ H is 1. Both module rows include item 1 cable retainer, treated separately below. Later 084 G ignition sheet key 8 lists 1124 400 1308; this corroborates that number, not the fitment of neighboring 088/MS 880 ignition modules.
- Historical TI guidance for model 084 only; shared series 1124 does not extend these changes to 088, MS 880 or MS 881. No present-day supply guarantee, physical interchange test or model-identification serial range is implied. No hardware operation was performed.
Source: TI 18/1995, p. 1 · TI 18/1995, p. 2 — Section 1 introduction, feature list, figure 129TI001 and module rows.
Part numbers (2)
- 1124 400 1306 — Ignition module CDICoriginal governed module; historical factory supply ended · 084; EY-V ignition introduced from this machine number on 084; earlier 084 retrofit remains conditional on ignition type and flywheel slot.
- 1124 400 1308 — Ignition module EY-Vnew ungoverned module; MOQ 1; includes cable retainer · 084; EY-V ignition introduced from this machine number on 084; earlier 084 retrofit remains conditional on ignition type and flywheel slot.
Service note · 084
084 EY-V speed: 12,500 rpm only with bar and tensioned chain
Keep the former 12,250-rpm cut-off distinct from the new permissible maximum, not an assumed electronic limiter.
X 31 237 198 — EY-V ignition introduced from this machine number on 084; earlier 084 retrofit remains conditional on ignition type and flywheel slot.
- The page 2 note says introduction of EY-V changes the previous 12,250 rpm cut-off speed to a permissible maximum speed of 12,500 rpm. This specification refers to a saw WITH BAR AND PROPERLY TENSIONED CHAIN. It is not a bare-powerhead test target or an idle-speed specification.
- Page 1 explicitly says EY-V is WITHOUT an electronic speed governor. Therefore 12,500 rpm is retained as a PERMISSIBLE MAXIMUM, not a claimed electronic limiter or a guarantee against overspeed. The wording “changes the cut-off speed” does not erase this distinction.
- Flywheel slot B applies to ignition without speed cut-off; P applies to governed CDIC. The speed note does not supply carburetor settings, a live adjustment procedure, tachometer method or permission to run the saw. No numeric air-gap value is inferred from this speed limit.
- Historical TI guidance for model 084 only; shared series 1124 does not extend these changes to 088, MS 880 or MS 881. No present-day supply guarantee, physical interchange test or model-identification serial range is implied. No hardware operation was performed.
Source: TI 18/1995, p. 1 · TI 18/1995, p. 2 — Section 1 flywheel-slot rule and page 2 speed note.
No additional parts-table entry added.
Service note · 084
084 ignition hardware: included retainer and three screws/washers
Retainer changes from 1122 448 1200 to 1125 448 1201; unchanged fastener numbers increase from two to three.
X 31 237 198 — EY-V ignition introduced from this machine number on 084; earlier 084 retrofit remains conditional on ignition type and flywheel slot.
- Each ignition module includes item 1 cable retainer. Original retainer 1122 448 1200 becomes 1125 448 1201, MOQ H 1; remark 2 says the original retainer remains available for OLDER MACHINES. This is different from the old module’s ended factory supply.
- Spline screw IS-M5 x 25 remains 9022 341 1050 (table key 2); washer A 5.3 remains 9291 021 0120 (key 3). Remark 3 changes quantity of EACH from 2 to 3. Blank MOQ cells for these fasteners are not zero and the installation quantity is not an ordering minimum. All other parts remain as before; no torque is given.
- Later 084 G sheet lists washer at key 23 and screw at key 24, quantity 3 each, corroborating the changed installation quantities. It instead lists lead retainer 0000 448 1250 at key 11 and old 1122 448 1200 at key 12 (marked NLA), not TI-new 1125 448 1201. Preserve the later number/availability differences; no undocumented 1201-to-1250 supersession or retrospective rewrite of 1995 availability is inferred.
- Historical TI guidance for model 084 only; shared series 1124 does not extend these changes to 088, MS 880 or MS 881. No present-day supply guarantee, physical interchange test or model-identification serial range is implied. No hardware operation was performed.
Source: TI 18/1995, p. 2 — Complete ignition summary, inclusion item 1 and remarks 1–3.
Part numbers (4)
- 1122 448 1200 — Original cable retainerincluded item 1; retained for older machines in 1995 · 084; EY-V ignition introduced from this machine number on 084; earlier 084 retrofit remains conditional on ignition type and flywheel slot.
- 1125 448 1201 — New cable retainerincluded item 1; MOQ 1 · 084; EY-V ignition introduced from this machine number on 084; earlier 084 retrofit remains conditional on ignition type and flywheel slot.
- 9022 341 1050 — Spline screw IS-M5 x 25same number; quantity 2 to 3 · 084; EY-V ignition introduced from this machine number on 084; earlier 084 retrofit remains conditional on ignition type and flywheel slot.
- 9291 021 0120 — Washer A 5.3same number; quantity 2 to 3 · 084; EY-V ignition introduced from this machine number on 084; earlier 084 retrofit remains conditional on ignition type and flywheel slot.
Wrong number or missing part for the 084? Report a correction →