← 034 · 036 · MS 340/360

Stihl 1125 · Section K · 10 of 17 · 36 parts

Air filter

Fits 036.

Parts diagrams →

Historical fitment & changes (14) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
110101111121314151617181922021222325262728293303132456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (36)

PosPart numberDescriptionQty
1 1125 141 2200 Manifold 1
2 1119 141 1800 Sleeve 1
3 9771 021 2580 Hose clip Ø 34x7 1
4 not sold separately Hose 3.1x6.7x102 mm not available as a separate item 1
5 1119 121 8600 Washer 1
6 1125 120 0613 Carburetor C3A-S31E 1
6 1125 120 0614 Carburetor CA-S65 1
7 1125 120 0609 Carburetor C3A-S27D 1
8 1125 120 0615 Carburetor C3A-S39B 1
9 1125 120 0612 Carburetor C3-S52 1
10 1125 123 7506 Grommet Fitment / change note → 1
11 1125 123 7501 Grommet Fitment / change note → 1
12 9210 260 0700 Hexagon nut M5 2
13 1125 120 1602 Air filter Fitment / change note → 1
14 1125 121 9100 Bushing Fitment / change note → 1
15 1125 120 1607 Air filter Fitment / change note → 1
16 1125 122 4900 Filter insert Fitment / change note → 1
17 1125 141 8300 Slotted nut Fitment / change note → 2
18 1125 120 1605 Air filter Fitment / change note → 1
19 1125 120 1600 Air filter Fitment / change note → 1
20 1125 120 1617 Air filter, fleece Fitment / change note → 1
21 1125 120 1622 Air filter, fleece Fitment / change note → 1
22 1125 120 1615 Air filter, fleece Fitment / change note → 1
23 1125 120 1620 Air filter, fleece Fitment / change note → 1
25 1117 182 4500 Torsion spring 1
26 9371 470 2640 Cylindrical pin 5x24 1
27 1125 182 1502 Throttle rod 1
28 1125 185 2002 Choke rod Fitment / change note → 1
29 1125 442 1601 Contact spring 1
30 1125 442 1600 Contact spring Fitment / change note → 1
31 1125 182 0901 Switch shaft Fitment / change note → 1
32 1117 182 0805 Lockout lever 1
Not numbered on the diagram — assemblies, kits and options
— 0000 930 2804 Hose 3.1x6.7 mm x 1 m not illustratedoption 1
— 1125 120 1612 Air filter 1
— 1125 120 1610 Air filter 1
— 1125 120 1626 Air filter, fleece 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · 036

036 compensator retrofit: complete assembly and lower tank vent required

Retrofit threshold X 32 185 626 is not factory introduction X 32 622 640.

  • 036 retrofit restriction: ONLY from X 32 185 626, with the LOWER tank vent providing clearance, and ONLY AS A COMPLETE ASSEMBLY of air filter, metering end cover with compensator connector and carburetor box cover. Factory introduction X 32 622 640 is a DIFFERENT threshold. TI28/1995 reverses its tank-vent and cap-retainer serials between prose and summary; TI30 agrees with its vent prose but is not an explicit correction. Preserve that conflict; verify the actual housing/vent configuration, not serial alone.
  • New filter has a much larger area, felt fabric, inner-half opening for the compensator connector and retaining lugs for the carburetor box cover. Sleeve 1125 121 9100 connects the clean-air side to the connector on the modified metering end cover, exposing the OUTSIDE of the metering diaphragm to clean-air pressure.
  • The TI describes this compensator as preventing mixture enrichment as the filter gets dirty, so the high-speed screw need not be readjusted merely for increasing filter contamination. This is a historical functional claim, not a guarantee for damaged filters or a deletion of maintenance. No numeric filtration efficiency, service interval or carburetor setting is supplied.
  • Page 6 explicitly separates ORIGINAL upper diagram from NEW lower diagram. Their item numbers resolve against page 7, not later IPL positions. The complete-system restriction is not permission to mix individual new and old filter/cover components.
  • Historical TI guidance for the named models and stated versions only. Shared series and later IPL sheets do not extend applicability to other variants or successors. Supply statements are historical, not present stock guarantees or verified physical interchange. No hardware operation was performed.

Source: TI 30/1995, p. 1 · TI 30/1995, p. 4 · TI 30/1995, p. 5 · TI 30/1995, p. 6 · TI 30/1995, p. 7 — Section 1.2 features, 1.2.2 restrictions and assembly figures.

Part numbers (3)
  • 1125 121 9100 — Compensator sleeveclean-air connection · 036; Section 1.2 features, 1.2.2 restrictions and assembly figures
  • 1125 121 0804 — Metering end cover with connectorcomplete-system component · 036; Section 1.2 features, 1.2.2 restrictions and assembly figures
  • 1125 140 1903 — Carburetor box covercomplete-system component · 036; Section 1.2 features, 1.2.2 restrictions and assembly figures

Service note · 036

036 air-filter halves: original, felt and companion parts

Preserve the paired halves, sleeve, filter insert and slotted nut.

  • 036 retrofit restriction: ONLY from X 32 185 626, with the LOWER tank vent providing clearance, and ONLY AS A COMPLETE ASSEMBLY of air filter, metering end cover with compensator connector and carburetor box cover. Factory introduction X 32 622 640 is a DIFFERENT threshold. TI28/1995 reverses its tank-vent and cap-retainer serials between prose and summary; TI30 agrees with its vent prose but is not an explicit correction. Preserve that conflict; verify the actual housing/vent configuration, not serial alone.
  • Page 7 item 1 plain half 1125 120 1600 becomes 1125 120 1602, INCLUDING sleeve item 3 (1125 121 9100). Item 2 plain half 1125 120 1605 becomes 1125 120 1607, INCLUDING filter insert item 4 (1125 122 4900).
  • Separate material rows: original FLOCKED item 1 half 1125 120 1615 gives way to new FELT half 1125 120 1617, including sleeve; original FLOCKED item 2 half 1125 120 1620 gives way to FELT half 1125 120 1622, including filter insert. Do not merge the plain and material-specific alternatives or interpret the dashes as ordering numbers.
  • Slotted nut 1113 141 8305 becomes 1125 141 8300; original nut supplied only while stocks last. Original filter versions remain available as spares for older machines. Factory introduction X 32 622 640. Later sheet K calls the material fleece; this does not erase the TI flocked-versus-felt distinction.
  • Historical TI guidance for the named models and stated versions only. Shared series and later IPL sheets do not extend applicability to other variants or successors. Supply statements are historical, not present stock guarantees or verified physical interchange. No hardware operation was performed.

Source: TI 30/1995, p. 4 · TI 30/1995, p. 5 · TI 30/1995, p. 6 · TI 30/1995, p. 7 — Section 1.2.3 filter rows 1–5 and remarks.

Part numbers (12)
  • 1125 120 1600 — Original plain half, item 1old spare · 036; Section 1.2.3 filter rows 1–5 and remarks
  • 1125 120 1602 — New plain half, item 1includes sleeve · 036; Section 1.2.3 filter rows 1–5 and remarks
  • 1125 120 1605 — Original plain half, item 2old spare · 036; Section 1.2.3 filter rows 1–5 and remarks
  • 1125 120 1607 — New plain half, item 2includes filter insert · 036; Section 1.2.3 filter rows 1–5 and remarks
  • 1125 120 1615 — Original flocked half, item 1old spare · 036; Section 1.2.3 filter rows 1–5 and remarks
  • 1125 120 1617 — New felt half, item 1includes sleeve · 036; Section 1.2.3 filter rows 1–5 and remarks
  • 1125 120 1620 — Original flocked half, item 2old spare · 036; Section 1.2.3 filter rows 1–5 and remarks
  • 1125 120 1622 — New felt half, item 2includes filter insert · 036; Section 1.2.3 filter rows 1–5 and remarks
  • 1125 121 9100 — Sleevenew item 3 · 036; Section 1.2.3 filter rows 1–5 and remarks
  • 1125 122 4900 — Filter insertnew item 4 · 036; Section 1.2.3 filter rows 1–5 and remarks
  • 1113 141 8305 — Original slotted nutstocks only · 036; Section 1.2.3 filter rows 1–5 and remarks
  • 1125 141 8300 — New slotted nutreplacement · 036; Section 1.2.3 filter rows 1–5 and remarks

Service note · 034 / 036

034 / 036 replacement carburetor: original end cover supplied

Carburetor 0651 includes cover 0803 for non-compensator 036 and 034 use.

  • New replacement carburetor 1125 120 0651 replaces 1125 120 0606. New assembly rows include metering end cover 1125 121 0804 (replacing 1125 121 0803) and collar screw 1120 122 6601 (replacing 4132 122 6600). The original carburetor is NO LONGER factory available; original cover and collar screw remain spares for older machines.
  • ORIGINAL END COVER 1125 121 0803 is ALSO included in new carburetor supply FOR 036 WITHOUT COMPENSATOR AND FOR 034. This supply provision is not authorization to retrofit the full 036 compensator system to 034. Factory introduction X 32 622 640 in this 036 bulletin must not become a 034 cutoff.
  • Later 036 K lists 0613/0614/0609/0615/0612 and 034 L lists other carburetor numbers, not TI 0651. Later 036 L retains both end covers and both screw versions, but its carburetor model labels are not proof of the TI 0651 manufacturer/model. No universal carburetor supersession chain or adjustment setting inferred.
  • Historical TI guidance for the named models and stated versions only. Shared series and later IPL sheets do not extend applicability to other variants or successors. Supply statements are historical, not present stock guarantees or verified physical interchange. No hardware operation was performed.

Source: TI 30/1995, p. 5 · TI 30/1995, p. 6 · TI 30/1995, p. 7 — Sections 1.2.1 and 1.2.3 carburetor rows 6–8 and remarks.

Part numbers (6)
  • 1125 120 0606 — Original carburetorno longer factory available · 036 summary version change; not an additional 034 fitment claim
  • 1125 120 0651 — Replacement carburetorincludes original cover for stated non-compensator use · 034 / 036; Sections 1.2.1 and 1.2.3 carburetor rows 6–8 and remarks
  • 1125 121 0803 — Original end coverincluded for non-compensator use · 034 / 036; Sections 1.2.1 and 1.2.3 carburetor rows 6–8 and remarks
  • 1125 121 0804 — New compensator end covernew assembly component · 036 summary version change; not an additional 034 fitment claim
  • 4132 122 6600 — Original collar screwretained spare · 036 summary version change; not an additional 034 fitment claim
  • 1120 122 6601 — New collar screwnew assembly component · 036 summary version change; not an additional 034 fitment claim

Service note · 036

036 compensator carburetor screws: LOCTITE 221 exclusion zone

Keep adhesive off the first two to three thread turns.

  • On repair of a carburetor WITH COMPENSATOR COVER, clean HIGH- AND LOW-SPEED adjusting screws thoroughly before installation and recoat with fresh LOCTITE 221. The source says these screws are sealed with this product.
  • DO NOT APPLY LOCTITE TO THE FIRST TWO TO THREE TURNS OF THE THREAD. Under NO CIRCUMSTANCES may adhesive get into the carburetor. This does not prescribe a substitute adhesive or application to every carburetor screw.
  • No screw ordering number, application amount, cure time, torque or mixture setting is printed. Do not derive these from later catalog screws or transfer the instruction to non-compensator variants.
  • Historical TI guidance for the named models and stated versions only. Shared series and later IPL sheets do not extend applicability to other variants or successors. Supply statements are historical, not present stock guarantees or verified physical interchange. No hardware operation was performed.

Source: TI 30/1995, p. 5 — Section 1.2.2 adjusting-screw service warning.

No additional parts-table entry added.

Service note · 036

036 carburetor box cover: seasonal shutter and changed components

Summer seals the molded screen; winter moves the cover into the lower slot.

  • 036 retrofit restriction: ONLY from X 32 185 626, with the LOWER tank vent providing clearance, and ONLY AS A COMPLETE ASSEMBLY of air filter, metering end cover with compensator connector and carburetor box cover. Factory introduction X 32 622 640 is a DIFFERENT threshold. TI28/1995 reverses its tank-vent and cap-retainer serials between prose and summary; TI30 agrees with its vent prose but is not an explicit correction. Preserve that conflict; verify the actual housing/vent configuration, not serial alone.
  • Combustion air intake moves from the TOP gap to the BOTTOM between carburetor box cover and tank housing. A twist-lock lever (1) turns 90 degrees to secure the cover to the filter. Original wire-mesh prefilter is replaced by an integrally molded plastic screen.
  • SUMMER: cover (2), ordering number 1121 141 2900 in the summary, seals the screen. WINTER: remove this cover and fit it in the SLOT AT THE BOTTOM of the carburetor box cover (figure arrow), allowing warm cylinder air to mix with cold air. No temperature threshold or all-winter operating permission is supplied.
  • Carburetor box cover 1125 140 1902 becomes 1125 140 1903, including items 10–15 as applicable to each version. Original prefilter 1125 120 1500, helical spring 0000 997 1335, detent 1125 141 2101 and B3.9 x16 self-tapping screw 9099 021 2790 have DASHES in the new column; they are not components to transfer into the new cover. Twist lock 1121 141 2300 becomes 1130 141 2300; new cover 1121 141 2900 is added.
  • Original cover and marked original components remain spares for older machines; all other parts as before. Factory introduction X 32 622 640. Later sheet P also lists cover 1904/prefilter 1501 and screw 9074 478 3025, differing from the TI original 1902/1500/9099 021 2790; no supersession inferred.
  • Historical TI guidance for the named models and stated versions only. Shared series and later IPL sheets do not extend applicability to other variants or successors. Supply statements are historical, not present stock guarantees or verified physical interchange. No hardware operation was performed.

Source: TI 30/1995, p. 5 · TI 30/1995, p. 6 · TI 30/1995, p. 7 — Section 1.2 cover operation and summary rows 9–15.

Part numbers (9)
  • 1125 140 1902 — Original carburetor box coverold spare · 036; Section 1.2 cover operation and summary rows 9–15
  • 1125 140 1903 — New carburetor box covermodified air system · 036; Section 1.2 cover operation and summary rows 9–15
  • 1125 120 1500 — Original wire-mesh prefilterdeleted from new configuration; old spare · 036; Section 1.2 cover operation and summary rows 9–15
  • 1121 141 2300 — Original twist lockold spare · 036; Section 1.2 cover operation and summary rows 9–15
  • 1130 141 2300 — New twist lock90-degree lever · 036; Section 1.2 cover operation and summary rows 9–15
  • 0000 997 1335 — Original helical springold configuration only · 036; Section 1.2 cover operation and summary rows 9–15
  • 1125 141 2101 — Original detentold configuration only · 036; Section 1.2 cover operation and summary rows 9–15
  • 9099 021 2790 — Original B3.9x16 screwold configuration only · 036; Section 1.2 cover operation and summary rows 9–15
  • 1121 141 2900 — Seasonal coversummer screen seal; winter lower slot · 036; Section 1.2 cover operation and summary rows 9–15

Service note · 024 / 036

036 switch shaft: shorter tang; original remains usable on 024

0900 becomes 0901 with the short-circuit-wire tang shortened by 2 mm.

  • In connection with the modified 036 air filter, switch shaft 1125 182 0900 is replaced by 1125 182 0901. The tang for the SHORT CIRCUIT WIRE is shortened by 2 mm (0.08 inch). This is a part revision, not an instruction to cut an old shaft.
  • Original 1125 182 0900 CAN STILL BE USED FOR MODEL 024. The 024 exception concerns the original shaft only; it does not extend the new 036 air-filter system or its serial thresholds to 024. Later 036 K key31 lists 0901 and 024 J retains 0900.
  • No separate shaft introduction serial or field-modification dimensions are supplied. Earlier TI28 housing-shaft statements remain separate; this TI establishes this specific 0900-to 0901 change without resolving the older tank-vent serial conflict.
  • Historical TI guidance for the named models and stated versions only. Shared series and later IPL sheets do not extend applicability to other variants or successors. Supply statements are historical, not present stock guarantees or verified physical interchange. No hardware operation was performed.

Source: TI 30/1995, p. 5 — Section 1.2.2 switch shaft paragraph.

Part numbers (2)
  • 1125 182 0900 — Original switch shaft036 original; continued 024 use · 024 / 036; Section 1.2.2 switch shaft paragraph
  • 1125 182 0901 — Shorter-tang switch shaft036 modified-air-filter version · 036 with modified air filter; not a new 024 fitment claim

Service note · 036

036 new-filter kits: preheating and ElastoStart contents

New kits retain their separate cover and paired-filter-half inclusions.

  • 036 retrofit restriction: ONLY from X 32 185 626, with the LOWER tank vent providing clearance, and ONLY AS A COMPLETE ASSEMBLY of air filter, metering end cover with compensator connector and carburetor box cover. Factory introduction X 32 622 640 is a DIFFERENT threshold. TI28/1995 reverses its tank-vent and cap-retainer serials between prose and summary; TI30 agrees with its vent prose but is not an explicit correction. Preserve that conflict; verify the actual housing/vent configuration, not serial alone.
  • For 036 WITH THE NEW AIR FILTER SYSTEM, intake air preheating kit 1125 007 1035 becomes 1125 007 1037. Included carburetor box cover 1125 140 1906 becomes 1125 140 1907. All other kit parts as before; this is not a complete newly enumerated kit roster.
  • Repair kit (ElastoStart) 1125 900 5002 becomes 1125 900 5004, INCLUDING FILTER ITEMS 1 AND 2. The TI does not select a single material-specific pair from the multiple item1/item2 rows or print a complete starter-component inventory; do not invent that specificity.
  • Original kits and original preheating cover remain available for older machines. Factory introduction X 32 622 640. Later sheet P lists 1037 and 1907; the note does not silently substitute later kit 1042 or assume kits universally interchangeable.
  • Historical TI guidance for the named models and stated versions only. Shared series and later IPL sheets do not extend applicability to other variants or successors. Supply statements are historical, not present stock guarantees or verified physical interchange. No hardware operation was performed.

Source: TI 30/1995, p. 5 · TI 30/1995, p. 7 — Sections 1.2.2 and 1.2.3 special accessories.

Part numbers (6)
  • 1125 007 1035 — Original preheating kitolder-machine spare · 036; Sections 1.2.2 and 1.2.3 special accessories
  • 1125 007 1037 — New preheating kitnew filter system · 036; Sections 1.2.2 and 1.2.3 special accessories
  • 1125 140 1906 — Original preheating coverincluded in old kit · 036; Sections 1.2.2 and 1.2.3 special accessories
  • 1125 140 1907 — New preheating coverincluded in new kit · 036; Sections 1.2.2 and 1.2.3 special accessories
  • 1125 900 5002 — Original ElastoStart repair kitolder-machine spare · 036; Sections 1.2.2 and 1.2.3 special accessories
  • 1125 900 5004 — New ElastoStart repair kitincludes filter items 1 and 2 · 036; Sections 1.2.2 and 1.2.3 special accessories

Service note · 036

036 tank housing: longer collar screw for modified air filter

0803 becomes 0813 with screw 4116 122 6600 from X 32 622 640.

  • Tank housing 1125 350 0803 is replaced by 1125 350 0813, INCLUDING longer collar screw 4116 122 6600 in place of 1125 122 6600. This change is connected to the modified air filter in section1.2. Introduction FROM X 32 622 640.
  • Original housing supplied only while factory stocks last; original collar screw REMAINS A SPARE FOR OLDER MACHINES. Longer is qualitative here: no length, mounting torque or independent permission to put the longer screw in any old housing is printed.
  • This housing revision is separate from TI28 same-number 0803 vent revision and TI30 retrofit eligibility X 32 185 626. Later 036 H lists housing 1125 350 0818 and both collar screws; that does not establish an 0813-to 0818 supersession.
  • Historical TI guidance for the named models and stated versions only. Shared series and later IPL sheets do not extend applicability to other variants or successors. Supply statements are historical, not present stock guarantees or verified physical interchange. No hardware operation was performed.

Source: TI 30/1995, p. 8 — Section 2 complete housing summary and supply remarks.

Part numbers (4)
  • 1125 350 0803 — Original tank housingstocks-only original · 036; Section 2 complete housing summary and supply remarks
  • 1125 350 0813 — New tank housingincludes longer collar screw · 036; Section 2 complete housing summary and supply remarks
  • 1125 122 6600 — Original collar screwolder-machine spare · 036; Section 2 complete housing summary and supply remarks
  • 4116 122 6600 — Longer collar screwincluded in new housing · 036; Section 2 complete housing summary and supply remarks

Historical fitment · 034 / 036

034/036: universal replacement contact spring

New connector tag accepts the thermostat flag; broader spare scope than the new 036 option.

  • Contact spring 1121 442 1600 is replaced by 1125 442 1600 to coincide with the new carburetor heating system. Thermostatic-switch flag connector fits the tag indicated by the arrow in drawing 133TI013.
  • Parts availability explicitly calls 1125 442 1600 a UNIVERSAL replacement for ALL versions of 034 and 036. This broader spring statement does not make the new VH carburetor option universal or establish a complete retrofit.
  • Current 034 air-filter/control sheet shows 1125 442 1601; current 036 sheet has both1600 and1601. Retain the TI 1600 replacement claim and later IPL difference without inventing a 1600→1601 supersession or variant equivalence. No serial cutoff supplied.
  • Historical TI 21/1996 evidence only; no present stock status, calendar introduction date or universal retrofit inferred. No hardware operation was performed.

Source: TI 21/1996, p. 1 · TI 21/1996, p. 2 — universal replacement contact spring.

Part numbers (2)
  • 1121 442 1600 — Contact springOriginal · All versions of 034/036 per TI; assembly links are exact base-model sheets
  • 1125 442 1600 — Contact spring with connector tagUniversal historical replacement · All versions of 034/036 per TI; assembly links are exact base-model sheets

Service note · 036

036: carburetor-box wiring and TOP 1125 plate

Three wires through the grommet; cold-start lever position and unpinched wiring during assembly.

  • Position harness grommet correctly in tank housing; ALL THREE wires pass through it. Drawing 138TI016: blue heating-element wire(1) terminal pin goes into connector sleeve; tube(2) completely covers joint. Short-circuit wire sleeve(3) goes into switch-shaft seat. Yellow-green ground-wire sleeve(4) goes into CONTACT-SPRING LOOP, not its thermostat tag.
  • First push carburetor only until flush with collar screws, without pinching wires. Push Master Control lever all the way down to COLD START. Fit thermostat flag connector(1) to contact-spring TAG; slip heating element(2) over collar screws onto carburetor; fit plate(3) with TOP 1125 oriented as drawing 138TI014 shows.
  • Carefully advance carburetor over collar screws to the manifold-flange stop, check wire positions against138TI015 and tighten M5 hexagon nuts. TI supplies NO torque; no value imported from a different model. The installation sequence is source guidance, not evidence of a performed repair or complete conversion authorization.
  • Extracted body misreads diagram identifier as4138TI016 and interleaves labels; original scan confirms138TI016 and the distinct loop/tag connections. Canonical OCR remains unchanged.
  • Historical TI 21/1996 evidence only; no present stock status, calendar introduction date or universal retrofit inferred. No hardware operation was performed.

Source: TI 21/1996, p. 1 · TI 21/1996, p. 2 · TI 21/1996, p. 3 · TI 21/1996, p. 4 — carburetor-box wiring and TOP 1125 plate.

Part numbers (5)
  • 1125 440 3000 — Wiring harnessThree wires through grommet · 036 carburetor-heating installation
  • 1125 123 7500 — GrommetPosition in tank housing · 036 carburetor-heating installation
  • 1125 442 1600 — Contact springGround loop and thermostat tag are distinct · 036 carburetor-heating installation
  • 1128 434 5101 — Heating elementFits before plate · 036 carburetor-heating installation
  • 1125 121 9900 — Heating plateTOP 1125 orientation · 036 carburetor-heating installation

Service note · 034 / 036

034 / 036: fleece filter under unchanged numbers

Fleece replaces flocked wire cloth; old stock, cleaning direction and replacement limits remain distinct.

  • TI38/1996 replaces flocked wire cloth with fleece under UNCHANGED replacement-part numbers. Introduction is IN PROGRESS, without a serial cutoff. Remark 1 says the unmodified version is supplied until existing stocks are exhausted. A number alone therefore does not identify the material of an old-stock filter; this is a historical supply statement, not a current stock guarantee.
  • Both 034/036 rows, 1125 120 1615 and 1125 120 1620, carry remarks 1 and 3; remark 3 says SEE TI30.95. TI38 does not declare these two numbers interchangeable or a single assembly ordering number.
  • TI30/1995 page 7 identifies 1615 and 1620 as the ORIGINAL flocked halves, with new felt halves 1617 and 1622 in the different 036 compensator system. TI38 changes material under the older numbers; it does not collapse the two system generations.
  • TI30/1995 page 5 restricts the new filter, compensator metering end cover and carburetor box cover to a COMPLETE ASSEMBLY on 036 from X 32 185 626, requiring lower tank-vent clearance. Production introduction X 32 622 640 is separate, and neither is a TI38 fleece cutoff. This does not authorize the full conversion on 034. The earlier TI28 tank-vent/cap-retainer serial conflict remains unresolved; verify actual configuration rather than serial alone.
  • Later 034 sheet M cites TI08/2000 and TI31/2001 and retains these filter numbers; this is an exact-model navigation binding, not proof that its whole assembly existed in 1996. Original IPL contents and later restrictions remain unchanged.
  • The source calls fleece especially suitable for dry and dusty conditions. Its rougher surface may look heavily contaminated when only lightly loaded; appearance alone does not establish loading. Clean DAILY OR when there is a noticeable loss of power during cutting. The observation about appearance does not cancel that interval.
  • If possible, carefully blow out at LOW PRESSURE from the CLEAN AIR SIDE. For stubborn dirt or caked fleece, wash in a clean, NON-FLAMMABLE solution, for example warm soapy water. DO NOT CLEAN WITH A BRUSH: it forces dirt into the fleece. No pressure value, drying time or alternate solvent is specified.
  • The source attributes improved filtering efficiency to the material structure, not a measured result here. Some trapped particles cannot be cleaned out; replace the filter when cleaning intervals become too short for practical use, or when noticeable cutting-power loss persists after thorough cleaning.
  • Historical guidance for these named models and filter configurations only; no successor-model fitment, universal interchange or material identity inferred from a shared part number. No hardware operation was performed.

Source: TI 38/1996, p. 1 · TI 38/1996, p. 2 — Complete filter-material and servicing guidance; exact model summary rows and remarks.

Referenced bulletin evidence: TI 30/1995, p. 5 · TI 30/1995, p. 7 — Previously reviewed 036 complete-system restriction and original-versus-new filter-half rows.

Part numbers (2)
  • 1125 120 1615 — Air filter, first printed rowunchanged older-system material-revision number · 034 / 036; TI38/1996 row and configuration conditions
  • 1125 120 1620 — Air filter, second printed rowunchanged older-system material-revision number · 034 / 036; TI38/1996 row and configuration conditions

Historical fitment · 036

036 EPA carburetor: screwdriver-guide grommet change

New grommet accompanies the new carburetor; old grommet remains a spare.

  • Grommet 1125 123 7501 guides the carburetor screwdriver and replaces 1125 123 7506 together with introduction of the new carburetor in section 1. Original version remains available as a spare (remark 1). No independent universal retrofit or serial cutoff is stated.
  • Historical TI43/1997 guidance for the named 036 configuration only, not 034, MS 360 or every 036 variant. Supply remarks describe 1997, not current stock or verified physical interchange. No hardware operation was performed.

Source: TI 43/1997, p. 4 · TI 43/1997, p. 6 — Section2; summary item9 and remark1.

Part numbers (2)
  • 1125 123 7506 — Original grommetRetained spare · 036; Section2; summary item9 and remark1
  • 1125 123 7501 — New screwdriver-guide grommetIntroduced with EPA carburetor · 036; Section2; summary item9 and remark1

Conditional replacement · 036

036: revised choke lever and throttle rod fit older machines

Backward compatibility is explicit for these two linkage parts, not the EPA carburetor or muffler.

  • Choke lever 1125 185 2001 changes to 1125 185 2002, and throttle rod 1125 182 1500 to 1125 182 1501 in connection with the new carburetor. Both NEW linkage versions can also be used for OLDER machines (remark 4). Original versions are supplied from factory only while existing stocks last (remark 3). Do not transfer this backward-compatibility statement to the EPA-only complete carburetor or muffler.
  • Historical TI43/1997 guidance for the named 036 configuration only, not 034, MS 360 or every 036 variant. Supply remarks describe 1997, not current stock or verified physical interchange. No hardware operation was performed.

Source: TI 43/1997, p. 4 · TI 43/1997, p. 6 — Section3; summary items10/11 and remarks3/4.

Part numbers (4)
  • 1125 185 2001 — Original choke leverFactory supply only while stocks last · 036; Section3; summary items10/11 and remarks3/4
  • 1125 185 2002 — New choke leverAlso suitable for older036 · 036; Section3; summary items10/11 and remarks3/4
  • 1125 182 1500 — Original throttle rodFactory supply only while stocks last · 036; Section3; summary items10/11 and remarks3/4
  • 1125 182 1501 — New throttle rodAlso suitable for older036 · 036; Section3; summary items10/11 and remarks3/4

Conditional replacement · 034 / 036

034 / 036: revised choke lever and throttle rod

Territory-related control changes are in progress; new parts may also be used on older machines.

in progress — Section 2 controls only; territories unspecified, no serial cutoff; new versions permitted on older machines.

  • Choke lever 1125 185 2001 is deleted and replaced by 1125 185 2002 IN CONNECTION WITH MODIFICATIONS ON VERSIONS FOR CERTAIN SALES TERRITORIES. Territories are not named; this is not a global market identifier. Throttle rod 1125 182 1500 is replaced by 1125 182 1501.
  • Both new versions CAN ALSO BE USED IN OLDER MACHINES. Introduction is IN PROGRESS, with NO SERIAL CUTOFF in section 2; do not transfer the tank-only X 39 108 850 cutoff. The two-row summary marks BOTH original versions NO LONGER AVAILABLE FROM FACTORY. No mandatory paired-kit installation, geometry, adjustment dimension or reciprocal old-part fit is stated.
  • Exact 034 air-filter/throttle-control and 036 air-filter IPLs list new choke part 1125 185 2002 (called choke rod there), but list later throttle rod 1125 182 1502, NOT TI 11’s 1125 182 1501. The terminology and suffix difference are retained, not silently corrected or inferred as a further supersession. No extension to later MS 360 or QS control configurations from shared numbers.
  • Historical TI 11/1998, models 034/036, series 1125; QS is included only where the tank section expressly names it. Shared parts do not extend these changes to MS 360 or other models. Factory supply statements are historical, not current availability. Source-stated replacement permission is not physical-fit verification. No hardware operation was performed.

Source: TI 11/1998, p. 3 — Section 2 complete prose, both summary rows, in-progress introduction and availability remark.

Part numbers (4)
  • 1125 185 2001 — Original choke leverDeleted; no longer available from factory · 034/036; exact variants and conditions in this note
  • 1125 185 2002 — New choke leverAlso usable on older machines · 034/036; exact variants and conditions in this note
  • 1125 182 1500 — Original throttle rodNo longer available from factory · 034/036; exact variants and conditions in this note
  • 1125 182 1501 — New throttle rodAlso usable on older machines; distinct from later IPL1502 · 034/036; exact variants and conditions in this note

Wrong number or missing part for the 036? Report a correction →