← 029/039 · MS 290/310/390

Stihl 1127 · Section A · 1 of 12 · 20 parts

Cylinder 029

Fits 029.

Parts diagrams →

Historical fitment & changes (2) — includes parts and conditions not shown on this drawing.

This drawing carries 2 bore sizes — Ø 45 mm = 54.0 cc (029), Ø 46 mm = 56.5 cc (029, MS 290 Farm Boss). Not interchangeable — measure your cylinder before ordering.

Position —

Go to table row → Where else is this used →
1101111121213141516171823455677889
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (20)

PosPart numberDescriptionQty
1 1127 020 1210 Cylinder with piston Ø 46 mm Fitment / change note → — 029, MS 290 Farm Boss 1
2 1127 030 2003 Piston Ø 46 mm Fitment / change note → — 029, MS 290 Farm Boss 1
3 1127 030 2000 Piston Ø 45 mm Fitment / change note → — 029 1
4 1110 034 1500 Piston pin 10x6x32 1
5 9463 650 1000 Snap ring 10 2
6 0000 988 5211 Connector 1
7 1118 034 3001 Piston ring Ø 46x1.5 mm Fitment / change note → — 029, MS 290 Farm Boss 2
8 1113 034 3006 Piston ring Ø 45x1.5 mm Fitment / change note → — 029 2
9 9512 003 2340 Needle cage 10x14x13 1
10 1127 030 0402 NLA Crankshaft 1
10 1127 030 0411 Crankshaft 1
11 9503 003 0440 Grooved ball bearing 6203 2
12 9639 010 1743 Oil seal 17x30x4.4 2
12 9639 003 1743 Oil seal 17x30x4.4 2
13 1127 021 2500 Engine pan 1
14 9075 478 4735 Pan head self-tapping screw IS-D6x52 4
15 0783 830 2000 Tube of sealant Dirko HT red 1
16 1127 084 0900 Shroud 1
17 1127 084 4100 Shutter 1
18 9075 478 3015 Pan head self-tapping screw IS-D4x15 2

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Conditional replacement · 029

029 SUPER: larger bore, matched piston and retained older spares

The 46 mm, 56.5 cm³ engine replaces the 45 mm version; stroke is unchanged.

  • Historical TI46/1997 guidance for the named 029/039 configurations only, not MS successors or every shared-sheet variant. No hardware operation was performed.
  • The new sales designation is 029 SUPER. Bore increases by 1 mm (0.04 in), displacement by approximately 2.5 cm³ (0.15 cu.in). New displacement 56.5 cm³ (3.45 cu.in), bore 46 mm (1.81 in), power 2.8 kW (3.8 bhp); piston stroke is unchanged, with no stroke value supplied here.
  • Cylinder-with-piston assembly 1127 020 1200 becomes 1127 020 1210. The table says including items 2–5: these are old/new diameter alternatives, not permission to mix 45 mm and 46 mm pistons/rings.
  • 45 mm piston 1127 030 2000 and ring 1113 034 3006 remain available as spares for older machines. New 46 mm piston is 1127 030 2003 with ring 1118 034 3001. Each piston includes its corresponding ring; no mixed-diameter compatibility is claimed.
  • Nameplate 1127 967 1505 becomes 1127 967 1507; the older nameplate remains a spare for older machines. All other parts as before. Original cylinder assembly supplied only while factory stocks last. Introduction in progress; no numeric serial cutoff or current availability claimed.

Source: TI 46/1997, p. 1 · TI 46/1997, p. 2 — Section 1 specification and summary rows 1–6.

Part numbers (8)
  • 1127 020 1200 — Original cylinder with pistonHistorical version · 029; match stated engine diameter
  • 1127 020 1210 — New 46 mm cylinder with pistonHistorical version · 029; match stated engine diameter
  • 1127 030 2000 — 45 mm pistonHistorical version · 029; match stated engine diameter
  • 1127 030 2003 — 46 mm pistonHistorical version · 029; match stated engine diameter
  • 1113 034 3006 — 45 mm piston ringHistorical version · 029; match stated engine diameter
  • 1118 034 3001 — 46 mm piston ringHistorical version · 029; match stated engine diameter
  • 1127 967 1505 — Original 029 nameplateHistorical version · 029; match stated engine diameter
  • 1127 967 1507 — New nameplateHistorical version · 029; match stated engine diameter

Service note · 029 / 039

029 / 039: black ring compressor covers three piston sizes

1127 893 2601 covers 029 pistons of 45/46 mm and the 039 piston of 49 mm.

  • Historical TI46/1997 guidance for the named 029/039 configurations only, not MS successors or every shared-sheet variant. No hardware operation was performed.
  • Ring compressor 1127 893 2600 had to be modified for the larger 029 piston. New 1127 893 2601 is BLACK plastic rather than WHITE and is suitable for all stated 029 pistons (45 mm,46 mm) and 039 pistons (49 mm). The old tool is not thereby approved for the larger piston.
  • Original tool supplied from factory only while stocks last; introduction in progress. Tool compatibility is not cylinder or piston interchange.

Source: TI 46/1997, p. 1 · TI 46/1997, p. 2 — Section 1 service note and summary row 7.

Part numbers (2)
  • 1127 893 2600 — Original white ring compressorSpecial tool · Only stated 029/039 diameters
  • 1127 893 2601 — New black ring compressorSpecial tool · Only stated 029/039 diameters

Wrong number or missing part for the 029? Report a correction →