Stihl 1127 · Section K · 10 of 12 · 39 parts
Carburetor HD-18C, HD-21C (only USA)
Fits 029, 039.
Historical fitment & changes (4) — includes parts and conditions not shown on this drawing.
Parts (39)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4116 121 5100 | Inlet needle | 1 |
| 2 | 4116 121 5000 | Inlet control lever | 1 |
| 3 | 4116 122 3002 | Spring | 1 |
| 4 | 1113 121 9200 | Spindle | 1 |
| 5 | 1114 122 7400 | Round head screw | 1 |
| 6 | 1128 121 5403 | Valve jet Fitment / change note → | 1 |
| 7 | 4117 122 9402 | Plug | 1 |
| 8 | 1128 129 0906 | Gasket | 1 |
| 9 | 4116 121 4700 | Metering diaphragm | 1 |
| 10 | 1128 121 0801 | End cover | 1 |
| 11 | 1121 122 7101 | Screw | 4 |
| 12 | 4116 121 4800 | Pump diaphragm | 1 |
| 13 | 4116 129 0902 | Gasket | 1 |
| 14 | 1127 121 0800 | End cover | 1 |
| 15 | 1114 122 7100 | Screw | 1 |
| 16 | 1127 122 3200 | Torsion spring | 1 |
| 17 | 1127 120 7100 | Throttle shaft with lever | 1 |
| 18 | 1117 122 9000 | E-clip | 1 |
| 19 | 1133 121 3301 | Throttle shutter | 1 |
| 20 | 1115 122 7400 | Round head screw | 1 |
| 21 | 1127 122 3205 | Torsion spring | 1 |
| 22 | 1127 120 7200 | Choke shaft with lever | 1 |
| 23 | 1123 122 9000 | E-clip | 1 |
| 24 | 1122 121 2900 | Choke shutter | 1 |
| 25 | 1110 122 7400 | Round head screw | 1 |
| 26 | 1127 122 6201 | Idle speed adjustment screw | 1 |
| 28 | 1128 122 6703 | High speed adjustment screw Fitment / change note → | 1 |
| 29 | 1127 122 6800 | Low speed adjustment screw | 1 |
| 30 | 4203 122 3600 | Sealing ring | 1 |
| 31 | 1114 121 7800 | Strainer | 1 |
| 32 | 1122 121 7700 | Clamp | 1 |
| 33 | 1120 121 5600 | Fixed jet 0.56 Fitment / change note → | 1 |
| 33 | 1127 121 5602 | Fixed jet 0.58 Fitment / change note → | 1 |
| 34 | 1130 121 5600 NLA | Fixed jet 0.54 option | 1 |
| 35 | 4203 121 2700 | Cap Fitment / change note → | 2 |
| 36 | 5910 890 4500 | Puller Fitment / change note → option | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 1127 120 0604 | Carburetor HD-18C Fitment / change note → | 1 |
| — | 1127 120 0605 | Carburetor HD-21C Fitment / change note → | 1 |
| — | 1127 007 1062 | Set of carburetor parts | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Conditional replacement · 029 / 039
029 / 039 EPA: HD18A and HD21A remain model-specific
029 uses HD18A with jet 56; 039 uses HD21A with jet 58.
- Historical TI46/1997 guidance for the named 029/039 configurations only, not MS successors or every shared-sheet variant. No hardware operation was performed.
- Page 3 deletes HD5 1127 120 0601 in favor of 029 HD18A 1127 120 0604 and 039 HD21A 1127 120 0605. Page 7 explicitly restricts these branches to EPA machines; HD19A for non-EPA machines is separate.
- New valve jet 1128 121 5403 optimizes part-load running. Semi-fixed full-load jets: 029 uses 1120 121 5600 (Ø0.56, table fixed jet 56); 039 uses 1127 121 5602 (Ø0.58, fixed jet 58). Do not swap jets based on a shared sheet.
- Figure 3.2 items 1–6: caps limit H/L travel; knurled H and L screw heads hold caps; O-rings seal screws to carburetor body; insert bore lugs restrict cap movement; end cover has compensator stub. These figure numbers are not the page 7 parts-table numbers.
- Page 7: HD18A includes items 3–6,10,14–16,18; HD21A includes 3–6,10,14,15,17,18. Common new H screw 1128 122 6703 and L screw 1127 122 6801 each include item 10 sealing ring, which is NOT separately available. Two caps 4203 121 2700. All other parts as HD19 carburetor.
- The later IPL calls the same assembly numbers HD18C/HD21C. TI46 explicitly says A; reused numbers do not establish that every later internal setting/part is identical. No introduction serial supplied.
Source: TI 46/1997, p. 3 · TI 46/1997, p. 6 · TI 46/1997, p. 7 — Section 3.2 function and 3.5 EPA assembly/component rows.
Part numbers (9)
- 1127 120 0601 — Original HD5 carburetorEPA branch · Only model/configuration stated in conditions
- 1127 120 0604 — 029 EPA HD18A carburetorEPA branch · Only model/configuration stated in conditions
- 1127 120 0605 — 039 EPA HD21A carburetorEPA branch · Only model/configuration stated in conditions
- 1128 121 5403 — Valve jetEPA branch · Only model/configuration stated in conditions
- 1120 121 5600 — 029 jet 56EPA branch · Only model/configuration stated in conditions
- 1127 121 5602 — 039 jet 58EPA branch · Only model/configuration stated in conditions
- 1128 122 6703 — Item 14 H screw including sealing ringEPA branch · Only model/configuration stated in conditions
- 1127 122 6801 — Item 15 L screw including sealing ringEPA branch · Only model/configuration stated in conditions
- 4203 121 2700 — Item 18 limiter cap, twoEPA branch · Only model/configuration stated in conditions
Service note · 029 / 039
029 / 039 EPA: capped standard setting uses the lean stop
H 3/4 and L 1/4 open from the lean stop, within the 270° cap range.
- Historical TI46/1997 guidance for the named 029/039 configurations only, not MS successors or every shared-sheet variant. No hardware operation was performed.
- For the described HD18A/HD21A EPA system, factory optimum equals the owner-manual standard: H3/4 turn open and L1/4 turn open, each STARTING FROM THE LEAN STOP. This is not the uncapped screw-seat basic setting.
- Both caps allow 270° travel limited by insert lugs. Intended to permit leaner high-altitude correction while preventing enrichment beyond stated EPA limits.
- Only if running unsatisfactorily at higher altitude: check standard setting, warm engine, then turn H and L clockwise (leaner) as needed within permitted travel. Too lean a setting exceeds maximum permissible engine speed and can damage the engine. No numeric maximum speed is provided in this TI; do not invent one.
Source: TI 46/1997, p. 4 — Section 3.2.1 complete, both 270° arcs and altitude warning.
No additional parts-table entry added.
Service note · 029 / 039
029 / 039 EPA: cap removal, uncapped basic setting and new-cap alignment
Both screws open one full turn from their seats before new caps are seated flush.
- Historical TI46/1997 guidance for the named 029/039 configurations only, not MS successors or every shared-sheet variant. No hardware operation was performed.
- For screw replacement or carburetor cleaning, rotate limiter caps/adjusting screws COUNTERCLOCKWISE to stop. Screw puller 5910 890 4500 COUNTERCLOCKWISE into each cap until it comes off. Removed caps are damaged and MUST NOT be reused.
- After fitting adjusting screws and with caps OFF, start with screws against their seats: open H ONE FULL TURN and L ONE FULL TURN. This differs from capped H3/4, L1/4 measured from lean stops.
- Insert NEW caps in the illustrated lug positions (page 5 arrows show lower-left H lug and lower-right L lug in the printed front view); use the original diagram, not an inferred interchangeable orientation. Push caps onto screws until flush with insert 1. The resulting cap/screw position equals the standard setting. No re-use or unrestricted adjustment implied.
Source: TI 46/1997, p. 4 · TI 46/1997, p. 5 · TI 46/1997, p. 7 — Section 3.2.2 including removal and lug-position drawings; section 3.5 item 18 cap number.
Part numbers (2)
- 5910 890 4500 — Counterclockwise cap pullerServicing item · Described HD18A/HD21A EPA caps
- 4203 121 2700 — New limiter capsServicing item · Described HD18A/HD21A EPA caps
Service note · 029 / 039
029 / 039 EPA: tachometer idle, 50:1 evidence and TI27 gap
Idle is 2,800 rpm; EPA approval uses 50:1 with no emission measurements stated for other ratios.
- Historical TI46/1997 guidance for the named 029/039 configurations only, not MS successors or every shared-sheet variant. No hardware operation was performed.
- Set idle to 2,800 rpm with idle-speed screw LA; USE A TACHOMETER. LA is distinct from mixture screws H and L.
- EPA approval was obtained with 50:1 fuel/oil mix. The TI explicitly says no emission measurements are available for other mix ratios; it does not establish equivalence for another ratio.
- The cover says machines conforming to the modified standard receive the factory engine-information label, showing U.S. EPA Phase 1 for utility/lawn/garden engines and directing maintenance/adjustment to the owner manual. Blank family/type/displacement/date fields in the specimen are not an actual machine identity or universal production cutoff.
- TI27/1997 is delegated for emissions and Federal Emission Control Systems Utility Engines. It is absent from the retained 690TIs and current 766-PDF resource filename inventory. This is a documented bounded source gap; no missing warranty/emission-system text has been invented.
Source: TI 46/1997, p. 1 · TI 46/1997, p. 5 — Cover EPA label and sections 3.2.2.1–3.2.4.
No additional parts-table entry added.
Wrong number or missing part for the 029, 039? Report a correction →