← 029/039 · MS 290/310/390

Stihl 1127 · Section M · 12 of 13 · 39 parts

Carburetor HD-18C, HD-21C

Fits MS 290, MS 310, MS 390.

Parts diagrams →

Historical fitment & changes (2) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
11011121314151617181922021222324252628293303031323334353536456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (39)

PosPart numberDescriptionQty
1 4116 121 5100 Inlet needle 1
2 4116 121 5000 Inlet control lever 1
3 4116 122 3002 Spring 1
4 1113 121 9200 Spindle 1
5 1114 122 7400 Round head screw 1
6 1128 121 5403 Valve jet 1
7 4117 122 9402 Plug 1
8 1128 129 0906 Gasket 1
9 4116 121 4700 Metering diaphragm 1
10 1128 121 0801 End cover 1
11 1121 122 7101 Screw 4
12 4116 121 4800 Pump diaphragm 1
13 4116 129 0902 Gasket 1
14 1127 121 0800 End cover 1
15 1114 122 7100 Screw 1
16 1127 122 3200 Torsion spring 1
17 1127 120 7100 Throttle shaft with lever 1
18 1117 122 9000 E-clip 1
19 1127 121 3301 Throttle shutter 1
20 1115 122 7400 Round head screw 1
21 1127 122 3205 Torsion spring 1
22 1127 120 7200 Choke shaft with lever 1
23 1123 122 9000 E-clip 1
24 1122 121 2900 Choke shutter 1
25 1110 122 7400 Round head screw 1
26 1127 122 6201 Idle speed adjustment screw 1
28 1128 122 6703 High speed adjustment screw 1
29 1127 122 6800 Low speed adjustment screw 1
30 4203 122 3600 Sealing ring 1
31 1114 121 7800 Strainer 1
32 1122 121 7700 Clamp 1
33 1120 121 5600 Fixed jet 0.56 1
33 1127 121 5602 Fixed jet 0.58 1
34 1130 121 5600 NLA Fixed jet 0.54 option 1
35 4203 121 2700 Cap Fitment / change note → 2
36 5910 890 4500 Puller Fitment / change note → option 1
Not numbered on the diagram — assemblies, kits and options
— 1127 120 0604 Carburetor HD-18C 1
— 1127 120 0605 Carburetor HD-21C 1
— 1127 007 1062 Set of carburetor parts 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Conditional replacement · MS 290 / MS 310 / MS 390

MS 290 / MS 310 / MS 390: revised limiter cap keeps the same number

Limiter cap 4203 121 2700 and the carburetor retain their part numbers despite revised cap/segment geometry; number alone does not identify the old or new cap.

Later reviewed guidance: MS 290 / MS 310 / MS 390: square-bit driver for fitted limiter caps

  • Limiter cap 4203 121 2700 and the carburetor retain their part numbers despite revised cap/segment geometry; number alone does not identify the old or new cap.
  • The new cap has no upper detent, adds an alignment mark and moves the lug from perpendicular to the screw slot into line with it.
  • These models are explicitly named in the marked-segment subset. The L cap must not simply be pulled off at its stop: use the source’s quarter-turn offset and slot, groove, visible-lug and mark alignment.
  • The segment drawing gives previous groove width 1.19 mm and revised width 1.50 mm; these identify the illustrated revision, not a machining instruction or universal service tolerance.
  • H and L removal have separate alignment instructions. Puller 5910 890 4500 has a left-hand engagement thread; this note is not a complete carburetor removal or calibration procedure.
  • Removed limiter caps must not be reused because removal damages them. Replace caps after screw replacement or carburetor cleaning; no permanent cap-removal modification is implied.
  • Applies only to the named models with limiter cap 4203 121 2700. A shared catalog sheet is not approval for its other models or C/L variants. The sheet may contain uncapped versions; verify the actual carburetor configuration.
  • Retained edition: English USA. Introduction is continuous, with no numeric serial cutoff. Historical availability is not current stock or universal regional applicability.

Source: TI 21/2005, p. 1 · TI 21/2005, p. 2 · TI 21/2005, p. 3 · TI 21/2005, p. 4 — Sections 1–5: named-model cap revision; cover list distinguished from marked-segment subset.

Part numbers (2)
  • 4203 121 2700 — Limiter capUnchanged number, revised geometry · Named models using 4203 121 2700; single-use after removal
  • 5910 890 4500 — Limiter-cap pullerService tool · Left-hand engagement; separate H/L alignment

Conditional replacement · MS 290 / MS 310 / MS 390

MS 290 / MS 310 / MS 390: square-bit driver for fitted limiter caps

Screwdriver 5910 890 2304 is specified for carburetors using limiter cap 4203 121 2700; its square bit reaches the adjusting screw through the fitted cap.

  • Screwdriver 5910 890 2304 is specified for carburetors using limiter cap 4203 121 2700; its square bit reaches the adjusting screw through the fitted cap.
  • Conditional on limiter cap 4203 121 2700 actually being fitted, not every carburetor or every model/variant on the shared catalog sheet. Model association comes from TI 21/2005 and the catalog cap row; TI 50/2006 specifies the tool by cap configuration.
  • The without-cap basic-setting illustration starts with adjusting screws closed to their seats. It does not supply a turn count or extend the illustrated H/L arrangement to every carburetor on this sheet.
  • The source distinguishes initial engagement at the first detent from final fully-home seating after the series-specific basic setting. Do not treat the first detent as the completed installation.
  • Required idle/high-speed settings depend on the exact series; this bulletin supplies no universal screw-turn or RPM setting. Later series-specific service guidance still governs.
  • Caps removed to service an adjusting screw or clean the carburetor must not be reused. TI 21/2005 supplies the removal dependency; this is not authorization for permanent limiter removal.
  • Retained edition: English USA. Introduction is continuous, with no numeric serial cutoff. Historical availability is not current stock or universal regional applicability.

Source: TI 50/2006, p. 3 · TI 50/2006, p. 4 · TI 50/2006, p. 5 — Sections 3–3.4 and summary: capped-carburetor service tool and seating stages.

Part numbers (2)
  • 5910 890 2304 — Square-bit carburetor screwdriverService tool · Carburetors using 4203 121 2700 fitted caps
  • 4203 121 2700 — Limiter capExact tool configuration · New caps; final seating after series-specific basic setting

Wrong number or missing part for the MS 290, MS 310, MS 390? Report a correction →