Stihl 1128 · Section G · 7 of 13 · 30 parts
Tank housing
Fits MS 440.
Historical fitment & changes (2) — includes parts and conditions not shown on this drawing.
Parts (30)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 1128 350 0844 | Tank housing | 1 |
| 2 | 1128 122 6606 | Collar screw | 2 |
| 3 | 1128 358 7703 | Hose | 1 |
| 4 | 0000 350 5800 | Tank vent Fitment / change note → → replaced by 0000 350 5804 TI 41/2003 | 1 |
| 5 | not sold separately | O-ring not available as a separate item | 1 |
| 6 | 0000 967 3662 | Warning pictogram MS | 1 |
| 7 | 0000 967 3605 | Warning pictogram Filler cap | 1 |
| 8 | 1128 180 0910 | Switch shaft | 1 |
| 9 | 0000 997 0227 | Compression spring | 1 |
| 10 | 1128 182 1700 | Slide control | 1 |
| 11 | 1128 180 3501 | Switch housing | 1 |
| 12 | 1128 442 1600 | Contact spring | 1 |
| 13 | 1128 442 1601 | Contact spring | 1 |
| 14 | 9099 021 1760 | Self-tapping screw 2.9x9.5 | 1 |
| 15 | 0000 350 3504 | Pickup body | 1 |
| 16 | 1128 141 8600 | Impulse hose | 1 |
| 17 | 0000 350 0525 | Filler cap | 1 |
| 18 | 9645 948 7734 | O-ring 25x3.5 | 1 |
| 19 | 1128 182 1005 | Throttle trigger | 1 |
| 20 | 1128 182 1500 | Throttle rod | 1 |
| 21 | 1117 182 4500 | Torsion spring | 1 |
| 22 | 9371 470 2640 | Cylindrical pin 5x24 | 1 |
| 23 | 1117 182 0805 | Lockout lever | 1 |
| 24 | 1128 791 0600 | Handle molding | 1 |
| 25 | 9074 478 3076 | Pan head self-tapping screw IS-P4x19 | 1 |
| 26 | 1128 656 1500 | Guard Fitment / change note → | 1 |
| 27 | 9099 021 2770 | Self-tapping screw 3.9x13 Fitment / change note → | 1 |
| 28 | 0000 967 3500 NLA | Instruction label | 1 |
| 29 | 0000 967 3405 | Instruction label no longer available from factory | 1 |
| 30 | 0000 967 4056 | Warning Spark arresting screen | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Conditional replacement · MS 440
MS 440 transition: integrated vent and pressure equalization
TI 06/2001 describes the revised MS 440 vent and retains older vent parts for older machines, not as separately orderable new internals.
- Tank vent 1128 350 5802 → 0000 350 5800 in the revised MS 440 tank configuration.
- 1110 353 1600 and 1122 358 1800 are the previous valve and filter, not new separately orderable internals for 0000 350 5800.
- The new valve/filter versions are marked unavailable separately. Old vent, valve and filter remain available for older machines in this historical source.
- This transition concerns the revised MS 440 tank and the matched-housing repair described for 044; it does not prove a vent-only retrofit to every old tank.
- Construction drawing 176TI005 KN labels the perforated sheet/diaphragm (1), air-side filter (2), tank-side filter (3), and integral protective cap (4). These are local drawing labels, not summary-table item numbers. The exploded illustration explains construction; it does not make the new internals separately serviceable or orderable.
- Function drawings 176TI006/007 KN use different local labels: air side (1), fuel-tank side (2), diaphragm (3), valve plate (4). With equal pressures, the spring presses the diaphragm against the plate and closes the valve. Fuel withdrawal initially creates a vacuum, lifting the diaphragm from the plate so air enters the tank. The valve closes again when pressures equalize.
- This is a qualitative inlet-vent explanation, not an overpressure-relief specification or a pressure/vacuum test procedure. No opening-pressure threshold, leak limit or disassembly/repair procedure is supplied. Summary item 3 includes items 4 and 5; the new valve and filter are marked -*- and unavailable separately, not assigned the old component numbers.
- Introduction is in progress without a numeric serial cutoff; retained edition is english / USA. Earlier model- and dome-dependent retrofit restrictions are not erased.
Source: TI 6/2001, p. 1 · TI 6/2001, p. 2 · TI 6/2001, p. 3 · TI 6/2001, p. 4 — Complete sections 1–9: 044/MS440 naming and power chronology, split-filter intake, cap operation, matching assemblies, vent construction/function, main bearing, clutch and all 17 summary rows.
Part numbers (4)
- 1128 350 5802 — Tank ventPrevious version · Previous tank configuration
- 0000 350 5800 — Integrated tank ventNew version · Revised MS 440 tank configuration
- 1110 353 1600 — ValvePrevious vent component · Older vent only; not a new vent service part
- 1122 358 1800 — FilterPrevious vent component · Older vent only; not a new vent service part
Historical fitment · MS 440
MS 440: tank guard starts at serial 1 57 629 100
Guard and mounting screw are ordered separately from tank housing 1128 350 0832.
1 57 629 100 — MS 440 tank guard standard from this serial; not model identification or an earlier-machine retrofit claim.
- MS 440 tank housing comes standard with guard 1128 656 1500 from serial 1 57 629 100. Screw 9099 021 2770 secures the guard; drawing 175 TI 003 identifies guard (1) and screw (2) beneath the housing.
- Replacement tank housing 1128 350 0832 does NOT include the guard or screw: order both separately. Standard production equipment does not mean included replacement-housing contents.
- This is an MS 440 equipment changeover, not an MS 440 identity interval or blanket 044/046/MS 460 retrofit approval. No earlier-machine interchangeability or screw torque is stated. TI 28/2002 is a previous-issue pointer, not an installation dependency.
- This is historical source guidance, not current stock information or universal machine fitment. No physical interchange test was performed.
Source: TI 11/2003, p. 1 — Complete bulletin: guard, drawing175TI003, summary and availability.
Part numbers (3)
- 1128 656 1500 — Tank housing guardSeparate order · MS 440; stated tank housing
- 9099 021 2770 — Guard mounting screwSeparate order · MS 440 tank guard
- 1128 350 0832 — Tank housingExcludes guard and screw · MS 440
Wrong number or missing part for the MS 440? Report a correction →