← 044/046 · MS 440/460/461

Stihl 1128 · Section K · 10 of 16 · 29 parts

AV system

Fits MS 460.

Parts diagrams →

Historical fitment & changes (1) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
11011121314151617181922021222324252634445667789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (29)

PosPart numberDescriptionQty
1 1128 791 8401 Ring 1
2 1128 791 8400 Ring 1
3 1122 790 9905 Annular buffer 1122/05 1
4 9074 478 4435 Pan head self-tapping screw IS-P6x19 3
5 1122 791 7301 Plug 1
6 1121 790 9904 Annular buffer 2
6 1125 790 9906 Annular buffer 1125/06 2
7 1125 791 7306 Plug 2
8 1128 790 9909 Annular buffer 1
8 1128 790 9908 Annular buffer 1
9 9416 868 5630 Hollow rivet 5.5x0.5x6.8 2
10 9022 313 0680 Spline screw IS-M4x16 2
11 1128 791 7200 Sleeve 1
12 1128 792 8500 Hose 1
13 9074 478 4675 Pan head self-tapping screw IS-P6x32.5 1
14 1125 790 9910 Annular buffer 1125/10 1
15 1125 790 9904 Annular buffer 1125/04 1
16 1128 790 9911 Annular buffer 1
17 1133 791 5900 Stop buffer 1
18 1128 141 8600 Impulse hose 1
19 1110 145 9001 Plug 1
20 1117 141 1800 Sleeve 1
21 1128 121 8600 Washer 1
22 1128 120 0624 Carburetor HD-14B 1
22 1128 120 0626 Carburetor HD-24C 1
23 1128 120 0623 Carburetor HD-16B 1
24 1128 121 7000 Baffle 1
25 1128 182 0700 Grommet 1
26 1128 123 7502 Grommet 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · MS 440 / MS 460 / MS 361 / MS 361 C

Stop buffer 1124 791 2800: unchanged number, conflicting increment

The printed 0.0078-inch increase does not equal 2 mm.

  • Stop buffer 1124 791 2800 is modified for improved guidance and rigidity WITHOUT AN ORDER-NUMBER CHANGE. The arrow marks dimension a across the illustrated buffer; the source prints increase “0.0078 in (2 mm)” to “0.97 in (24,7 mm)”.
  • CONFLICT: 0.0078 inch is about 0.198 mm, not 2 mm; 2 mm is about 0.0787 inch. Both printed increment values are retained; no corrected increment or old dimension is asserted. The nominal new dimension remains the printed 0.97 in (24.7 mm), not a manufacturing tolerance or permission to machine an old buffer.
  • Continuous introduction, no serial cutoff. The summary says only the modified version is factory-available; other individual parts remain unchanged. An unchanged part number alone cannot identify old versus modified stock. The note does not state a general fitment claim for every model that ever used this number.
  • Historical TI36/2005 English USA guidance only; the linked catalog sheets are navigation anchors, not proof that all later variants share these specifications. No physical interchange test was performed.

Source: TI 36/2005, p. 2 · TI 36/2005, p. 3 — Stop buffer 1124 791 2800: unchanged number, conflicting increment.

Part numbers (1)
  • 1124 791 2800 — Stop bufferModified geometry, unchanged number; unit conflict · MS 440, MS 460, MS 361, MS 361 C; see note restrictions

Wrong number or missing part for the MS 460? Report a correction →