← 020 T · MS 200 · MS 200 T

Stihl 1129 · Section K · 9 of 12 · 18 parts

Air filter 020

Fits 020.

Parts diagrams →

Historical fitment & changes (3) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
11011121314151616171823456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (18)

PosPart numberDescriptionQty
1 1129 120 1603 Air filter 1
2 1129 120 1604 Air filter, fleece 1
3 1129 124 3400 Filter base 1
4 1129 140 1903 Carburetor box cover 1
5 1129 141 2300 Twist lock 1
6 1129 967 1505 Model plate 020 T, 020 1
7 1129 120 0650 Carburetor C1Q-S32 1
8 1129 123 7504 Grommet → replaced by 1129 123 7507 TI 20/2003 1
9 9216 261 0700 Hexagon nut M5 2
10 1113 141 1805 Sleeve 1
11 1129 121 8600 Washer 1
12 1129 141 2201 Manifold 1
13 1129 141 3300 Supporting plate 1
14 1129 790 9900 Annular buffer 1
15 9022 313 0680 Spline screw IS-M4x16 2
16 1129 791 6100 Screw 2
17 1129 790 9903 Annular buffer 1
18 9104 003 3004 Self-tapping screw P4x14 2

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · 020

020 compensator: the connecting channel also guides adjusting screws

Do not adjust the high-speed screw merely because the filter is getting dirtier.

  • The connecting channel between carburetor and air filter doubles as a grommet that protects and guides the carburetor adjusting screws. Figure 144TI002 SC points to this channel; it is not a dimensioned fabrication drawing.
  • The TI describes the compensator as keeping fuel content constant as the filter becomes contaminated, preventing the mixture becoming over-rich for that reason. It says changing the high-speed screw setting as the filter gets dirtier is no longer necessary. This is not a guarantee against every rich-running fault, permission to ignore power loss, or a supplied calibration/adjustment procedure.
  • The bulletin refers to TI07/1991 (STIHL 066) for a more detailed operating explanation. That exact TI is absent from the retained bulletin corpus and bounded STIHL service documentation filename/document inventory. This named source gap does not justify importing 066 parts or inventing a compensator pressure schematic.
  • Applies to the rear-handle 020 introduced in TI10/1997, series 1129; not the earlier 020 generation, 020 T or MS 200 by name similarity. No production serial cutoff, universal retrofit, tested interchange or current supply claim. No hardware operation was performed.

Source: TI 10/1997, p. 2 — 020 compensator: the connecting channel also guides adjusting screws.

No additional parts-table entry added.

Service note · 020

020 carburetor: compensator stub, dual choke attachment and sealed screws

Changed orientation and end cover do not identify a carburetor model or authorize a 020 T swap.

  • Compared with 020 T, the metering-chamber end cover has a connecting stub for the compensator. The choke-shaft lever has a dual attachment point for 020 and 020 T, and the adjusting screws are sealed with an O-ring.
  • Carburetor position is adapted to the different handle system. A dual attachment point does not establish complete carburetor interchange, a shared adjustment or identical manifolds.
  • No carburetor maker/type, assembly number, O-ring size, screw setting or pressure-test value is printed in this TI. The linked later IPL air-filter sheet names C1Q-S32, but that later identity is not silently projected onto the unnamed 1997 carburetor; neither WT-326D nor another 020 T carburetor is inferred.
  • Applies to the rear-handle 020 introduced in TI10/1997, series 1129; not the earlier 020 generation, 020 T or MS 200 by name similarity. No production serial cutoff, universal retrofit, tested interchange or current supply claim. No hardware operation was performed.

Source: TI 10/1997, p. 2 — 020 carburetor: compensator stub, dual choke attachment and sealed screws.

No additional parts-table entry added.

Service note · 020

020 round air filter: lift, withdraw and positively refit the end cover

Tool-free hooks and compensator-stub alignment belong to the rear-handle round filter.

  • The large-area round element has a compensator connecting stub. The source describes high retention, long service life and easy handling, but gives no numerical efficiency or hour interval. Cleaning becomes necessary when there is a noticeable loss of engine power.
  • After removing the carburetor-box cover, lift the filter slightly and pull it away to the rear; snap-on hooks hold it on the base and removal needs no tools. To clean inside, remove the filter end cover by pressing the OTHER END of the element against a firm, flat base. Refit the cover until it SNAPS INTO PLACE.
  • On refitting, the compensator stub locates automatically in the connecting channel; engage the snap-on hooks with slight pressure. Drawings 144BA010 KN and 144BA019 KN show withdrawal and end-cover movement, not filter crushing or hammering.
  • No filter material, oiling instruction, solvent, air pressure, replacement part number or cleaning interval is specified here. Do not import the different 020 T filter procedure or unrelated HD/foam treatment. Later IPL alternatives do not establish the original element material.
  • Applies to the rear-handle 020 introduced in TI10/1997, series 1129; not the earlier 020 generation, 020 T or MS 200 by name similarity. No production serial cutoff, universal retrofit, tested interchange or current supply claim. No hardware operation was performed.

Source: TI 10/1997, p. 3 — 020 round air filter: lift, withdraw and positively refit the end cover.

No additional parts-table entry added.

Wrong number or missing part for the 020? Report a correction →