Stihl 1129 · Section J · 8 of 12 · 31 parts
Handle housing 020
Fits 020.
Historical fitment & changes (2) — includes parts and conditions not shown on this drawing.
Parts (31)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 1129 790 1001 | Handle housing → replaced by 1129 790 1013 TI 20/2003 | 1 |
| 2 | 1125 122 6600 | Collar screw | 2 |
| 3 | 1129 182 0901 | Switch shaft | 1 |
| 4 | 1129 442 1600 | Contact spring | 1 |
| 5 | 1129 180 1501 | Throttle trigger | 1 |
| 6 | 1129 182 4500 | Torsion spring | 1 |
| 7 | 1129 182 0801 | Lockout lever | 1 |
| 8 | 1129 182 1502 | Throttle rod | 1 |
| 9 | 1129 185 1902 | Choke rod | 1 |
| 10 | 1129 185 2001 | Choke lever | 1 |
| 11 | 1129 791 1701 | Handlebar | 1 |
| 12 | 9074 478 4675 | Pan head self-tapping screw IS-P6x32.5 | 1 |
| 13 | 1116 790 9600 | Annular buffer | 1 |
| 14 | 9022 341 0960 | Spline screw IS-M5x12 → replaced by 9022 341 0980 TI 3/2006 | 1 |
| 15 | 1129 791 0601 | Handle molding | 1 |
| 16 | 9104 003 3004 | Self-tapping screw P4x14 | 3 |
| 17 | 1129 790 9700 | Stop buffer | 1 |
| 18 | 1129 791 6101 | Collar screw | 1 |
| 19 | 9074 478 4435 | Pan head self-tapping screw IS-P6x19 | 1 |
| 20 | 1129 791 7500 | Cover | 1 |
| 21 | 1129 793 3000 | Slide | 1 |
| 22 | 9099 021 1760 | Self-tapping screw 2.9x9.5 | 1 |
| 23 | 1129 440 3000 | Wiring harness | 1 |
| 24 | 0751 030 8950 NLA | Terminal socket A 4-1 no longer available from factory | 1 |
| 25 | 0751 030 8452 | Spade terminal 4.8-1 no longer available from factory | 1 |
| 27 | 0000 989 0814 | Grommet | 1 |
| 28 | 0000 989 0813 NLA | Grommet | 1 |
| 29 | 0751 030 8474 | Terminal socket 4.8-1 no longer available from factory | 1 |
| 30 | 0751 030 8490 | Terminal socket 3.5 no longer available from factory | 1 |
| 31 | 0000 967 3500 NLA | Instruction label | 1 |
| 32 | 0000 967 3662 | Warning pictogram MS | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · 020
020 winter shutter: use preheating below about 10 °C
Return to summer position above about 10 °C to avoid running problems.
- Heated cooling air flows over the carburetor and is drawn through the filter as preheated combustion air, helping prevent filter and carburetor icing in cold conditions.
- The new tank housing and carburetor box (handle frame) provide cutout 1, opened or closed by shutter 2. Figure 144TI003 SC identifies those two features; the numerals are figure labels, not part numbers.
- Activate intake-air preheating ONLY BELOW APPROXIMATELY 10 °C. Change back to the SUMMER POSITION ABOVE ABOUT 10 °C to avoid engine-running problems. The threshold is approximate; no exact-at-10 rule, automatic thermostat, universal winter kit, shutter-fastener torque or new screw identity is supplied.
- Applies to the rear-handle 020 introduced in TI10/1997, series 1129; not the earlier 020 generation, 020 T or MS 200 by name similarity. No production serial cutoff, universal retrofit, tested interchange or current supply claim. No hardware operation was performed.
Source: TI 10/1997, p. 3 — 020 winter shutter: use preheating below about 10 °C.
No additional parts-table entry added.
Service note · 020
020 handle fasteners: keep 5.3, 5.5 and 2.0 Nm distinct
These three rear-handle values are the exceptions to the 020 T torque baseline.
- Plastorm screw P 6x32.5, FRONT HANDLE TO HANDLE FRAME: 5.3 Nm. Spline screw, STOP BUFFER TO TANK HOUSING: 5.5 Nm. Collar screw P 5, HANDLE FRAME (REAR HANDLE) TO STOP BUFFER: 2.0 Nm.
- Only torques differing from 020 T are printed here; the TI calls all others identical. It does not give a full fastener part number, the spline-screw dimensions, an adhesive requirement, or a reused-thread torque reduction for these three exceptions. Do not assign the later IPL number simply by proximity.
- The available 020 T manual has copyright 1999 and a separate model-specific torque table. In particular its front-handle/handle-housing P6x21.5 row is a DIFFERENT fastener from the TI P6x32.5 row. Do not replace the 020 values with 020 T values or borrow its footnotes without exact joint evidence. All 29 later-table rows and their footnotes are now reviewed separately in the later 020 T notes below; this does not make them rear-handle 020 exceptions.
- Applies to the rear-handle 020 introduced in TI10/1997, series 1129; not the earlier 020 generation, 020 T or MS 200 by name similarity. No production serial cutoff, universal retrofit, tested interchange or current supply claim. No hardware operation was performed.
Source: TI 10/1997, p. 4 — 020 handle fasteners: keep 5.3, 5.5 and 2.0 Nm distinct.
No additional parts-table entry added.
Wrong number or missing part for the 020? Report a correction →