← 020 T · MS 200 · MS 200 T

Stihl 1129 · Section M · 11 of 12 · 36 parts

Carburetor WT-326D

Fits 020 T, 020.

Parts diagrams →

Historical fitment & changes (1) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
110111213141516171819220212223242526272829330313233343556789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (36)

PosPart numberDescriptionQty
1 1129 121 5402 Valve jet 1
2 4117 122 9402 Plug 1
3 1129 121 5600 Fixed jet 0.50 1
5 4116 121 5100 Inlet needle 1
6 4116 122 3000 Spring 1
7 1113 121 5000 Inlet control lever 1
8 1113 121 9200 Spindle 1
9 1114 122 7400 Round head screw 1
10 1120 129 0900 Gasket 1
11 1129 121 4700 Metering diaphragm 1
12 1113 121 0800 End cover 1
13 1106 122 7400 Round head screw 4
14 1114 121 7800 Strainer 1
15 1121 121 4801 Pump diaphragm 1
16 1120 129 0905 Gasket 1
17 1129 121 0801 End cover 1
18 1114 122 7100 Screw 1
19 not sold separately Ball not available as a separate item 1
20 not sold separately Idle speed adjustment screw not available as a separate item 1
21 1130 122 3200 Torsion spring 1
22 1129 120 7101 Throttle shaft with lever 1
23 1123 121 3301 Throttle shutter 1
24 1115 122 7400 Round head screw 1
25 1117 122 9000 E-clip 1
26 1123 122 6802 Low speed adjustment screw 1
27 1115 122 3002 Spring 1
28 1111 121 8605 Washer 1
29 4124 122 3600 Sealing ring 1
30 1129 122 3200 Torsion spring 1
31 1129 120 7202 Choke shaft with lever 1
32 1110 122 7400 Round head screw 1
33 1123 122 9000 E-clip 1
34 1130 121 2900 Choke shutter 1
35 1123 121 5642 Fixed jet 0.42 option 1
Not numbered on the diagram — assemblies, kits and options
— 1129 120 0606 Carburetor WT-326D Fitment / change note → → replaced by 1129 120 0651 TI 37/2000 1
— 1129 007 1061 Set of carburetor parts 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · 020 T

020 T WT 326: trim gasket and metering diaphragm flush

After repairs to carburetor 1129 120 0606, the illustrated protruding edges must be flush with the body.

  • After repairs to carburetor 1129 120 0606, always trim away the gasket AND metering diaphragm flush with the carburetor body. Figure 142TI010 KN shows the edge enlarged and a scissor-cut illustration; it does not prescribe a recess, depth or separate component part numbers.
  • The TI heading says WT 326 without a suffix; the retained later sheet labels 1129 120 0606 WT-326D. The part-number binding is explicit, but the TI is not evidence that every WT326 suffix is identical. Do not apply the trimming instruction to C1Q-S32, C1Q-S16A, pump diaphragms or all carburetors on the shared air-filter sheet.
  • TI 04/1999 USA names Model 020 T, series 1129. The broader extracted title and shared catalog labels do not extend these assertions to rear-handle 020, earlier series 1114, MC 200 or MS 200 successors. Factory availability is historical, not current stock; physical interchange has not been tested. No hardware operation was performed.

Source: TI 4/1999, p. 2 — Complete section3 service note and enlarged scissor detail142TI010 KN.

Part numbers (1)
  • 1129 120 0606 — WT 326 carburetor named by service noteRepair-specific gasket/metering-diaphragm trimming · 020 T; TI 04/1999 only

Wrong number or missing part for the 020 T, 020? Report a correction →