← 017/018 · MS 170/180

Stihl 1130 · Section B · 2 of 10 · 22 parts

Cylinder

Fits 018.

Parts diagrams →

Historical fitment & changes (2) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
1101011121213141515161617171819220202122344566789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (22)

PosPart numberDescriptionQty
1 1130 020 1208 Cylinder with piston Ø 38 mm — 31.8 cc 1
2 1130 020 1209 Cylinder with piston Ø 38 mm — 31.8 cc 1
3 1130 030 2004 Piston Ø 38 mm — 31.8 cc 1
4 1130 034 3002 Piston ring Ø 38x1.2 mm — 31.8 cc 2
5 1132 034 1501 Piston pin 10x6.5x25 1
6 9463 650 1000 Snap ring 10 2
7 1130 020 1203 Cylinder with piston Ø 38 mm → replaced by 1130 020 1205 TI 6/2000 — 31.8 cc 1
8 1130 020 1201 Cylinder with piston Ø 38 mm — 31.8 cc 1
9 1130 030 2003 Piston Ø 38 mm — 31.8 cc 1
10 1130 034 3002 Piston ring Ø 38x1.2 mm — 31.8 cc 2
11 1130 034 1500 Piston pin 8x4x25 → replaced by 1132 034 1501 TI 6/2000 1
12 9463 650 0807 Snap ring 8x0.7 2
13 1123 020 9400 Decompression valve 1
14 1132 030 0402 Crankshaft 1
15 9503 003 0311 Grooved ball bearing 6002 2
16 9638 003 1581 Oil seal 15x25x5 2
17 9639 003 1585 Oil seal 15x25x5 2
18 9468 621 1520 Circlip 15x1 1
19 1130 021 2505 Engine pan 1
20 9075 478 4159 Pan head self-tapping screw IS-D5x24 8
21 1110 400 7005 Spark plug Bosch WSR 6 F 1
22 0783 830 2000 Tube of sealant Dirko HT red 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · 018 / 018 C

018 and 018 C: launch equipment and engine design

The C version combines quick chain tensioning, ElastoStart and a decompression valve; those are not standard-version promises.

  • The 018 is described as a development of the 017, with the same applications. It is offered as standard 018 and 018 C; the latter has quick chain tensioner, ElastoStart and decompression valve. The cover photograph specifically shows an 018 C with Picco Micro Mini cutting attachment. Neither the photograph nor the shared family establishes those convenience features on every standard 018.
  • The descriptions cover only differences from the 017. The single-cylinder two-stroke engine has a machined crankshaft, described as optimizing the big-end bearing and high-speed characteristics, a four-port cylinder and a two-ring piston. The cylinder drawing 140TI002 KN illustrates the four-port mixture-flow arrangement; it supplies no port dimensions or machining instructions.
  • Improved mixture control, cleaner combustion and lower emissions are the bulletin’s design claims, not independent measurements. No crankshaft, cylinder or piston part numbers or 017-to-018 conversion instructions are supplied here.
  • Historical TI 42/1998, series 1130. This is the launch-era 018/018 C evidence, not a specification for MS 180 or every later 018 carburetor/configuration. No serial threshold, current stock or physically tested interchange is established. No hardware operation was performed.

Source: TI 42/1998, p. 1 · TI 42/1998, p. 2 — Complete introduction,cover photograph and section1 engine/cylinder/piston;140TI002 KN.

No additional parts-table entry added.

Service note · 018 / 018 C

018: 31.8 cm³ engine and 2,800 rpm idle specification

Launch specifications include a 38 mm bore, 1.4 kW power and 1.75 Nm maximum torque at 6,500 rpm.

  • Displacement is 31.8 cm³ (1.94 cu.in), bore 38 mm (1.5 in), and engine power to ISO 7293 is 1.4 kW (1.9 bhp). Maximum torque is 1.75 Nm (1.3 lb.ft) at 6,500 rpm. This is engine output torque, not a fastener-tightening torque.
  • Idle speed is 2,800 rpm. The main bearings are two deep-groove ball bearings; the big-end and small-end bearings are each described as a needle sleeve. No bearing dimensions or part numbers are specified.
  • The engine-idle specification is read together with section5.1: the chain must not rotate at idle. The 6,500 rpm torque point and 8,000 rpm ignition-timing condition are not maximum permitted engine speeds.
  • Historical TI 42/1998, series 1130. This is the launch-era 018/018 C evidence, not a specification for MS 180 or every later 018 carburetor/configuration. No serial threshold, current stock or physically tested interchange is established. No hardware operation was performed.

Source: TI 42/1998, p. 1 · TI 42/1998, p. 3 — Introduction and complete section2.1.

No additional parts-table entry added.

Wrong number or missing part for the 018? Report a correction →