Stihl 1132 · Section C · 3 of 9 · 27 parts
Hand guard, Chain brake
Fits 019 T.
Historical fitment & changes (2) — includes parts and conditions not shown on this drawing.
Parts (27)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 1132 792 9100 | Hand guard | 1 |
| 2 | 0000 967 3724 | Instruction label | 1 |
| 3 | 1128 160 5000 | Lever | 1 |
| 4 | 0000 958 0521 | Washer | 1 |
| 5 | 1123 162 5800 | Strap | 1 |
| 6 | 9460 624 0400 | E-clip 4 | 1 |
| 7 | 1123 162 7800 | Flat spring | 1 |
| 8 | 1123 162 7900 | Tension spring → replaced by 1123 162 7902 TI 46/2006 | 1 |
| 9 | 1132 160 5400 | Brake band | 1 |
| 10 | 9104 003 3005 | Self-tapping screw P4x20 | 1 |
| 11 | 1132 021 1101 | Cover | 1 |
| 12 | 1123 640 7105 | Worm → replaced by 1123 640 7102 TI 5/2005 | 1 |
| 13 | 1123 647 2400 | Spring | 1 |
| 14 | 1121 162 3201 | Carrier | 1 |
| 15 | 1129 162 0800 | Clutch shoe | 3 |
| 16 | 1127 162 3000 | Retainer | 3 |
| 17 | 0000 997 5515 | Tension spring | 3 |
| 18 | 1121 162 1001 | Cover washer | 1 |
| 19 | 1121 162 3205 | Carrier | 1 |
| 20 | 1121 162 3000 | Retainer | 3 |
| 21 | 1123 640 2000 NLA | Chain sprocket 3/8" Picco 7T | 1 |
| 21 | 1123 640 2003 | Chain sprocket 3/8" Picco 6T option | 1 |
| 21 | 1123 640 2010 NLA | Chain sprocket 1/4" 8T option | 1 |
| 22 | 9512 933 2260 | Needle cage 10x13x10 | 1 |
| 23 | 0000 958 1022 | Washer Ø 27 mm | 1 |
| 24 | 9460 624 0801 | E-clip 8x1.3 | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 1123 160 2050 | Clutch | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · 019 T
019 T: paired cutting attachments and standard seven-tooth drive
Picco-Micro-1 / Rollomatic or Picco-Micro-Narrow / Rollomatic Mini; standard 7-tooth 3/8 P, 0.16 l oil tank.
- The cover pairs 3/8-inch PICCO-MICRO-1 with ROLLOMATIC, OR 3/8-inch PICCO-MICRO-NARROW with ROLLOMATIC MINI. Section 2.6 lists the same chain/bar families. Do not turn the two explicit pairings into permission to mix either chain with either bar. No bar length, drive-link count, gauge or bar/loop ordering number is given.
- Section 2.6 literally prints chain pitch as 9.32 mm (3/8 inch) for Picco-Micro-Narrow, followed by 3/8-inch Picco-Micro 1. The stated 9.32 mm is NOT silently normalized to 9.525 mm (the arithmetic conversion of 3/8 inch). Retain the printed metric/inch discrepancy; it does not establish a separate chain standard.
- Standard sprocket: 7-TOOTH 3/8-inch P SPUR sprocket. Printed chain speed 21.7 m/s (71.2 ft/sec) at 10,000 rpm. Preserve the source values, not an independently measured performance or a calculated speed for the optional six-tooth sprocket.
- Chain lubrication: SPEED-CONTROLLED RECIPROCATING OIL PUMP; oil tank capacity 0.16 l (0.34 US pt). This does not assert a user-adjustable pump, flow rate or validated delivery at idle.
- Historical TI40/1996 introduction for 019 T, series 1132 only. Later 2012 catalog sheets are navigation anchors, not proof that every listed part is original 1996 equipment. No extension to MS 190 T or MS 191 T, serial cutoff or verified physical interchange. No hardware operation was performed.
Source: TI 40/1996, p. 1 · TI 40/1996, p. 4 — paired cutting attachments and standard seven-tooth drive.
No additional parts-table entry added.
Service note · 019 T
019 T: optional six-tooth sprocket and ElastoStart
Special accessories: 1123 640 2005 six-tooth 3/8 P spur sprocket and 0000 190 3400 ElastoStart.
- Section 3 lists SPECIAL ACCESSORIES FOR USER: 6-tooth 3/8-inch P spur sprocket 1123 640 2005 and ElastoStart 0000 190 3400. The six-tooth accessory is distinct from the standard SEVEN-tooth sprocket in section 2.6; no replacement/supersession relationship is asserted.
- Neither accessory number appears in the retained exact-019 T 2012 assembly rows. Historical assignments are carried as TI evidence on the relevant chain-drive and starter sheets, with no invented drawing position or claim of current catalog stock.
- No accessory installation sequence, included-kit list, changed rope length, required chain-loop length or measured effect on speed/starting effort is printed. The 1123 prefix does not broaden this TI’s 019 T assignment.
- Historical TI40/1996 introduction for 019 T, series 1132 only. Later 2012 catalog sheets are navigation anchors, not proof that every listed part is original 1996 equipment. No extension to MS 190 T or MS 191 T, serial cutoff or verified physical interchange. No hardware operation was performed.
Source: TI 40/1996, p. 4 — optional six-tooth sprocket and ElastoStart.
Part numbers (2)
- 1123 640 2005 — 6-tooth 3/8-inch P spur sprocketOptional user accessory, not standard 7-tooth sprocket · 019 T in TI40/1996 section 3
- 0000 190 3400 — ElastoStartOptional user accessory · 019 T in TI40/1996 section 3
Wrong number or missing part for the 019 T? Report a correction →