← 019 T · MS 190 T · MS 191 T

Stihl 1132 · Section B · 2 of 9 · 30 parts

Engine housing

Fits 019 T.

Parts diagrams →

Historical fitment & changes (7) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
1111213141415161718192202122232324252634404156789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (30)

PosPart numberDescriptionQty
1 1132 020 3050 Engine housing 1
2 1123 162 5205 Pin 1
3 1120 162 5200 Pin 1
4 1123 162 5200 Pin 1
5 1123 664 2400 Collar screw 1
6 1123 664 2402 NLA Collar screw 1
7 1123 791 2800 Annular buffer 2
7 1127 791 2800 Annular buffer 2
8 1132 791 7310 Plug 2
9 1132 791 7300 Plug 2
11 1123 640 3200 NLA Oil pump 0.55 1
12 1132 182 5501 Cover 1
13 1132 350 0400 Fuel tank Fitment / change note → 1
14 0747 313 6810 Valve Fitment / change note → 1
15 1132 358 7700 Hose Fitment / change note → 1
16 0000 350 3502 Pickup body 1
17 1132 350 4400 Oil tank 1
18 1132 647 9400 Hose 1
19 1123 640 3800 Pickup body 1
20 1132 350 0500 Filler cap 1
21 0000 359 1201 Sealing ring 1
22 4226 350 0900 Rope 1
23 0000 353 0605 Hook 1
24 1130 350 0500 Filler cap 1
25 0000 359 1240 Sealing ring 1
26 0000 350 0905 Rope 1
40 0000 989 0516 Grommet Fitment / change note → 1
41 4205 141 8601 Hose 325 mm / 12 13/16'' Fitment / change note → 1
Not numbered on the diagram — assemblies, kits and options
— not sold separately AV system normal:
— not sold separately AV system hard:

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · 019 T

019 T: top-handle purpose, reed-valve engine and AV design

1996 specialist tree-surgery saw; four transfer ports, reed valve, three-piece AV element and pull-out ring.

  • The cover describes a favorably priced TOP HANDLE saw for tree surgery and tree maintenance, developed for QUALIFIED AND PROPERLY TRAINED SPECIALISTS. This historical positioning and product photograph are not a general-use recommendation or a current price/availability claim.
  • Engine description: hemispherical combustion chamber with FOUR transfer ports in the cylinder (drawing 170TI001 KN); REED VALVE; high-volume carburetor air intake from the machine’s low-dust zone; durable MACHINED crankshaft. Section 2.1 separately calls the crankshaft durable BUILT-UP; both descriptions retained, not a claim of one-piece construction.
  • Muffler has a spark-arresting screen. Multi-part AV element is described as patented; drawing 170TI005 KN identifies 1 Plug, 2 Annular buffer, 3 Plug. These are figure callouts, not spare-part numbers, dimensions or assembly torques. Patent wording is a 1996 source statement, not current legal status.
  • Ergonomically curved handlebar with oval section; multifunction lever and SEPARATE choke lever for hot and cold starts. Page 3 drawing 170TI006 KN shows the PULL-OUT RING pivoting out from the housing. No load rating, fall-arrest function or lifting procedure is specified.
  • Historical TI40/1996 introduction for 019 T, series 1132 only. Later 2012 catalog sheets are navigation anchors, not proof that every listed part is original 1996 equipment. No extension to MS 190 T or MS 191 T, serial cutoff or verified physical interchange. No hardware operation was performed.

Source: TI 40/1996, p. 1 · TI 40/1996, p. 2 · TI 40/1996, p. 3 — top-handle purpose, reed-valve engine and AV design.

No additional parts-table entry added.

Service note · 019 T

019 T: powerhead weight and printed sound levels

3.9 kg without cutting attachment; 96 dB(A) Lpeq / ISO 7182 and 106 dB(A) Lweq / ISO 9207.

  • Section 2.4 powerhead WITHOUT CUTTING ATTACHMENT: 3.9 kg (8.6 lb). Power-to-weight ratio printed as 3.2 kg/kW (5.3 lb/bhp). Do not substitute calculated rounding or call this a ready-to-cut weight; fuel-fill state is not stated.
  • Section 2.5 is headed Sound / Vibration Levels, but prints ONLY sound values: continuous sound level Lpeq to ISO 7182, 96 dB(A); sound power level Lweq to ISO 9207, 106 dB(A). These are different quantities and standards, not two alternative measurements of the same sound level.
  • Both ISO lines carry a superscript 1) marker. No corresponding footnote text or vibration value is visible on any of the seven retained TI pages. Preserve that source omission; no averaging-cycle definition, uncertainty, vibration magnitude or modern-standard equivalence is supplied.
  • Historical TI40/1996 introduction for 019 T, series 1132 only. Later 2012 catalog sheets are navigation anchors, not proof that every listed part is original 1996 equipment. No extension to MS 190 T or MS 191 T, serial cutoff or verified physical interchange. No hardware operation was performed.

Source: TI 40/1996, p. 4 — powerhead weight and printed sound levels.

No additional parts-table entry added.

Service note · 019 T

019 T: oil-pump service tool and five included components

1132 890 1700 removes/installs the oil pump; five separately numbered components, not five saw parts.

  • Section 4.1 lists NEW parts required for model 019 T: service tool 1132 890 1700 for removing and installing the oil pump, INCLUDING the five following components. The parent tool has no item number; do not treat it as item 1 or claim a separate quantity beyond the printed list.
  • Drawing 170TI003 KN / tool inventory: 1 thrust piece 1132 893 8700; 2 threaded rod 1132 893 8200; 3 nut M5 9210 260 0700; 4 hex. head screw M6x60 9008 319 1450; 5 press arbor 1132 893 7200. These callouts identify SERVICE TOOL COMPONENTS, not replacement oil-pump or engine-housing parts.
  • The removal and installation drawings RENUMBER the same components: the inventory callouts must not be carried unchanged into either procedure. The TI points to the STIHL 019 T service manual for OTHER special servicing tools; this list is not a complete workshop-tool inventory.
  • Historical TI40/1996, exact 019 T only. Later 2012 IPL sheets are navigation anchors, not proof of original 1996 equipment. No extension to MS 190 T or MS 191 T, serial cutoff or verified physical interchange. No hardware operation was performed.

Source: TI 40/1996, p. 5 — oil-pump service tool and five included components.

Part numbers (6)
  • 1132 890 1700 — Oil-pump removal/installation service toolParent tool, includes five listed components · 019 T in TI40/1996 section 4
  • 1132 893 8700 — Thrust pieceInventory item 1 · 019 T in TI40/1996 section 4
  • 1132 893 8200 — Threaded rodInventory item 2 · 019 T in TI40/1996 section 4
  • 9210 260 0700 — Nut M5Inventory item 3 · 019 T in TI40/1996 section 4
  • 9008 319 1450 — Hex. head screw M6x60Inventory item 4 · 019 T in TI40/1996 section 4
  • 1132 893 7200 — Press arborInventory item 5 · 019 T in TI40/1996 section 4

Service note · 019 T

019 T: oil-pump removal and aligned press installation

Separate figure callouts; align pump groove with housing mark and stop when the press arbor meets the housing.

  • Section 5 requires all local regulations and the OWNER’S MANUAL safety precautions whenever the saw is started during repairs or maintenance. These historical service notes are not a complete start-up or safety procedure; no start-up was performed.
  • REMOVAL, section 5.1.1 / drawing 170TI002 KN: screw threaded rod (1) into oil pump (4); push thrust piece (2) over the threaded rod AS FAR AS IT WILL GO; screw M5 nut (3) onto the rod and tighten until the pump comes out of the engine housing. Here item 4 is the PUMP, not the inventory’s M6x60 screw.
  • INSTALLATION, section 5.1.2 / drawing 170TI004 KN: place the pump in position with its GROOVE lined up with the MARK ON THE ENGINE HOUSING; fit press arbor (1) on the pump; position thrust piece (2) in the housing bore FROM THE INSIDE; screw hex. head screw (3) into the thrust piece until the PRESS ARBOR BUTTS AGAINST THE HOUSING. Here item 1 is the arbor, not the removal rod; item 3 is the screw, not the removal nut.
  • No numerical press depth, force, screw torque, alternative drive method, lubrication instruction or oil-pump ordering number is supplied. The printed alignment and physical stopping condition must not be replaced by an invented dimension or tightening torque.
  • Historical TI40/1996, exact 019 T only. Later 2012 IPL sheets are navigation anchors, not proof of original 1996 equipment. No extension to MS 190 T or MS 191 T, serial cutoff or verified physical interchange. No hardware operation was performed.

Source: TI 40/1996, p. 5 · TI 40/1996, p. 6 — oil-pump removal and aligned press installation.

No additional parts-table entry added.

Service note · 019 T

019 T: engine and carburetor test data; torque-source gap

Engine pressure/vacuum each printed 0.6 bar (8.7 psi); carburetor pressure 0.4 bar (5.8 psi).

  • Section 5.2 ENGINE: pressure test 0.6 bar (8.7 psi); VACUUM test 0.6 bar (8.7 psi). The scan prints the same unsigned magnitude for both. Preserve the vacuum label; this is not a second positive-pressure test or an absolute-pressure specification.
  • Section 5.2 CARBURETOR: pressure test 0.4 bar (5.8 psi). Do not substitute the engine value. No test duration, acceptable leakage/drop, sealing fixture, crankshaft position, test sequence or instrument reference is printed on this page; these three values alone are not a complete test procedure.
  • Section 5.3 gives NO TIGHTENING TORQUES and refers to the STIHL 019 T service manual. An exact applicable manual was not identified in the bounded local document/PDF metadata, exact 019 T product links or resource/owner filename inventory. This is a documented local source gap, not proof no manual exists. No MS190T/MS191T torque table or generic fastener torque is substituted.
  • Historical TI40/1996, exact 019 T only. Later 2012 IPL sheets are navigation anchors, not proof of original 1996 equipment. No extension to MS 190 T or MS 191 T, serial cutoff or verified physical interchange. No hardware operation was performed.

Source: TI 40/1996, p. 6 — engine and carburetor test data; torque-source gap.

No additional parts-table entry added.

Service note · 019 T

019 T: complete twenty-code historical repair timetable

019 T repair-time allowances include diagnostic time; 0.1 hour = 6 minutes, trained workshop personnel.

  • Section 5.4 assumes TRAINED PERSONNEL in a PROPERLY EQUIPPED SERVICE WORKSHOP. Printed wording says “tenths of an hour minutes (0.1 = 6 minutes)”; the redundant “minutes” is retained as a source wording defect, not interpreted as decimal minutes. All values below are decimal HOURS. They are historical allowances, not a guarantee of elapsed repair time or a current price.
  • Code 1: Crankcase — 1.8 h.
  • Code 2: Crankshaft and/or Bearings — 2.2 h.
  • Code 3: Crankcase Sealing — 1.8 h.
  • Code 4: Crankshaft Seals — 1.2 h.
  • Code 5: Cylinder and/or piston — 1.6 h.
  • Code 6: Ignition — 0.7 h.
  • Code 7: Fuel Hose, Tank Vent — 0.5 h.
  • Code 8: Carb Flange or Connector — 1.0 h.
  • Code 9: Carburetor — 0.8 h.
  • Code 10: Oil pump system — 0.6 h.
  • Code 11: Handle Bar, Buffers, Handle Frame — 0.6 h.
  • Code 12: Recoil Starter — 0.5 h.
  • Code 13: Clutch — 0.5 h.
  • Code 14: Chain Brake — 0.5 h.
  • Code 15: Muffler — 1.0 h.
  • Code 16: Air Filter/Filter Cover — 0.3 h.
  • Code 17: Stop Switch — 0.5 h.
  • Code 18: Fuel Tank — 0.6 h.
  • Code 19: Engine Housing — 1.8 h.
  • Code 20: Misc. Repairs — 0.5 h.
  • ALL REPAIRS INCLUDE DIAGNOSTIC TIME. Do not add a second diagnostic allowance by default. The table is offered to supplement the STIHL repair-times table by cutting along the printed line/pasting it in or transferring the data by hand. No edition or literature ordering number for that parent table is supplied.
  • Crankcase (code 1), Crankcase Sealing (code 3) and Engine Housing (code 19) remain distinct printed rows despite their equal 1.8 h values. No additive combined-job rule or blank/zero cell is invented. Later repair timetables are separate dated evidence, not replacements for these 1996 values.
  • Historical TI40/1996, exact 019 T only. Later 2012 IPL sheets are navigation anchors, not proof of original 1996 equipment. No extension to MS 190 T or MS 191 T, serial cutoff or verified physical interchange. No hardware operation was performed.

Source: TI 40/1996, p. 7 — complete twenty-code historical repair timetable.

No additional parts-table entry added.

Conditional replacement · 019 T

019 T: fuel tank hose with integral grommet

Unchanged tank number hides a revised hose; change coincides with the carburetor.

  • Figure170TI011 KN depicts new hose1132 358 7700 with INTEGRALLY MOLDED GROMMET; old hose4205 141 8601 and separate grommet0000 989 0516 are deleted from this model configuration. The bend is pictured, but no dimensions or trimming specification is supplied.
  • Tank1132 350 0400 retains its number on both sides and includes items2–4; valve0747 313 6810 also remains unchanged. The table’s new grommet cell is blank because the new hose incorporates it, not because the seal may be omitted.
  • Introduction IN PROGRESS and explicitly coincident with the new carburetor (section7). Remark1: only modified tank version available from factory. Remark2: old hose AND old grommet remain available FOR OTHER MODELS. Do not read the prose “deleted” as universal discontinuation.
  • Later exact019 T B/doc86 lists both new hose and old separate hose/grommet. Preserve this edition/context distinction: that catalog coexistence does not erase the TI’s other-model qualification or establish mixed old/new fuel components as interchangeable.
  • Historical TI43/1999 english/USA evidence for 019 T, series1132 only. No extension to 019, 020 T, MS190 T or MS191 T from shared parts/series. Factory-availability remarks describe the historical issue, not current stock. No universal retrofit, numerical service setting or physical interchange verification is inferred.

Source: TI 43/1999, p. 4 · TI 43/1999, p. 5 — fuel tank hose with integral grommet.

Part numbers (5)
  • 1132 350 0400 — Fuel tankItem1 previous and new; includes2–4; modified version only · 019 T; TI43 section tank-hose
  • 0747 313 6810 — ValveItem2 unchanged · 019 T; TI43 section tank-hose
  • 0000 989 0516 — Separate grommetPrevious item3; remains for other models · 019 T; TI43 section tank-hose
  • 4205 141 8601 — HosePrevious item4; remains for other models · 019 T; TI43 section tank-hose
  • 1132 358 7700 — Hose with integrally molded grommetNew item4 · 019 T; TI43 section tank-hose

Wrong number or missing part for the 019 T? Report a correction →