← MS 341 · MS 361

Stihl 1135 · Section A · 1 of 15 · 34 parts

Crankcase

Fits MS 361, MS 361 C.

Parts diagrams →

Historical fitment & changes (1) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
1101112131415161618181919220202121222223232425262728293303132323334456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (34)

PosPart numberDescriptionQty
1 1135 020 2601 Crankcase 1
2 9503 003 0354 Grooved ball bearing 6202 1
3 9640 003 1560 Oil seal 15x22x4 1
4 0000 988 5211 Connector 1
5 0000 988 8600 Sleeve 2
6 1133 791 5900 Stop buffer 1
7 1135 020 2913 Crankcase 1
8 1135 020 2909 Crankcase 1
9 1135 020 2917 Crankcase 1
10 1135 020 2914 Crankcase 1
11 1135 020 2907 Crankcase 1
12 1135 020 2908 Crankcase 1
13 9523 003 4266 Grooved ball bearing 15x35x13 → replaced by 9523 003 4278 TI 15/2007 1
14 9640 003 1600 Oil seal 15x29.6x4 1
15 1124 791 2800 Stop buffer 1
16 1128 640 9100 Valve 1
18 0000 974 1200 Notched pin 2.6x8 1
19 1120 162 5200 Pin 1
20 1121 162 5205 Pin 1
21 1121 162 5200 Pin 1
22 1121 162 5200 Pin 1
23 1125 162 5209 Pin 1
24 0000 664 2405 Collar screw M8 1
25 1138 664 2400 Collar screw 2
26 0000 953 6605 Collar screw M8 2
27 1122 647 9400 Hose 1
28 1117 640 3800 Pickup body 1
29 1135 029 0500 Gasket 1
30 1135 030 0400 Crankshaft 1
31 9455 621 1520 Circlip 15x1 1
32 9022 341 1050 Spline screw IS-M5x25 5
33 0000 350 0525 Filler cap 1
34 9645 948 7734 O-ring 25x3.5 1
Not numbered on the diagram — assemblies, kits and options
— 1135 007 1050 Set of gaskets 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · MS 361 / MS 362 / MS 440 / MS 441 / MS 460 / MS 650 / MS 660 / MS 880

MS 361, MS 362, MS 440, MS 441, MS 460, MS 650, MS 660, MS 880: magnesium stud adhesive changes to Loctite 270

Metric-thread crankcase studs: Loctite 243 (USA 242) → Loctite 270; not polymer housings.

  • Exact listed magnesium-crankcase models: MS 361, MS 362, MS 440, MS 441, MS 460, MS 650, MS 660, MS 880. Their metric-thread studs change from Loctite 243 (USA: Loctite 242) to Loctite 270. No stud part number, serial changeover, cure time or torque is specified here.
  • Before stud reassembly, clean BOTH threads: insert the tap into the internal thread BY HAND, then blow out the threaded hole; brush off the external stud thread. Coat the cleaned stud with Loctite 270. This thread-cleaning instruction is not permission to enlarge the polymer repair-stud hole.
  • Loctite is NOT used for studs in polymer engine housings. The magnesium adhesive change does not override the separate polymer repair restrictions or give these models permission to use the oversized polymer repair studs.
  • The repeated words engine housings at the end of page3 are present in the original scan; they add no second instruction and are not silently corrected in the retained source.
  • Historical English TI29/2011. Only the printed model and material scope is admitted; no unlisted variants or predecessor models are inferred. No physical interchange test was performed.

Source: TI 29/2011, p. 3 — MS 361, MS 362, MS 440, MS 441, MS 460, MS 650, MS 660, MS 880: magnesium stud adhesive changes to Loctite 270.

No additional parts-table entry added.

Wrong number or missing part for the MS 361, MS 361 C? Report a correction →