Stihl 1135 · Section L · 11 of 15 · 46 parts
Carburetor HD-34B, HD-46
Fits MS 361, MS 361 C.
Historical fitment & changes (2) — includes parts and conditions not shown on this drawing.
Parts (46)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4116 121 5100 | Inlet needle | 1 |
| 2 | 4116 121 5000 | Inlet control lever | 1 |
| 3 | 1128 122 3002 | Spring | 1 |
| 4 | 1113 121 9200 | Spindle | 1 |
| 5 | 1114 122 7400 | Round head screw | 1 |
| 6 | 1135 121 5401 | Valve jet | 1 |
| 7 | 4117 122 9402 | Plug | 1 |
| 8 | 1128 129 0906 | Gasket | 1 |
| 9 | 4116 121 4700 | Metering diaphragm | 1 |
| 10 | 1135 121 0801 | End cover | 1 |
| 11 | 1121 122 7101 | Screw | 4 |
| 12 | 4116 121 4800 | Pump diaphragm | 1 |
| 13 | 4116 129 0902 | Gasket | 1 |
| 14 | 1133 121 0802 | End cover | 1 |
| 15 | 1114 122 7100 | Screw | 1 |
| 16 | 1127 122 3205 | Torsion spring | 1 |
| 17 | 1133 120 7101 | Throttle shaft with lever | 1 |
| 18 | 1117 122 9000 | E-clip | 1 |
| 19 | 1135 121 3302 | Throttle shutter | 1 |
| 20 | 1133 122 3200 | Torsion spring | 1 |
| 21 | 1135 120 7201 | Choke shaft with lever | 1 |
| 22 | 1123 122 9000 | E-clip | 1 |
| 23 | 4116 121 2900 | Choke shutter | 1 |
| 24 | 1127 122 6200 | Idle speed adjustment screw | 1 |
| 25 | 1122 121 7700 | Clamp | 1 |
| 26 | 1114 121 7800 | Strainer | 1 |
| 27 | not sold separately | Spring not available as a separate item | 1 |
| 28 | not sold separately | Pump piston not available as a separate item | 1 |
| 29 | not sold separately | Ball not available as a separate item | 1 |
| 30 | not sold separately | Plug not available as a separate item | 1 |
| 31 | 1115 122 7400 | Round head screw | 1 |
| 32 | 1110 122 7400 | Round head screw | 1 |
| 33 | 1128 122 6703 | High speed adjustment screw | 1 |
| 34 | 1135 122 6800 | Low speed adjustment screw | 1 |
| 35 | 4203 121 2700 | Cap Fitment / change note → | 2 |
| 36 | 1121 121 5602 | Fixed jet 0.52 | 1 |
| 37 | 4224 122 7801 | Oval head screw | 1 |
| 38 | 1121 122 7102 | Round head screw | 1 |
| 39 | 1135 122 6701 | High speed adjustment screw | 1 |
| 40 | 1135 122 6801 | Low speed adjustment screw | 1 |
| 41 | 1123 121 5601 | Fixed jet 0.61 | 1 |
| 42 | 9645 945 7527 | O-ring 12x2.5 | 1 |
| 43 | 5910 890 4500 | Puller Fitment / change note → option | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 1135 120 0601 | Carburetor HD-34B | 1 |
| — | 1135 120 0604 | Carburetor HD-46 | 1 |
| — | 1128 007 1066 | Set of carburetor parts | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Conditional replacement · MS 361
MS 361: revised limiter cap keeps the same number
Limiter cap 4203 121 2700 and the carburetor retain their part numbers despite revised cap/segment geometry; number alone does not identify the old or new cap.
Later reviewed guidance: MS 361: square-bit driver for fitted limiter caps
- Limiter cap 4203 121 2700 and the carburetor retain their part numbers despite revised cap/segment geometry; number alone does not identify the old or new cap.
- The new cap has no upper detent, adds an alignment mark and moves the lug from perpendicular to the screw slot into line with it.
- These models are explicitly named in the marked-segment subset. The L cap must not simply be pulled off at its stop: use the source’s quarter-turn offset and slot, groove, visible-lug and mark alignment.
- The segment drawing gives previous groove width 1.19 mm and revised width 1.50 mm; these identify the illustrated revision, not a machining instruction or universal service tolerance.
- H and L removal have separate alignment instructions. Puller 5910 890 4500 has a left-hand engagement thread; this note is not a complete carburetor removal or calibration procedure.
- Removed limiter caps must not be reused because removal damages them. Replace caps after screw replacement or carburetor cleaning; no permanent cap-removal modification is implied.
- Applies only to the named models with limiter cap 4203 121 2700. A shared catalog sheet is not approval for its other models or C/L variants. The sheet may contain uncapped versions; verify the actual carburetor configuration.
- Retained edition: English USA. Introduction is continuous, with no numeric serial cutoff. Historical availability is not current stock or universal regional applicability.
Source: TI 21/2005, p. 1 · TI 21/2005, p. 2 · TI 21/2005, p. 3 · TI 21/2005, p. 4 — Sections 1–5: named-model cap revision; cover list distinguished from marked-segment subset.
Part numbers (2)
- 4203 121 2700 — Limiter capUnchanged number, revised geometry · Named models using 4203 121 2700; single-use after removal
- 5910 890 4500 — Limiter-cap pullerService tool · Left-hand engagement; separate H/L alignment
Conditional replacement · MS 361
MS 361: square-bit driver for fitted limiter caps
Screwdriver 5910 890 2304 is specified for carburetors using limiter cap 4203 121 2700; its square bit reaches the adjusting screw through the fitted cap.
- Screwdriver 5910 890 2304 is specified for carburetors using limiter cap 4203 121 2700; its square bit reaches the adjusting screw through the fitted cap.
- Conditional on limiter cap 4203 121 2700 actually being fitted, not every carburetor or every model/variant on the shared catalog sheet. Model association comes from TI 21/2005 and the catalog cap row; TI 50/2006 specifies the tool by cap configuration.
- The without-cap basic-setting illustration starts with adjusting screws closed to their seats. It does not supply a turn count or extend the illustrated H/L arrangement to every carburetor on this sheet.
- The source distinguishes initial engagement at the first detent from final fully-home seating after the series-specific basic setting. Do not treat the first detent as the completed installation.
- Required idle/high-speed settings depend on the exact series; this bulletin supplies no universal screw-turn or RPM setting. Later series-specific service guidance still governs.
- Caps removed to service an adjusting screw or clean the carburetor must not be reused. TI 21/2005 supplies the removal dependency; this is not authorization for permanent limiter removal.
- Retained edition: English USA. Introduction is continuous, with no numeric serial cutoff. Historical availability is not current stock or universal regional applicability.
Source: TI 50/2006, p. 3 · TI 50/2006, p. 4 · TI 50/2006, p. 5 — Sections 3–3.4 and summary: capped-carburetor service tool and seating stages.
Part numbers (2)
- 5910 890 2304 — Square-bit carburetor screwdriverService tool · Carburetors using 4203 121 2700 fitted caps
- 4203 121 2700 — Limiter capExact tool configuration · New caps; final seating after series-specific basic setting
Wrong number or missing part for the MS 361, MS 361 C? Report a correction →