Stihl 1139 · Section B · 2 of 14 · 28 parts
Engine housing ErgoStart/Easy2Start
Fits MS 211, MS 211 C.
Historical fitment & changes (1) — includes parts and conditions not shown on this drawing.
Parts (28)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 1139 020 3004 | Engine housing | 1 |
| 2 | 0000 989 0608 | Grommet | 1 |
| 3 | 1120 162 5200 | Pin | 1 |
| 4 | 1123 162 5200 | Pin | 1 |
| 5 | 1123 162 5205 | Pin | 1 |
| 6 | 1123 640 3200 NLA | Oil pump 0.55 | 1 |
| 7 | 1139 647 4000 | Oil hose | 1 |
| 8 | 1123 640 3800 | Pickup body | 1 |
| 9 | 1128 640 9100 | Valve | 1 |
| 10 | 1139 358 7700 | Hose | 1 |
| 11 | 1139 122 3900 | Elbow connector | 1 |
| 12 | 1139 358 7706 | Hose | 1 |
| 13 | 1123 664 2400 | Collar screw Fitment / change note → | 1 |
| 14 | 1123 664 2402 NLA | Collar screw | 1 |
| 15 | 1139 442 1600 | Contact spring | 1 |
| 16 | 1139 353 2701 | Connector | 1 |
| 17 | 4130 350 6200 | Fuel pump → replaced by 4128 120 0100 TI 6/2009 | 1 |
| 18 | not sold separately | Hose 2.2x5.4x38 mm, R1 not available as a separate item | 1 |
| 19 | not sold separately | Hose 2.2x5.4x98 mm, R1 not available as a separate item | 1 |
| 20 | not sold separately | Hose 3.1x5.7x67 mm, R3 not available as a separate item | 1 |
| 21 | 0000 350 5802 | Tank vent | 1 |
| 22 | 0000 350 3500 | Pickup body | 1 |
| 23 | 0000 350 0525 | Filler cap | 1 |
| 24 | 9645 948 7734 | O-ring 25x3.5 | 1 |
| 25 | 0000 350 0526 | Filler cap | 1 |
| 26 | 9645 948 2470 | O-ring 23x3 | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 0000 930 2802 | Hose 2.2x5.4 mm x 1 m, R1 not illustratedoption | 1 |
| — | 0000 930 2803 | Hose 3.1x5.7 mm x 1 m, R3 not illustratedoption | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · MS 171 / MS 181 / MS 211
MS 171, MS 181, MS 211: oversized repair stud at 16 Nm
1123 664 2400 (8 mm) → 1123 664 2405 (9 mm); damaged polymer-housing threads only.
- Exact table scope: MS 171, MS 181, MS 211. Standard stud 1123 664 2400 has diameter 8 mm; repair stud 1123 664 2405 has diameter 9 mm (1 mm larger). Required repair-stud tightening torque: 16 Nm. This is a conditional repair, not a routine replacement or a standard-stud torque specification.
- Use only when the housing thread is damaged or stripped and the standard collar screw cannot reach its specified tightening torque. If the housing is cracked or completely destroyed around the threads, the repair stud CANNOT be used; replace the entire engine housing.
- DO NOT drill out the mounting hole. Position the repair stud by hand so it engages the EXISTING thread; use the stud driver to insert it PERPENDICULAR to the supporting surface, tighten to the listed repair torque, then unscrew the driver. Select the driver by the actual shaft geometry described in section1; no model-specific driver is inferred from the repair table.
- Loctite is NOT recommended for repair studs in polymer engine housings (section2); section3 also says Loctite is not used for studs in polymer housings. Do not transfer the magnesium-crankcase Loctite 270 rule to this repair.
- No repair solution is offered for UNLISTED chain saws in this bulletin. No serial threshold, permission for unlisted model suffixes, or applicability beyond the named models is supplied.
- Historical English TI29/2011. Only the printed model and material scope is admitted; no unlisted variants or predecessor models are inferred. No physical interchange test was performed.
Source: TI 29/2011, p. 2 · TI 29/2011, p. 3 — MS 171, MS 181, MS 211: oversized repair stud at 16 Nm.
Part numbers (2)
- 1123 664 2400 — Standard stud, diameter 8 mmstandard-stud · MS 171, MS 181, MS 211: oversized repair stud at 16 Nm
- 1123 664 2405 — Oversized repair stud, diameter 9 mmconditional-repair · MS 171, MS 181, MS 211: oversized repair stud at 16 Nm
Wrong number or missing part for the MS 211, MS 211 C? Report a correction →