Stihl 1140 · Assembly · 7 of 13 · 26 parts
Engine housing, Chain tensioner
Fits MS 391.
Historical fitment & changes (1) — includes parts and conditions not shown on this drawing.
Parts (26)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 1140 020 3004 | Engine housing | 1 |
| 2 | 1140 020 3051 | Engine housing | 1 |
| 3 | 1128 640 9100 | Valve | 1 |
| 4 | 0000 974 1200 | Notched pin 2.6x8 | 1 |
| 5 | 1123 162 5200 | Pin | 1 |
| 6 | 1123 162 5205 | Pin | 1 |
| 7 | 1121 162 5200 | Pin | 1 |
| 8 | 1120 162 5200 | Pin | 1 |
| 9 | 9645 945 7444 | O-ring 4x1.5 | 1 |
| 10 | 1117 640 3800 | Pickup body | 1 |
| 11 | 1140 647 9401 | Hose | 1 |
| 12 | 0000 664 2407 | Collar screw M8 | 1 |
| 13 | 0000 664 2404 | Collar screw M8 | 1 |
| 14 | 0000 664 2411 | Collar screw D9/M8 option | 1 |
| 15 | 0000 350 0533 | Filler cap | 1 |
| 16 | 9645 948 7734 | O-ring 25x3.5 | 1 |
| 17 | 1133 791 5900 | Stop buffer | 1 |
| 18 | 1140 140 7801 | Pre-separator | 1 |
| 19 | 9074 477 2995 | Pan head self-tapping screw IS-P4x12 Binding thread | 1 |
| 20 | 1127 007 1003 | Spur gear / chain adjusting screw kit | 1 |
| 21 | 1127 640 1900 | Tensioner slide | 1 |
| 22 | 1123 664 1400 | Thrust pad | 1 |
| 23 | 1127 664 2200 | Cover | 1 |
| 24 | 9074 478 3005 | Pan head self-tapping screw IS-P4x14 | 1 |
| 25 | 1140 080 1805 | Fan housing | 1 |
| 26 | 0000 790 6102 | Screw assy. M5 | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · MS 311 / MS 391
MS 311, MS 391: oversized repair stud at 16 Nm
1123 664 2400 (8 mm) → 1123 664 2405 (9 mm); damaged polymer-housing threads only.
- Exact table scope: MS 311, MS 391. Standard stud 1123 664 2400 has diameter 8 mm; repair stud 1123 664 2405 has diameter 9 mm (1 mm larger). Required repair-stud tightening torque: 16 Nm. This is a conditional repair, not a routine replacement or a standard-stud torque specification.
- Use only when the housing thread is damaged or stripped and the standard collar screw cannot reach its specified tightening torque. If the housing is cracked or completely destroyed around the threads, the repair stud CANNOT be used; replace the entire engine housing.
- DO NOT drill out the mounting hole. Position the repair stud by hand so it engages the EXISTING thread; use the stud driver to insert it PERPENDICULAR to the supporting surface, tighten to the listed repair torque, then unscrew the driver. Select the driver by the actual shaft geometry described in section1; no model-specific driver is inferred from the repair table.
- Loctite is NOT recommended for repair studs in polymer engine housings (section2); section3 also says Loctite is not used for studs in polymer housings. Do not transfer the magnesium-crankcase Loctite 270 rule to this repair.
- No repair solution is offered for UNLISTED chain saws in this bulletin. No serial threshold, permission for unlisted model suffixes, or applicability beyond the named models is supplied.
- Historical English TI29/2011. Only the printed model and material scope is admitted; no unlisted variants or predecessor models are inferred. No physical interchange test was performed.
Source: TI 29/2011, p. 2 · TI 29/2011, p. 3 — MS 311, MS 391: oversized repair stud at 16 Nm.
Part numbers (2)
- 1123 664 2400 — Standard stud, diameter 8 mmstandard-stud · MS 311, MS 391: oversized repair stud at 16 Nm
- 1123 664 2405 — Oversized repair stud, diameter 9 mmconditional-repair · MS 311, MS 391: oversized repair stud at 16 Nm
Wrong number or missing part for the MS 391? Report a correction →