← E20 / E220Q · MSE 220 / MSE 220 C

Stihl 1207 · Section A · 1 of 5 · 44 parts

Electric motor E 220, E 20

Fits E 20, E 220.

Parts diagrams →

Historical fitment & changes (4) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
1101112131415161718192202122232425262727282829330313244056789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (44)

PosPart numberDescriptionQty
1 1207 600 0803 Motor housing 1
2 1207 435 7800 Safety switch 1
3 0000 997 0429 Compression spring 1
4 1207 435 2000 Pin 1
5 1207 431 1800 Plug 1
6 1207 430 1800 Indicator lamp 230 V 1
7 0000 988 6115 Plug 1
8 1207 600 0100 Stator 230 V 1
8 1207 600 0102 Stator 120 V 1
9 9074 478 4355 Pan head self-tapping screw IS-P5x80 2
10 1206 084 1800 Air guide ring 1
11 1207 600 1000 Rotor with fanwheel 230 V Fitment / change note → 1
11 1207 600 1002 Rotor with fanwheel 120 V 1
12 1206 608 1200 Washer 1
13 9503 003 9670 Grooved ball bearing 608-2Z 1
14 1206 086 0502 Fanwheel 1
15 1207 435 1200 Overload cutout 230/240 V 1
15 1207 430 1500 Overload cutout 120 V 1
16 1206 435 8000 Sealing washer 1
17 1206 435 0310 Quick-action switch 1
18 4804 605 1000 Capacitor 1
18 1208 605 1000 Capacitor 120 V 1
19 1207 440 2003 Connecting cable 120 V 1
19 1207 440 2001 Connecting cable 230 V 1
20 1204 431 2400 Cable protector 1
21 1207 435 0301 Switch 1
21 1207 435 0300 Switch 1
22 1207 430 1600 Starting corrent limiter 1
23 1204 431 2500 Cable clamp 1
24 9074 478 3025 Pan head self-tapping screw IS-P4x16 2
25 1207 791 0601 Handle molding 1
26 9074 478 3075 Pan head self-tapping screw IS-P4x19 8
27 1207 600 2602 Brush holder 2
28 1207 007 1005 Set of carbon brushes 1
29 1206 791 1506 Front handle 1
30 9074 478 3475 Pan head self-tapping screw IS-P4.5x25 3
31 0000 967 3736 Warning pictogram MSE 1
31 1206 967 3505 Warning pictogram MSE 1
32 1207 967 1807 Rating plate E 220 1
32 1207 967 1805 Rating plate E 220 Fitment / change note → 1
40 1207 967 1800 Rating plate E 20 1
40 1207 967 1801 Rating plate E 20 1
40 1207 967 1802 Rating plate E 20 Fitment / change note → 1
Not numbered on the diagram — assemblies, kits and options
— 1207 029 8800 Insert not illustrated 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Historical fitment · E 20 / E 20 C

E 20 / E 20 C: distinct clip-in nameplates replace riveted versions

The E20 and E20C have different nameplate pairs. The two rivets are deleted from the new clip-in arrangement; the clutch serial does not date this change.

  • E20: aluminium nameplate 1207 967 1500 → plastic clip-in 1207 967 1501. E20C: 1207 967 1505 → 1207 967 1502. Do not merge the model-specific rows.
  • Two round-head rivets 0000 974 1000 are deleted from the new arrangement. Original plates and rivets remain available for older machines in this bulletin; this is not a blanket rivet discontinuation.
  • The logo is embedded in the carrier by a two-component process. Better scratch resistance and longer legibility are source claims, not tested here.
  • Nameplate introduction is in progress, with no numeric cutoff. The X31 010 462 serial belongs only to friction-clutch summary3.1, not nameplate summary3.2.
  • The catalog motor sheets are linked as contextual assembly pages: their titles distinguish E20 and E20C although their used_by label groups E20/E220. The source itself explicitly names E20C; no E220 coverage or unlisted retrofit fastening detail is inferred.
  • TI35/1992 is listed only as the previous E20 bulletin. Its unavailable contents are not required to read these complete current rows and are not imported as compatibility evidence.
  • TI40/1994 is dated November18,1994. Historical availability is not current stock; this review does not verify a physical retrofit. Shared E20/E220 catalog sheets do not extend this bulletin to E220, MSE220 or other successor models.

Source: TI 40/1994, p. 2 · TI 40/1994, p. 3 — Section2 and summary3.2, distinct model rows and availability.

Part numbers (5)
  • 1207 967 1500 — Original aluminium E20 nameplateOld · E20 only
  • 1207 967 1501 — Clip-in plastic E20 nameplateNew · E20 only
  • 1207 967 1505 — Original aluminium E20C nameplateOld · E20C only
  • 1207 967 1502 — Clip-in plastic E20C nameplateNew · E20C only
  • 0000 974 1000 — Round-head rivet, twoDeleted from new arrangement · Retained for older nameplates

Service note · E 220

E 220: original 120 V / 60 Hz specifications

Original electrical, speed and size figures retain their test conditions; these are not universal E 220 ratings.

  • Page1 introduces E 220 as a DEVELOPMENT OF E 20, using the new three-digit electric-saw nomenclature and described as top of the line. The photograph shows a complete E 220 with cutting attachment; it supplies no measured bar length, chain specification or additional variant claim.
  • Section1.1 specifies 1.7 kW, 120 V, 60 Hz, insulation class II and enclosure IP 20. Current drawn OFF-LOAD WITHOUT CUTTING ATTACHMENT is 8.8 A; nominal current consumption is 15.0 A; fuse is printed 15/16 A. These are source specifications, not live measurements, a field-test instruction or a choice of circuit protection for an unidentified installation.
  • Section1.2 specifies CHAIN-SPROCKET speeds WITH BAR AND CHAIN: 5600 RPM WITH LOAD and 7000 RPM WITHOUT LOAD. Do not conflate this no-load speed condition with the 8.8 A measurement WITHOUT the cutting attachment, or treat sprocket RPM as motor RPM or chain linear speed.
  • Section1.3 specifies oil tank capacity 0.42 US pt, weight 11 lbs WITHOUT BAR, CHAIN AND CONNECTING CORD, and connecting-cord length 1.15 ft. Preserve the original units and exclusions; no fabricated conversion precision or full operating weight.
  • Section1.4 says cutting attachment AS E 20, SEE CHAIN / BAR CATALOG. This retains the stated relationship, not an assertion of any particular bar/chain combination: no pitch, gauge, drive-link count or bar order number is printed. Actual combination selection remains subject to that catalog; the cover photograph does not supply missing dimensions.
  • The exact E 20/E 220 motor IPL includes both 120 V and 230 V components. These 120 V / 60 Hz figures are NOT generalized to all E 220 markets. The TI rotor number versus IPL voltage discrepancy is preserved in the separate rotor note; specifications alone cannot resolve it.
  • Historical TI13/1998, series 1207. Only the named E 220 and, where expressly stated, E 20 are covered; no extension to C variants or MSE successors from a shared sheet/part number. Supply and documentation statements are historical, not current stock or publication promises. No hardware operation was performed.

Source: TI 13/1998, p. 1 · TI 13/1998, p. 2 — Page1 full introduction/photograph; page2 sections1.1–1.4 including all units, qualifiers and Chain/Bar catalog reference.

No additional parts-table entry added.

Conditional replacement · E 220 / E 20

E 220 / E 20: index-C rotor rule has a voltage conflict

E 220 requires index C; the TI’s rotor number conflicts with the retained IPL voltage labeling.

  • Section2 identifies MODIFIED ROTOR 1207 600 1000 by index letter C STAMPED BEHIND 1207 600 1100. The latter number identifies the rotor WITHOUT FANWHEEL and is explicitly NOT A SPARE PART NUMBER. It is retained here as an identification marking, not an orderable replacement or a second rotor assembly.
  • USE ONLY INDEX C ROTORS IN E 220. Index C rotors MAY ALSO be installed in E 20 AFTER existing stocks of rotors UP TO INDEX B have been used up. The E 20 stock-exhaustion rule does not permit index A/B in E 220 and supplies no serial cutoff, reverse interchange permission or blanket replacement requirement for every installed E 20 rotor.
  • Section3.1 and its asterisk say rotor 1207 600 1000 continues under the ORIGINAL PART NUMBER but with the LATEST E 220 SPECIFICATION, INDEX C. Same order number therefore does not distinguish an older physical rotor from the required version; inspect the stated index marking. Index C on a rotor is NOT the C suffix of a saw model.
  • UNRESOLVED VOLTAGE CONFLICT: this TI’s section1 specifies 120 V / 60 Hz but sections2 and3.1 print rotor 1207 600 1000. The retained E 20/E 220 motor IPL labels 1207 600 1000 as ROTOR WITH FANWHEEL 230 V, and 1207 600 1002 as ROTOR WITH FANWHEEL 120 V. Both source statements are preserved. Do not silently correct the TI to 1002, relabel 1000 as 120 V, or use this note as voltage-matched ordering approval. An exact-market/version source or inspected component is needed to resolve the conflict.
  • The service warning requires ALL NATIONAL AND LOCAL SAFETY REGULATIONS and the OWNER’S MANUAL safety precautions if the unit is started during repairs or maintenance. This bulletin gives no energized-test procedure. No startup, wiring, rotor-fit or electrical performance verification is claimed.
  • Historical TI13/1998, series 1207. Only the named E 220 and, where expressly stated, E 20 are covered; no extension to C variants or MSE successors from a shared sheet/part number. Supply and documentation statements are historical, not current stock or publication promises. No hardware operation was performed.

Source: TI 13/1998, p. 2 — Page2 complete section2 and section3.1 rotor row/asterisk; section1.1 voltage context compared with exact motor IPL.

Part numbers (1)
  • 1207 600 1000 — Modified rotor; index CTI order number; unresolved IPL voltage conflict · E 220 index C only; E 20 stock-exhaustion condition

Historical fitment · E 220 / E 20

E 220 / E 20: model plates and historical IPL transition

New E 220 plates and discontinued E 20 plates are distinct model identities, not a relabeling instruction.

  • Section3.1 lists NAMEPLATE E 220 1207 967 1507 and RATING PLATE E 220 USA 1207 967 1805 as new spares. Section3.2 DISCONTINUES NAMEPLATE E 20 1207 967 1501 and RATING PLATE E 20 USA 1207 967 1802. These are separate named-model plate lists, not explicit substitution permission or authorization to turn an E 20 into an E 220 by changing labels.
  • The exact shared chain-sprocket-cover IPL retains E 220 model plate 1207 967 1507; the motor IPL retains E 220 rating plate 1207 967 1805 AND E 20 rating plate 1207 967 1802. Retention of the old rating plate in a later catalog does not erase the TI’s historical discontinued-parts statement. The original E 20 nameplate 1207 967 1501 has no matching row on these sheets; no drawing position is invented. USA scope is retained even though the catalog rating-plate description is shorter.
  • Section4 says E 220 parts will be incorporated into the EXISTING E 20 ILLUSTRATED PARTS LIST; included in the NEXT MICROFICHE AND CD-ROM ISSUE (1.98). NO GENERAL REPRINT WITH E 220 is planned for the printed list; it will be issued at a LATER DATE. This is the source’s publication plan, not proof of an actual release date, a new print edition in hand or complete part interchangeability.
  • No serial introduction point, plate-installation procedure or voltage conversion is given. The rotor supply footnote is handled in the separate index-C note. Footer copyright1998, Andreas Stihl D1/MTK Technical Documentation6263 is bibliographic context.
  • Historical TI13/1998, series 1207. Only the named E 220 and, where expressly stated, E 20 are covered; no extension to C variants or MSE successors from a shared sheet/part number. Supply and documentation statements are historical, not current stock or publication promises. No hardware operation was performed.

Source: TI 13/1998, p. 2 — Page2 sections3.1–3.2 plate lists, complete section4 publication plan and footer.

Part numbers (4)
  • 1207 967 1507 — Nameplate E 220New E 220 spare · E 220 only
  • 1207 967 1805 — Rating plate E 220 USANew E 220 spare · E 220 USA only
  • 1207 967 1501 — Nameplate E 20Discontinued in TI; no matching retained row · E 20 only
  • 1207 967 1802 — Rating plate E 20 USADiscontinued in TI; still present in retained IPL · E 20 USA only

Wrong number or missing part for the E 20, E 220? Report a correction →