Stihl 1207 · Section D · 4 of 5 · 31 parts
Chain sprocket cover
Fits E 20, E 220.
Historical fitment & changes (2) — includes parts and conditions not shown on this drawing.
Parts (31)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 1207 642 7801 | Washer | 2 |
| 2 | 1207 640 7505 | Spur gear Fitment / change note → | 1 |
| 3 | 1207 640 0400 | Gear housing | 1 |
| 4 | 9513 003 3210 | Needle cage 12x16x10 | 1 |
| 5 | 1110 664 2400 | Collar screw | 1 |
| 6 | 1121 664 2400 | Collar screw | 1 |
| 7 | 1125 664 1400 | Thrust pad | 1 |
| 8 | 1125 640 1900 | Tensioner slide | 1 |
| 9 | not sold separately | Spur gear not available as a separate item | 1 |
| 10 | not sold separately | Adjusting screw not available as a separate item | 1 |
| 11 | 9646 945 0490 | O-ring 7x1.5 | 1 |
| 12 | 1122 664 2200 | Cover plate | 1 |
| 13 | 9041 216 0630 | Pan head screw M4x8 | 1 |
| 14 | 1121 648 6610 | Bumper strip | 4 |
| 15 | 1128 664 0500 | Bumper spike | 2 |
| 16 | 9074 478 4145 | Pan head self-tapping screw IS-P5x32 | 4 |
| 17 | 1207 642 7810 | Washer | 1 |
| 18 | 1207 640 2050 | Chain sprocket 3/8" 8T Fitment / change note → | 1 |
| 18 | 1207 640 2051 | Chain sprocket 0.325" 8T Fitment / change note → | 1 |
| 19 | 1207 162 4200 | Collar screw Fitment / change note → | 1 |
| 20 | 1207 162 8900 | Washer Fitment / change note → | 2 |
| 21 | 9485 648 2044 | Cup spring 34x12.2x1.5 Fitment / change note → | 3 |
| 22 | 1207 648 0405 | Chain sprocket cover Fitment / change note → | 1 |
| 23 | 0000 961 1404 | Ring | 1 |
| 24 | 1207 967 1507 | Model plate E 220 Fitment / change note → | 1 |
| 25 | 1207 967 1508 | Model plate E 220 C | 1 |
| 26 | 0000 955 0801 | Hexagon nut M8 | 1 |
| 27 | 9008 319 0960 | Hexagon head screw M5x12 | 2 |
| 28 | 9214 320 0700 | Lock nut M5 | 2 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 1125 007 1021 | Spur gear / chain adjusting screw kit | 1 |
| — | 1207 007 1002 | Set of washers / cup springs Fitment / change note → | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Conditional replacement · E 20
E 20: friction-clutch retrofit requires the revised cover and gearwheel
From X 31 010 462, the sprocket drive changes from two-flat keyed engagement to a friction clutch. The source permits an E20 retrofit only with the required companion parts.
X 31 010 462 — Friction-clutch production introduction for E20; not nameplate changeover or universal electric-saw fitment.
- The service note allows backfitting to any STIHL E20 electric saw, requiring replacement gearwheel and chain sprocket cover in addition to the illustrated clutch parts. This is the named historical E20 scope, not permission to fit the clutch to all electric saws.
- Original cover 1207 648 0400 must not be used with the new round-hole sprocket/friction clutch. New cover 1207 648 0405 may also be used on older machines without the clutch: compatibility is directional. Gearwheel 1207 640 7500 changes to 1207 640 7505.
- The new sprocket has a round mounting hole; the original has two flats. When replacing a sprocket on a friction-clutch machine, a NEW collar screw 1207 162 4200 must also be fitted. It has a LEFT-HAND thread into the gearwheel shaft. No tightening torque is given here.
- Cup springs must always be replaced as a set of THREE. Set 1207 007 1002 includes table items7 and8: two washers 1207 162 8900 and three cup springs 9485 648 2044. The drawing has one washer on each side of the sprocket, not four washers total.
- The original page1 exploded drawing shows collar screw, three oriented cup springs, upper washer, sprocket, lower washer and gearwheel. Use that original illustration and the assembly sequence inside the revised cover for spring orientation; this text is not a substitute orientation diagram.
- Complete 3/8-inch 8-tooth sprocket 1207 640 2050 and complete .325-inch 8-tooth sprocket 1207 640 2051 each include table items4 and5: sprocket plus collar screw. The spring/washer set is separately listed, not included by that statement. Do not infer chain/bar interchange between pitches.
- Old separate sprockets 1207 642 1310 (3/8-inch) and 1207 642 1311 (.325-inch) remain for older machines; new sprockets are not separate items. Original washer 0000 958 1218 and E-clip 9460 624 1001 remain for older machines, not listed in the new friction-clutch stack. Old cover and gearwheel are while-stocks-last.
- The source claims reduced ring-gear load, five-to-eight times gearwheel wear life, absorbed jolts and avoided motor lockup under the described loading. These are vendor claims, not measured performance or an assurance against all jamming.
- TI40/1994 is dated November18,1994. Historical availability is not current stock; this review does not verify a physical retrofit. Shared E20/E220 catalog sheets do not extend this bulletin to E220, MSE220 or other successor models.
Source: TI 40/1994, p. 1 · TI 40/1994, p. 2 · TI 40/1994, p. 3 — Sections1.1–1.2, full service note, exploded drawing and summary3.1.
Part numbers (14)
- 1207 648 0400 — Original sprocket coverProhibited with friction clutch · E20 friction-clutch configuration; restrictions above
- 1207 648 0405 — Revised sprocket coverRequired; also fits old configuration per source · E20 friction-clutch configuration; restrictions above
- 1207 640 7500 — Original gearwheelOld · E20 friction-clutch configuration; restrictions above
- 1207 640 7505 — Revised gearwheelRequired for retrofit · E20 friction-clutch configuration; restrictions above
- 1207 640 2050 — Complete sprocket 3/8 inch 8TSprocket plus new collar screw · E20 friction-clutch configuration; restrictions above
- 1207 640 2051 — Complete sprocket .325 inch 8TSprocket plus new collar screw · E20 friction-clutch configuration; restrictions above
- 1207 642 1310 — Old sprocket 3/8 inch 8TOlder keyed configuration · E20 friction-clutch configuration; restrictions above
- 1207 642 1311 — Old sprocket .325 inch 8TOlder keyed configuration · E20 friction-clutch configuration; restrictions above
- 1207 162 4200 — Left-hand-thread collar screwRenew with sprocket · E20 friction-clutch configuration; restrictions above
- 1207 007 1002 — Cup spring and washer setTwo washers and three springs · E20 friction-clutch configuration; restrictions above
- 1207 162 8900 — WasherTwo required · E20 friction-clutch configuration; restrictions above
- 9485 648 2044 — Cup springThree; replace as set · E20 friction-clutch configuration; restrictions above
- 0000 958 1218 — Original washerRetained for older machines · E20 friction-clutch configuration; restrictions above
- 9460 624 1001 — Original E-clipRetained for older machines · E20 friction-clutch configuration; restrictions above
Historical fitment · E 220 / E 20
E 220 / E 20: model plates and historical IPL transition
New E 220 plates and discontinued E 20 plates are distinct model identities, not a relabeling instruction.
- Section3.1 lists NAMEPLATE E 220 1207 967 1507 and RATING PLATE E 220 USA 1207 967 1805 as new spares. Section3.2 DISCONTINUES NAMEPLATE E 20 1207 967 1501 and RATING PLATE E 20 USA 1207 967 1802. These are separate named-model plate lists, not explicit substitution permission or authorization to turn an E 20 into an E 220 by changing labels.
- The exact shared chain-sprocket-cover IPL retains E 220 model plate 1207 967 1507; the motor IPL retains E 220 rating plate 1207 967 1805 AND E 20 rating plate 1207 967 1802. Retention of the old rating plate in a later catalog does not erase the TI’s historical discontinued-parts statement. The original E 20 nameplate 1207 967 1501 has no matching row on these sheets; no drawing position is invented. USA scope is retained even though the catalog rating-plate description is shorter.
- Section4 says E 220 parts will be incorporated into the EXISTING E 20 ILLUSTRATED PARTS LIST; included in the NEXT MICROFICHE AND CD-ROM ISSUE (1.98). NO GENERAL REPRINT WITH E 220 is planned for the printed list; it will be issued at a LATER DATE. This is the source’s publication plan, not proof of an actual release date, a new print edition in hand or complete part interchangeability.
- No serial introduction point, plate-installation procedure or voltage conversion is given. The rotor supply footnote is handled in the separate index-C note. Footer copyright1998, Andreas Stihl D1/MTK Technical Documentation6263 is bibliographic context.
- Historical TI13/1998, series 1207. Only the named E 220 and, where expressly stated, E 20 are covered; no extension to C variants or MSE successors from a shared sheet/part number. Supply and documentation statements are historical, not current stock or publication promises. No hardware operation was performed.
Source: TI 13/1998, p. 2 — Page2 sections3.1–3.2 plate lists, complete section4 publication plan and footer.
Part numbers (4)
- 1207 967 1507 — Nameplate E 220New E 220 spare · E 220 only
- 1207 967 1805 — Rating plate E 220 USANew E 220 spare · E 220 USA only
- 1207 967 1501 — Nameplate E 20Discontinued in TI; no matching retained row · E 20 only
- 1207 967 1802 — Rating plate E 20 USADiscontinued in TI; still present in retained IPL · E 20 USA only
Wrong number or missing part for the E 20, E 220? Report a correction →