Stihl 1207 · Section C · 3 of 5 · 40 parts
Oil pump, Chain brake
Fits E 20, E 220.
Historical fitment & changes (2) — includes parts and conditions not shown on this drawing.
Parts (40)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 1207 640 0500 | Gear housing | 1 |
| 2 | 9513 003 1920 | Needle cage 8x12x10 | 1 |
| 3 | 9503 003 9870 | Grooved ball bearing 609-2Z | 1 |
| 4 | 9456 621 2660 | Circlip 24x1.2 | 1 |
| 5 | 1207 431 6400 | Insulating foil | 1 |
| 6 | 1121 162 5205 | Pin | 1 |
| 7 | 1206 647 9401 | Delivery hose | 1 |
| 8 | 1207 647 9400 | Pickup hose | 1 |
| 9 | 1208 640 3000 | Pump housing | 1 |
| 10 | 1206 640 4700 | Pump piston | 1 |
| 11 | 9517 003 5060 | Cylindrical roller 4x10.8 | 1 |
| 14 | 1116 647 1806 | Spur gear | 1 |
| 15 | 0000 958 0504 | Washer | 1 |
| 16 | 9074 478 3075 | Pan head self-tapping screw IS-P4x19 | 2 |
| 17 | 1206 647 9100 | Grommet | 1 |
| 18 | 1121 162 5010 | Lever | 1 |
| 19 | 0000 997 0628 | Spring | 1 |
| 20 | 9460 624 0400 | E-clip 4 | 1 |
| 21 | 1206 162 3200 | Carrier | 1 |
| 22 | 1206 160 5000 | Lever | 1 |
| 23 | 1206 160 5400 | Brake band | 1 |
| 24 | 9079 319 1350 | Flat head screw M6x25 | 1 |
| 25 | 1206 162 7900 | Tension spring | 1 |
| 26 | 1206 160 2402 | Brake drum | 1 |
| 27 | 1207 642 0400 | Drive pinion | 1 |
| 28 | 1207 642 7800 | Washer | 1 |
| 29 | 1207 162 9300 | Screw M4x12 l/h thread | 1 |
| 30 | 1206 351 0400 | Oil tank | 1 |
| 31 | 1206 646 1200 | Strainer | 1 |
| 33 | 1117 350 0905 | Filler cap retainer | 1 |
| 34 | 9099 021 2360 | Self-tapping screw 3.5x9.5 | 1 |
| 35 | 1206 790 9100 | Hand guard | 1 |
| 36 | 9099 021 4980 | Self-tapping screw 6.3x32 | 1 |
| 37 | 9645 945 2820 | O-ring 25x2.5 | 1 |
| 38 | 1206 086 0502 | Fanwheel | 1 |
| 40 | 1118 640 3007 | Pump housing | 1 |
| 41 | 1206 647 3000 | Control pin | 1 |
| 42 | 0000 997 0211 | Compression spring | 1 |
| 43 | 9516 003 1220 | Ball Ø 3 mm | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 1208 640 3250 | Oil pump Fitment / change note → | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Conditional replacement · E 20
E 20: friction-clutch retrofit requires the revised cover and gearwheel
From X 31 010 462, the sprocket drive changes from two-flat keyed engagement to a friction clutch. The source permits an E20 retrofit only with the required companion parts.
X 31 010 462 — Friction-clutch production introduction for E20; not nameplate changeover or universal electric-saw fitment.
- The service note allows backfitting to any STIHL E20 electric saw, requiring replacement gearwheel and chain sprocket cover in addition to the illustrated clutch parts. This is the named historical E20 scope, not permission to fit the clutch to all electric saws.
- Original cover 1207 648 0400 must not be used with the new round-hole sprocket/friction clutch. New cover 1207 648 0405 may also be used on older machines without the clutch: compatibility is directional. Gearwheel 1207 640 7500 changes to 1207 640 7505.
- The new sprocket has a round mounting hole; the original has two flats. When replacing a sprocket on a friction-clutch machine, a NEW collar screw 1207 162 4200 must also be fitted. It has a LEFT-HAND thread into the gearwheel shaft. No tightening torque is given here.
- Cup springs must always be replaced as a set of THREE. Set 1207 007 1002 includes table items7 and8: two washers 1207 162 8900 and three cup springs 9485 648 2044. The drawing has one washer on each side of the sprocket, not four washers total.
- The original page1 exploded drawing shows collar screw, three oriented cup springs, upper washer, sprocket, lower washer and gearwheel. Use that original illustration and the assembly sequence inside the revised cover for spring orientation; this text is not a substitute orientation diagram.
- Complete 3/8-inch 8-tooth sprocket 1207 640 2050 and complete .325-inch 8-tooth sprocket 1207 640 2051 each include table items4 and5: sprocket plus collar screw. The spring/washer set is separately listed, not included by that statement. Do not infer chain/bar interchange between pitches.
- Old separate sprockets 1207 642 1310 (3/8-inch) and 1207 642 1311 (.325-inch) remain for older machines; new sprockets are not separate items. Original washer 0000 958 1218 and E-clip 9460 624 1001 remain for older machines, not listed in the new friction-clutch stack. Old cover and gearwheel are while-stocks-last.
- The source claims reduced ring-gear load, five-to-eight times gearwheel wear life, absorbed jolts and avoided motor lockup under the described loading. These are vendor claims, not measured performance or an assurance against all jamming.
- TI40/1994 is dated November18,1994. Historical availability is not current stock; this review does not verify a physical retrofit. Shared E20/E220 catalog sheets do not extend this bulletin to E220, MSE220 or other successor models.
Source: TI 40/1994, p. 1 · TI 40/1994, p. 2 · TI 40/1994, p. 3 — Sections1.1–1.2, full service note, exploded drawing and summary3.1.
Part numbers (14)
- 1207 648 0400 — Original sprocket coverProhibited with friction clutch · E20 friction-clutch configuration; restrictions above
- 1207 648 0405 — Revised sprocket coverRequired; also fits old configuration per source · E20 friction-clutch configuration; restrictions above
- 1207 640 7500 — Original gearwheelOld · E20 friction-clutch configuration; restrictions above
- 1207 640 7505 — Revised gearwheelRequired for retrofit · E20 friction-clutch configuration; restrictions above
- 1207 640 2050 — Complete sprocket 3/8 inch 8TSprocket plus new collar screw · E20 friction-clutch configuration; restrictions above
- 1207 640 2051 — Complete sprocket .325 inch 8TSprocket plus new collar screw · E20 friction-clutch configuration; restrictions above
- 1207 642 1310 — Old sprocket 3/8 inch 8TOlder keyed configuration · E20 friction-clutch configuration; restrictions above
- 1207 642 1311 — Old sprocket .325 inch 8TOlder keyed configuration · E20 friction-clutch configuration; restrictions above
- 1207 162 4200 — Left-hand-thread collar screwRenew with sprocket · E20 friction-clutch configuration; restrictions above
- 1207 007 1002 — Cup spring and washer setTwo washers and three springs · E20 friction-clutch configuration; restrictions above
- 1207 162 8900 — WasherTwo required · E20 friction-clutch configuration; restrictions above
- 9485 648 2044 — Cup springThree; replace as set · E20 friction-clutch configuration; restrictions above
- 0000 958 1218 — Original washerRetained for older machines · E20 friction-clutch configuration; restrictions above
- 9460 624 1001 — Original E-clipRetained for older machines · E20 friction-clutch configuration; restrictions above
Service note · E 14 / E 20 / E 140 / E 180 C
E 14 / E 20 / E 140 / E 180 C: metal-housing replacement oil pump
The bulletin explicitly permits pump 1208 640 3250 in the older E 14 and E 20.
- Section 1.2 describes a METAL pump housing. Oil pump 1208 640 3250 is supplied as a replacement part for the new saws and can ALSO be installed in E 14 and E 20.
- This is a complete oil-pump fitment statement, not authority to swap individual pump internals, gear housings or brakes. No previous pump number, modification, oil-output specification or serial restriction is printed.
- The exact numbered pump appears on the E 14 sheet C (oil pump/chain brake), E 20/E 220 sheet C (oil pump/chain brake) and E 140/E 160/E 180 C sheet B (gear housing/oil pump). Shared sheet labels do NOT add E 220, E 160 or MSE fitment to this bulletin assertion. Factory spare supply in 1997 is not current availability.
- TI02/1997 provides no serial cutoff. Shared catalog sheets do not extend this note to unnamed models, MSE successors or other voltage versions. No hardware operation was performed.
Source: TI 2/1997, p. 2 — E 14 / E 20 / E 140 / E 180 C: metal-housing replacement oil pump.
Part numbers (1)
- 1208 640 3250 — Oil pump with metal housingreplacement; expressly also fits E 14 and E 20 · E 140 and E 180 C context; E 14 and E 20 explicitly named
Wrong number or missing part for the E 20, E 220? Report a correction →