← E140/E160/E180 · MSE 140/141/160/180/200

Stihl 1208 · Section A · 1 of 4 · 37 parts

Electric motor

Fits E 140, E 160, E 180 C.

Parts diagrams →

Historical fitment & changes (11) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
110131415161718220212223242526273456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (37)

PosPart numberDescriptionQty
1 1208 602 1201 Motor housing 1
2 0000 988 6115 Plug 1
3 1208 600 0100 Stator 230/240 V 1
3 1208 600 0101 Stator 230/240 V 1
3 1206 600 0100 Stator 230 V 1
3 1208 600 0105 Stator 120 V 1
3 1208 600 0115 Stator 120 V 1
4 9074 478 3525 Pan head self-tapping screw IS-P4.5x45 2
4 9074 478 3555 Pan head self-tapping screw IS-P4.5x55 2
5 1208 084 1801 Air guide ring 1
6 1208 600 1000 Rotor 230/240 V 1
6 1208 600 1005 Rotor 230/240 V 1
6 1208 600 1010 Rotor with fanwheel 120 V 1
6 1208 600 1015 Rotor with fanwheel 120 V 1
7 1208 086 0500 Fanwheel 1
8 9503 003 9670 Grooved ball bearing 608-2Z 1
9 1206 608 1200 Washer 1
10 1206 435 0310 Quick-action switch 1
13 1206 605 1001 Capacitor 230/240 V 1
13 1208 605 1000 Capacitor 120 V 1
14 1207 440 2000 Connecting cable 230 V 1
15 1208 440 2001 Connecting cable 230 V 1
16 1207 440 2001 Connecting cable 230 V 1
17 1207 440 2003 Connecting cable 120 V 1
18 1204 431 2400 Cable protector 1
20 1208 430 1515 Overload cutout 230/240 V 1
20 1208 430 1500 Overload cutout 120 V 1
20 1208 430 1520 Overload cutout 230/240 V 1
20 1208 430 1525 Overload cutout 230/240 V 1
20 1208 430 1510 Overload cutout 120 V 1
21 1206 435 8000 Sealing washer 1
22 1204 431 2500 Cable clamp 1
23 9074 478 3075 Pan head self-tapping screw IS-P4x19 2
24 1206 600 2601 Brush holder 120 V 2
25 1208 007 1001 Set of brush holder 230/240 V 1
26 1206 007 1001 Set of carbon brushes 120 V 1
27 not sold separately Carbon brush 230/240 V not available as a separate item 2

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · E 180 C

E 180 C: overload interruption and carbon-brush cut-out

Two electrical protection functions are distinct from the mechanical coasting brake.

  • The E 180 C is equipped with an overload circuit-breaker intended to interrupt power in the event of MECHANICAL OVERLOAD.
  • A separate automatic carbon-brush cut-out interrupts power when the printed brush wear limit of approximately 10 mm (0.4 in) is reached. The bulletin does not define a measuring datum, new-brush length, reset sequence or adjustment; do not interpret 10 mm as an amount to remove.
  • These statements are expressly for E 180 C. They do not establish the presence or absence of these functions on E 140 or E 160; the later manual must be reviewed separately for those claims. No bypass or energized test procedure is supplied.
  • TI02/1997 provides no serial cutoff. Shared catalog sheets do not extend this note to unnamed models, MSE successors or other voltage versions. No hardware operation was performed.

Source: TI 2/1997, p. 1 — E 180 C: overload interruption and carbon-brush cut-out.

No additional parts-table entry added.

Service note · E 140 / E 180 C

E 140 / E 180 C: universal motor, ring gear and oil-pump drive

The drive principle is compared with E 14 and E 20, not declared component interchange.

  • Figure 100TI002 KN: pinion (1) on the universal-motor rotor (2) drives ring gear (3). Chain sprocket (4) is mounted on the ring gear shaft. Spur gear (5) drives the oil pump.
  • The text calls this the same PRINCIPLE as E 14 and E 20. That does not specify identical ratios, part numbers, electrical versions or a motor/gear substitution. Drawing callouts 1–5 are not IPL positions or assembly inclusion quantities.
  • TI02/1997 provides no serial cutoff. Shared catalog sheets do not extend this note to unnamed models, MSE successors or other voltage versions. No hardware operation was performed.

Source: TI 2/1997, p. 2 — E 140 / E 180 C: universal motor, ring gear and oil-pump drive.

No additional parts-table entry added.

Service note · E 140 / E 180 C

E 140 / E 180 C: changed brake and stator repairs require the dedicated manual

E 14 repair times carry over; E 14/E 20 brake and stator procedures do not.

  • Section 2 warns that the new service manual’s CHAIN BRAKE and STATOR procedures differ considerably from E 14 and E 20. Use the model-appropriate chapters; do not substitute the predecessor repair procedure merely because the drive principle is similar.
  • The manual lists service accessories, special tools and aids. Scoped later 2003 stator/brake/access/oil-pump/gear-housing chapters and 2012 exact-model tools are reviewed. These later sources are NOT the exact 1997 manual. Five original-source gaps are documented; no locally actionable dependency remains for this TI scope.
  • If the unit is started during repair or maintenance, the bulletin requires applicable local regulations and the owner’s-manual safety precautions. This historical instruction is not permission to energize hardware; the exact operator instructions remain an explicitly documented source gap.
  • The repair TIMES specified for E 14 also apply to E 140 and E 180 C. No operation-specific time values are printed here, and this administrative equivalence does NOT make the old brake/stator procedures applicable.
  • TI02/1997 provides no serial cutoff. Shared catalog sheets do not extend this note to unnamed models, MSE successors or other voltage versions. No hardware operation was performed.

Source: TI 2/1997, p. 3 — E 140 / E 180 C: changed brake and stator repairs require the dedicated manual.

No additional parts-table entry added.

Service note · E 140

E 140: 120 V / 60 Hz specifications and cutting attachment

The complete printed column retains load conditions, measurement location and original units.

  • Electrical data: motor 1.4 kW; rated voltage 120 V; frequency 60 Hz; protection class printed “Type II”; enclosure IP 20. Current drawn at NO LOAD WITHOUT CUTTING ATTACHMENT: 6.0 A. The listed 120 V fuse is 15 A; no alternate-voltage rating or loaded-current limit is inferred.
  • Speeds WITH CUTTING ATTACHMENT: 4900 rpm on load and 6100 rpm at no load. Footnote 1 identifies CHAIN-SPROCKET speed, NOT rotor speed or chain linear velocity. Do not mix these speed conditions with the attachment-free current measurement.
  • Sound-pressure level Lp, WITHOUT LOAD, to the printed ANSI B175.3 reference: 69 dB(A) at 50 ft and 93 dB(A) at the operator’s ear. These are pressure levels at two locations, not sound-power values or exposure guarantees; the printed standard identifier is retained without silently correcting it.
  • Oil tank capacity 6.8 oz (source does not further qualify the ounce convention). Weight 7.1 lb WITHOUT CUTTING ATTACHMENT AND WITHOUT CONNECTING CORD. Tensioning: front chain tensioner. Connecting-cord length for 120 V: 11.8 in. These are historical printed values, not measurements of an owner’s saw.
  • Section 4 cutting attachment: 3/8 in Picco Micro Narrow; guide bar/cutting length Rollomatic Mini / 12 in. No drive-link count, groove gauge, mount code, chain order number or universal bar-compatibility list is supplied; do not infer them from the trade names.
  • TI02/1997 provides no serial cutoff. Shared catalog sheets do not extend this note to unnamed models, MSE successors or other voltage versions. No hardware operation was performed.

Source: TI 2/1997, p. 4 — E 140: 120 V / 60 Hz specifications and cutting attachment.

No additional parts-table entry added.

Service note · E 180 C

E 180 C: 120 V / 60 Hz specifications and cutting attachment

The complete printed column retains load conditions, measurement location and original units.

  • Electrical data: motor 1.8 kW; rated voltage 120 V; frequency 60 Hz; protection class printed “Type II”; enclosure IP 20. Current drawn at NO LOAD WITHOUT CUTTING ATTACHMENT: 8.2 A. The listed 120 V fuse is 15 A; no alternate-voltage rating or loaded-current limit is inferred.
  • Speeds WITH CUTTING ATTACHMENT: 5000 rpm on load and 6800 rpm at no load. Footnote 1 identifies CHAIN-SPROCKET speed, NOT rotor speed or chain linear velocity. Do not mix these speed conditions with the attachment-free current measurement.
  • Sound-pressure level Lp, WITHOUT LOAD, to the printed ANSI B175.3 reference: 68 dB(A) at 50 ft and 93 dB(A) at the operator’s ear. These are pressure levels at two locations, not sound-power values or exposure guarantees; the printed standard identifier is retained without silently correcting it.
  • Oil tank capacity 6.8 oz (source does not further qualify the ounce convention). Weight 7.7 lb WITHOUT CUTTING ATTACHMENT AND WITHOUT CONNECTING CORD. Tensioning: quick chain tensioner. Connecting-cord length for 120 V: 11.8 in. These are historical printed values, not measurements of an owner’s saw.
  • Section 4 cutting attachment: 3/8 in Picco Micro 1; guide bar/cutting length Rollomatic 3/8 P / 14 in. No drive-link count, groove gauge, mount code, chain order number or universal bar-compatibility list is supplied; do not infer them from the trade names.
  • TI02/1997 provides no serial cutoff. Shared catalog sheets do not extend this note to unnamed models, MSE successors or other voltage versions. No hardware operation was performed.

Source: TI 2/1997, p. 4 — E 180 C: 120 V / 60 Hz specifications and cutting attachment.

No additional parts-table entry added.

Service note · E 140 / E 160 / E 180 C

E-series rotor access: preserve reused carbon-brush positions

Serious commutator scoring is not cured by swapping brush locations.

  • Later-source comparison: RA_100_00_01_02, cover 2003-01, contents copyright 1998, production stamp 2006-03-02. Its introduction expressly covers E 140, E 160 and E 180 C with model-specific exceptions. This is NOT proof of the exact manual supplied in 1997, MSE applicability or electrical-version interchange.
  • Section 5.1 removes the commutator cover, disconnects the wire from the tag and draws the brush holder forward. If brushes can be reused, DO NOT CHANGE their installed positions.
  • Inspect commutator before refitting; serious scoring causes increased sparking and can require rotor replacement. Verify each brush moves freely in its holder and that top/bottom holder lugs enter housing slots; reconnect wire and refit cover at 3.0 Nm (2.2 lbf.ft).
  • This section does not define the datum for TI02/1997’s approximately 10 mm brush cut-out statement. No minimum brush length or energized sparking test is invented.
  • No hardware operation was performed. Unplug before repair; the manual requires post-repair high-voltage insulation testing by electricians or specially trained personnel. This source summary does not provide missing test voltage/duration/acceptance values or establish a verified repair.

TI dependency: TI 2/1997, p. 3 — E-series rotor access: preserve reused carbon-brush positions.

Later manual evidence: STIHL E 140, E 160, E 180 C service manual (2003-01), section E-series rotor access: preserve reused carbon-brush positions, PDF pages 3, 7, 11

No parts-table entry added. Tool references, where present, are retained in the manual notes above.

Service note · E 140 / E 160 / E 180 C

E-series rotor: left-hand pinion nut and two spring locations

The pinion nut uses Loctite 242; the brake drum uses a different retaining compound.

  • Later-source comparison: RA_100_00_01_02, cover 2003-01, contents copyright 1998, production stamp 2006-03-02. Its introduction expressly covers E 140, E 160 and E 180 C with model-specific exceptions. This is NOT proof of the exact manual supplied in 1997, MSE applicability or electrical-version interchange.
  • Section 5.2 prerequisites: remove carbon brushes (5.1), oil tank (9.1), ring gear and spur gear (6.2). Remove hand guard, disconnect chain-brake switch tags, then remove gear housing while drawing rotor from stator. Disconnect tension springs.
  • Heat the pinion mounting nut with hot air, hold pinion steady, and release the slotted nut’s LEFT-HAND THREAD in the illustrated direction. Protect polymer components. Pry pinion off shaft and withdraw rotor from ball bearing; do not infer right-hand loosening from a generic fastener rule.
  • Inspect rotor core, commutator, drum, fanwheel and bearing. Minor commutator marks may be dressed with emery cloth; severe marks require a new rotor. A replaced drum also requires brake-band inspection. A serviceable drum’s friction surface is cleaned/roughened with approximately 120 µm abrasive grain, NOT a claimed P120 grit grade.
  • Clean nut thread and rotor stub using solvent-based degreasant containing no chlorinated or halogenated hydrocarbons. Coat slotted nut thread with Loctite 242 (10.2 and torque-table footnote), hold pinion and tighten to 8.0 Nm (5.9 lbf.ft). Do not substitute drum-retaining Loctite 648.
  • Reassembly: SMALLER spring attaches to BRAKE LEVER (100RA040); LARGER spring hooks to PIVOT PIN using tube 1117 890 0900 (100RA042). Gear-housing screws: 3.0 Nm (2.2 lbf.ft); hand-guard screw: 4.5 Nm (3.3 lbf.ft). These are separate from stator and brake-band torque rows.
  • No hardware operation was performed. Unplug before repair; the manual requires post-repair high-voltage insulation testing by electricians or specially trained personnel. This source summary does not provide missing test voltage/duration/acceptance values or establish a verified repair.

TI dependency: TI 2/1997, p. 3 — E-series rotor: left-hand pinion nut and two spring locations.

Later manual evidence: STIHL E 140, E 160, E 180 C service manual (2003-01), section E-series rotor: left-hand pinion nut and two spring locations, PDF pages 3, 5, 7, 12, 13, 24

Part numbers (2)
  • 1117 890 0900 — Assembly tubeLater manual service reference · Attach larger spring to pivot pin; exact later E-series manual scope
  • 0786 111 1101 — Loctite 242Later manual service reference · Slotted pinion nut thread; exact later E-series manual scope

Service note · E 140 / E 160 / E 180 C

E-series rotor bearings: shaft bearing versus gear-housing bearing

The manual distinguishes a replaceable shaft bearing from a housing replacement instruction.

  • Later-source comparison: RA_100_00_01_02, cover 2003-01, contents copyright 1998, production stamp 2006-03-02. Its introduction expressly covers E 140, E 160 and E 180 C with model-specific exceptions. This is NOT proof of the exact manual supplied in 1997, MSE applicability or electrical-version interchange.
  • Section 5.3 removes rotor first, pulls shaft ball bearing off and inspects nylon washer. Refit washer FLAT SIDE AGAINST COMMUTATOR; heat bearing to approximately 50°C (120°F), push to stop and reinstall rotor.
  • For the BALL BEARING IN THE GEAR HOUSING, section 5.3 says a faulty bearing requires a NEW GEAR HOUSING (6.3). This differs from the needle-bearing inspection/replacement instructions in 6.2; do not merge the two bearing types or invent a press-out repair for this ball-bearing seat.
  • Section 6.3’s gear-housing replacement prerequisites include rotor, oil pump and chain brake removal. It prints “oil pump — see 9.2” although the contents and headings place Oil Strainer at 9.2 and Oil Pump at 9.3. This cross-reference conflict is retained; complete pump-removal continuation on PDF 22–23 is now reviewed separately, not silently treated as unavailable.
  • No hardware operation was performed. Unplug before repair; the manual requires post-repair high-voltage insulation testing by electricians or specially trained personnel. This source summary does not provide missing test voltage/duration/acceptance values or establish a verified repair.

TI dependency: TI 2/1997, p. 3 — E-series rotor bearings: shaft bearing versus gear-housing bearing.

Later manual evidence: STIHL E 140, E 160, E 180 C service manual (2003-01), section E-series rotor bearings: shaft bearing versus gear-housing bearing, PDF pages 3, 7, 14, 17

No parts-table entry added. Tool references, where present, are retained in the manual notes above.

Service note · E 140 / E 160 / E 180 C

E-series fanwheel and drum: flange support and shaft-flat adhesive

Brake-drum orientation and support geometry are explicit.

  • Later-source comparison: RA_100_00_01_02, cover 2003-01, contents copyright 1998, production stamp 2006-03-02. Its introduction expressly covers E 140, E 160 and E 180 C with model-specific exceptions. This is NOT proof of the exact manual supplied in 1997, MSE applicability or electrical-version interchange.
  • Section 5.4 removes rotor; support FANWHEEL FLANGE on two flat steel bars, each 5 × 20 × 130 mm, with rotor hanging freely in a press. Heat brake-drum hub with hot air, hold rotor and press it out of drum/fanwheel. No temperature or press-force value is specified for the drum.
  • Clean rotor-shaft stub with the specified non-chlorinated/non-halogenated solvent-based degreasant. Push fanwheel FLANGE FIRST fully onto shaft; coat SHAFT FLATS with Loctite 648, not the slotted pinion-nut thread.
  • Fit drum with CLOSED SIDE TOWARD FANWHEEL. Stand rotor upright with drum at bottom on a socket (19 mm is an example); press rotor down until drum locates against shaft shoulder, then reinstall rotor. These dimensions are support examples/stock sizes, not a complete validated fixture design.
  • No hardware operation was performed. Unplug before repair; the manual requires post-repair high-voltage insulation testing by electricians or specially trained personnel. This source summary does not provide missing test voltage/duration/acceptance values or establish a verified repair.

TI dependency: TI 2/1997, p. 3 — E-series fanwheel and drum: flange support and shaft-flat adhesive.

Later manual evidence: STIHL E 140, E 160, E 180 C service manual (2003-01), section E-series fanwheel and drum: flange support and shaft-flat adhesive, PDF pages 3, 7, 14, 15, 24

Part numbers (1)
  • 0786 110 0126 — Loctite 648Later manual service reference · Brake drum retention on rotor shaft flats; exact later E-series manual scope

Service note · E 140 / E 160 / E 180 C

E-series stator: air baffle, wire protection and unresolved torque units

The procedure continues onto printed page 15; page 14 alone is incomplete.

  • Later-source comparison: RA_100_00_01_02, cover 2003-01, contents copyright 1998, production stamp 2006-03-02. Its introduction expressly covers E 140, E 160 and E 180 C with model-specific exceptions. This is NOT proof of the exact manual supplied in 1997, MSE applicability or electrical-version interchange.
  • Section 5.5 follows rotor removal (5.2): remove air baffle; release screw at switch, withdraw wires and CUT OFF END FERRULE; remove stator mounting screws and press stator out. Do not infer reusable ferrule, connector size or crimp geometry from the diagram.
  • Inspect field-coil insulation; replace stator if damaged. Inspect inner running surface and replace if necessary. These are inspection instructions, not a supplied winding-resistance limit or test voltage.
  • Position stator and use screwdriver 5910 890 2400 to press it fully home. DO NOT PINCH CARBON-BRUSH WIRES. The procedure then refits screws and reverses removal; no alternate motor/voltage interchange is established.
  • UNRESOLVED SOURCE CONFLICT: procedure prints 3.0 Nm (3.0 lbf.ft); these units are not equivalent. The torque table repeats 3.0/3.0 on stator rows labeled 1200 W (IS-P4.5x45) and 1400, 1600 W (IS-P4.5x55), while this manual’s model scope includes 1800 W E 180 C. Preserve the numeric conflict and power-label gap; do not silently relabel 1200 W or assign either screw length to E 180 C.
  • Crimping tool 5910 890 8210 is listed for electrical connectors, but no ferrule specification is given here. The missing reconnection/test detail is not permission to improvise a mains-wiring repair.
  • No hardware operation was performed. Unplug before repair; the manual requires post-repair high-voltage insulation testing by electricians or specially trained personnel. This source summary does not provide missing test voltage/duration/acceptance values or establish a verified repair.

TI dependency: TI 2/1997, p. 3 — E-series stator: air baffle, wire protection and unresolved torque units.

Later manual evidence: STIHL E 140, E 160, E 180 C service manual (2003-01), section E-series stator: air baffle, wire protection and unresolved torque units, PDF pages 3, 5, 7, 15, 16, 24

Part numbers (2)
  • 5910 890 2400 — QI-T27x150 T-handle screwdriverLater manual service reference · Press stator home; releasing IS screws; exact later E-series manual scope
  • 5910 890 8210 — Crimping toolLater manual service reference · Attach connectors to electrical wires; no ferrule size supplied; exact later E-series manual scope

Service note · E 140 / E 160 / E 180 C

E-series polymer fasteners: re-engage the existing thread

Power-driver ceilings are not substitutes for a torque wrench.

  • Later-source comparison: RA_100_00_01_02, cover 2003-01, contents copyright 1998, production stamp 2006-03-02. Its introduction expressly covers E 140, E 160 and E 180 C with model-specific exceptions. This is NOT proof of the exact manual supplied in 1997, MSE applicability or electrical-version interchange.
  • Section 2.4 requires torque wrench use for Plastoform screws. In an existing thread, rotate P screw COUNTERCLOCKWISE until it drops slightly, then tighten clockwise to specified torque; this is intended to re-engage the existing thread, not form a new one.
  • Printed power-driver speed ceilings in polymer: Plastoform maximum 600 rpm; DG maximum 500 rpm. These are different screw families, not generic motor rpm limits.
  • Hot-air warming can ease release of adhesive-secured screws/nuts; the manual warns to protect polymer components. The tool-table footnote restricts the indicated hand screwdrivers to RELEASING ONLY on Plastoform screws; tightening still requires torque control.
  • No hardware operation was performed. Unplug before repair; the manual requires post-repair high-voltage insulation testing by electricians or specially trained personnel. This source summary does not provide missing test voltage/duration/acceptance values or establish a verified repair.

TI dependency: TI 2/1997, p. 3 — E-series polymer fasteners: re-engage the existing thread.

Later manual evidence: STIHL E 140, E 160, E 180 C service manual (2003-01), section E-series polymer fasteners: re-engage the existing thread, PDF pages 3, 5, 7, 24

No parts-table entry added. Tool references, where present, are retained in the manual notes above.

Wrong number or missing part for the E 140, E 160, E 180 C? Report a correction →