Stihl 1208 · Section B · 2 of 4 · 25 parts
Gear housing, Oil pump
Fits E 140, E 160, E 180 C.
Historical fitment & changes (15) — includes parts and conditions not shown on this drawing.
Parts (25)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 1208 640 0503 | Gear housing | 1 |
| 2 | 9513 003 1920 | Needle cage 8x12x10 | 1 |
| 3 | 9645 945 7457 | O-ring 5x1.5 | 2 |
| 4 | 1208 640 3250 | Oil pump Fitment / change note → | 1 |
| 5 | 1208 640 3000 | Pump housing | 1 |
| 6 | 1206 640 4700 | Pump piston | 1 |
| 7 | 9517 003 5060 | Cylindrical roller 4x10.8 | 1 |
| 8 | 9074 478 3075 | Pan head self-tapping screw IS-P4x19 | 2 |
| 9 | 0000 958 0504 | Washer | 1 |
| 10 | 1116 647 1806 | Spur gear | 1 |
| 11 | 1123 162 7800 | Flat spring | 1 |
| 12 | 1208 162 3201 | Carrier | 1 |
| 13 | 1208 160 5000 | Lever | 1 |
| 14 | 1208 160 5405 | Brake band | 1 |
| 15 | 9079 319 1350 | Flat head screw M6x25 | 1 |
| 16 | 1208 162 7900 | Tension spring | 1 |
| 17 | 1208 162 7910 | Tension spring | 1 |
| 18 | 1208 435 2401 | Trigger switch | 1 |
| 19 | 1208 435 2500 | Pawl | 1 |
| 20 | 0000 998 1112 | Torsion spring | 1 |
| 21 | 1208 162 1500 | Brake rod | 1 |
| 22 | 9645 945 7457 | O-ring 5x1.5 | 1 |
| 23 | 1117 647 6801 | Strainer | 1 |
| 24 | 9074 478 4135 | Pan head self-tapping screw IS-P5x20 | 3 |
| 25 | 1208 160 2400 | Brake drum | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · E 140 / E 180 C
E 140 / E 180 C: universal motor, ring gear and oil-pump drive
The drive principle is compared with E 14 and E 20, not declared component interchange.
- Figure 100TI002 KN: pinion (1) on the universal-motor rotor (2) drives ring gear (3). Chain sprocket (4) is mounted on the ring gear shaft. Spur gear (5) drives the oil pump.
- The text calls this the same PRINCIPLE as E 14 and E 20. That does not specify identical ratios, part numbers, electrical versions or a motor/gear substitution. Drawing callouts 1–5 are not IPL positions or assembly inclusion quantities.
- TI02/1997 provides no serial cutoff. Shared catalog sheets do not extend this note to unnamed models, MSE successors or other voltage versions. No hardware operation was performed.
Source: TI 2/1997, p. 2 — E 140 / E 180 C: universal motor, ring gear and oil-pump drive.
No additional parts-table entry added.
Service note · E 14 / E 20 / E 140 / E 180 C
E 14 / E 20 / E 140 / E 180 C: metal-housing replacement oil pump
The bulletin explicitly permits pump 1208 640 3250 in the older E 14 and E 20.
- Section 1.2 describes a METAL pump housing. Oil pump 1208 640 3250 is supplied as a replacement part for the new saws and can ALSO be installed in E 14 and E 20.
- This is a complete oil-pump fitment statement, not authority to swap individual pump internals, gear housings or brakes. No previous pump number, modification, oil-output specification or serial restriction is printed.
- The exact numbered pump appears on the E 14 sheet C (oil pump/chain brake), E 20/E 220 sheet C (oil pump/chain brake) and E 140/E 160/E 180 C sheet B (gear housing/oil pump). Shared sheet labels do NOT add E 220, E 160 or MSE fitment to this bulletin assertion. Factory spare supply in 1997 is not current availability.
- TI02/1997 provides no serial cutoff. Shared catalog sheets do not extend this note to unnamed models, MSE successors or other voltage versions. No hardware operation was performed.
Source: TI 2/1997, p. 2 — E 14 / E 20 / E 140 / E 180 C: metal-housing replacement oil pump.
Part numbers (1)
- 1208 640 3250 — Oil pump with metal housingreplacement; expressly also fits E 14 and E 20 · E 140 and E 180 C context; E 14 and E 20 explicitly named
Service note · E 140 / E 180 C
E 140 / E 180 C: coasting brake and inertia chain brake
Releasing the trigger applies the mechanical coasting brake; the off-state drum is locked.
- Section 1.3 describes a mechanical coasting brake INTEGRATED WITH an inertia chain brake. It is intended to stop the chain when the trigger is released. When the unit is off, the coasting brake locks the brake drum; squeezing the trigger releases the brake band from the drum.
- Figure 100TI003 KN identifies (1) coasting-brake spring, (2) chain-brake switch, (3) chain-brake spring, (4) brake band, (5) brake drum and (6) trigger switch. Keep the TWO springs and the electrical chain-brake switch distinct. Callouts are not replacement-part numbers.
- The diagram explains function only: no stopping-time limit, spring adjustment, permissible band wear or test sequence is given. It does not show that squeezing the trigger overrides an applied inertia brake. The dedicated brake chapter remains a separate repair dependency.
- TI02/1997 provides no serial cutoff. Shared catalog sheets do not extend this note to unnamed models, MSE successors or other voltage versions. No hardware operation was performed.
Source: TI 2/1997, p. 1 · TI 2/1997, p. 3 — E 140 / E 180 C: coasting brake and inertia chain brake.
No additional parts-table entry added.
Service note · E 140 / E 180 C
E 140 / E 180 C: changed brake and stator repairs require the dedicated manual
E 14 repair times carry over; E 14/E 20 brake and stator procedures do not.
- Section 2 warns that the new service manual’s CHAIN BRAKE and STATOR procedures differ considerably from E 14 and E 20. Use the model-appropriate chapters; do not substitute the predecessor repair procedure merely because the drive principle is similar.
- The manual lists service accessories, special tools and aids. Scoped later 2003 stator/brake/access/oil-pump/gear-housing chapters and 2012 exact-model tools are reviewed. These later sources are NOT the exact 1997 manual. Five original-source gaps are documented; no locally actionable dependency remains for this TI scope.
- If the unit is started during repair or maintenance, the bulletin requires applicable local regulations and the owner’s-manual safety precautions. This historical instruction is not permission to energize hardware; the exact operator instructions remain an explicitly documented source gap.
- The repair TIMES specified for E 14 also apply to E 140 and E 180 C. No operation-specific time values are printed here, and this administrative equivalence does NOT make the old brake/stator procedures applicable.
- TI02/1997 provides no serial cutoff. Shared catalog sheets do not extend this note to unnamed models, MSE successors or other voltage versions. No hardware operation was performed.
Source: TI 2/1997, p. 3 — E 140 / E 180 C: changed brake and stator repairs require the dedicated manual.
No additional parts-table entry added.
Service note · E 140 / E 160 / E 180 C
E-series handle access: needle sleeve support and oil-tank seals
Keep removal and installation support sides distinct.
- Later-source comparison: RA_100_00_01_02, cover 2003-01, contents copyright 1998, production stamp 2006-03-02. Its introduction expressly covers E 140, E 160 and E 180 C with model-specific exceptions. This is NOT proof of the exact manual supplied in 1997, MSE applicability or electrical-version interchange.
- Section 4.1 removes the quick tensioner if fitted (7.3); unfold its wingnut handle, unscrew and remove the sprocket cover. The wingnut can be eased out and refitted until it snaps into the cover. Models with quick tensioner also require removal of the spiked bumper; do not silently apply this step to every variant.
- For all models, 6.1 removes the E-clip and outer washer, chain sprocket, then inner washer. Section 4.1 removes oil filler cap with retainer, housing screws and handle housing. For needle-sleeve removal, remove O-ring and support the bearing bush FROM OUTSIDE using a socket (19 mm is an example); press with drift 1111 893 4700.
- For refitting, use a NEW O-ring on the gear-housing pivot pin. Support the bush FROM INSIDE with a socket and install needle sleeve with arbor 4116 893 7205. Inspect oil-tank sealing ring and replace if necessary. Handle-housing screws: 2.0 Nm (1.5 lbf.ft).
- Section 9.1 removes the oil tank after handle-housing access, pulling it off the strainer at the same time; remove sealing ring and grommet, refit in reverse. Section 9.2 pulls strainer off stub, cleans and inspects it, replacing if damaged. This is not an oil-pump output test or pump-overhaul closure.
- The adjacent cord-replacement steps are not required merely to access the rotor. If cord work is performed, 4.1 removes clamp screws and switch wires, transfers protector THIN END FIRST, checks its seating and tightens strain-relief clamp to 1.5 Nm (1.1 lbf.ft). No invented conductor length, ferrule size or switch-terminal torque is supplied.
- No hardware operation was performed. Unplug before repair; the manual requires post-repair high-voltage insulation testing by electricians or specially trained personnel. This source summary does not provide missing test voltage/duration/acceptance values or establish a verified repair.
TI dependency: TI 2/1997, p. 3 — E-series handle access: needle sleeve support and oil-tank seals.
Later manual evidence: STIHL E 140, E 160, E 180 C service manual (2003-01), section E-series handle access: needle sleeve support and oil-tank seals, PDF pages 3, 7, 8, 16, 19, 22
Part numbers (2)
- 1111 893 4700 — Assembly driftLater manual service reference · Needle sleeve removal; exact later E-series manual scope
- 4116 893 7205 — Press arborLater manual service reference · Needle sleeve installation; exact later E-series manual scope
Service note · E 140 / E 160 / E 180 C
E-series rotor: left-hand pinion nut and two spring locations
The pinion nut uses Loctite 242; the brake drum uses a different retaining compound.
- Later-source comparison: RA_100_00_01_02, cover 2003-01, contents copyright 1998, production stamp 2006-03-02. Its introduction expressly covers E 140, E 160 and E 180 C with model-specific exceptions. This is NOT proof of the exact manual supplied in 1997, MSE applicability or electrical-version interchange.
- Section 5.2 prerequisites: remove carbon brushes (5.1), oil tank (9.1), ring gear and spur gear (6.2). Remove hand guard, disconnect chain-brake switch tags, then remove gear housing while drawing rotor from stator. Disconnect tension springs.
- Heat the pinion mounting nut with hot air, hold pinion steady, and release the slotted nut’s LEFT-HAND THREAD in the illustrated direction. Protect polymer components. Pry pinion off shaft and withdraw rotor from ball bearing; do not infer right-hand loosening from a generic fastener rule.
- Inspect rotor core, commutator, drum, fanwheel and bearing. Minor commutator marks may be dressed with emery cloth; severe marks require a new rotor. A replaced drum also requires brake-band inspection. A serviceable drum’s friction surface is cleaned/roughened with approximately 120 µm abrasive grain, NOT a claimed P120 grit grade.
- Clean nut thread and rotor stub using solvent-based degreasant containing no chlorinated or halogenated hydrocarbons. Coat slotted nut thread with Loctite 242 (10.2 and torque-table footnote), hold pinion and tighten to 8.0 Nm (5.9 lbf.ft). Do not substitute drum-retaining Loctite 648.
- Reassembly: SMALLER spring attaches to BRAKE LEVER (100RA040); LARGER spring hooks to PIVOT PIN using tube 1117 890 0900 (100RA042). Gear-housing screws: 3.0 Nm (2.2 lbf.ft); hand-guard screw: 4.5 Nm (3.3 lbf.ft). These are separate from stator and brake-band torque rows.
- No hardware operation was performed. Unplug before repair; the manual requires post-repair high-voltage insulation testing by electricians or specially trained personnel. This source summary does not provide missing test voltage/duration/acceptance values or establish a verified repair.
TI dependency: TI 2/1997, p. 3 — E-series rotor: left-hand pinion nut and two spring locations.
Later manual evidence: STIHL E 140, E 160, E 180 C service manual (2003-01), section E-series rotor: left-hand pinion nut and two spring locations, PDF pages 3, 5, 7, 12, 13, 24
Part numbers (2)
- 1117 890 0900 — Assembly tubeLater manual service reference · Attach larger spring to pivot pin; exact later E-series manual scope
- 0786 111 1101 — Loctite 242Later manual service reference · Slotted pinion nut thread; exact later E-series manual scope
Service note · E 140 / E 160 / E 180 C
E-series rotor bearings: shaft bearing versus gear-housing bearing
The manual distinguishes a replaceable shaft bearing from a housing replacement instruction.
- Later-source comparison: RA_100_00_01_02, cover 2003-01, contents copyright 1998, production stamp 2006-03-02. Its introduction expressly covers E 140, E 160 and E 180 C with model-specific exceptions. This is NOT proof of the exact manual supplied in 1997, MSE applicability or electrical-version interchange.
- Section 5.3 removes rotor first, pulls shaft ball bearing off and inspects nylon washer. Refit washer FLAT SIDE AGAINST COMMUTATOR; heat bearing to approximately 50°C (120°F), push to stop and reinstall rotor.
- For the BALL BEARING IN THE GEAR HOUSING, section 5.3 says a faulty bearing requires a NEW GEAR HOUSING (6.3). This differs from the needle-bearing inspection/replacement instructions in 6.2; do not merge the two bearing types or invent a press-out repair for this ball-bearing seat.
- Section 6.3’s gear-housing replacement prerequisites include rotor, oil pump and chain brake removal. It prints “oil pump — see 9.2” although the contents and headings place Oil Strainer at 9.2 and Oil Pump at 9.3. This cross-reference conflict is retained; complete pump-removal continuation on PDF 22–23 is now reviewed separately, not silently treated as unavailable.
- No hardware operation was performed. Unplug before repair; the manual requires post-repair high-voltage insulation testing by electricians or specially trained personnel. This source summary does not provide missing test voltage/duration/acceptance values or establish a verified repair.
TI dependency: TI 2/1997, p. 3 — E-series rotor bearings: shaft bearing versus gear-housing bearing.
Later manual evidence: STIHL E 140, E 160, E 180 C service manual (2003-01), section E-series rotor bearings: shaft bearing versus gear-housing bearing, PDF pages 3, 7, 14, 17
No parts-table entry added. Tool references, where present, are retained in the manual notes above.
Service note · E 140 / E 160 / E 180 C
E-series fanwheel and drum: flange support and shaft-flat adhesive
Brake-drum orientation and support geometry are explicit.
- Later-source comparison: RA_100_00_01_02, cover 2003-01, contents copyright 1998, production stamp 2006-03-02. Its introduction expressly covers E 140, E 160 and E 180 C with model-specific exceptions. This is NOT proof of the exact manual supplied in 1997, MSE applicability or electrical-version interchange.
- Section 5.4 removes rotor; support FANWHEEL FLANGE on two flat steel bars, each 5 × 20 × 130 mm, with rotor hanging freely in a press. Heat brake-drum hub with hot air, hold rotor and press it out of drum/fanwheel. No temperature or press-force value is specified for the drum.
- Clean rotor-shaft stub with the specified non-chlorinated/non-halogenated solvent-based degreasant. Push fanwheel FLANGE FIRST fully onto shaft; coat SHAFT FLATS with Loctite 648, not the slotted pinion-nut thread.
- Fit drum with CLOSED SIDE TOWARD FANWHEEL. Stand rotor upright with drum at bottom on a socket (19 mm is an example); press rotor down until drum locates against shaft shoulder, then reinstall rotor. These dimensions are support examples/stock sizes, not a complete validated fixture design.
- No hardware operation was performed. Unplug before repair; the manual requires post-repair high-voltage insulation testing by electricians or specially trained personnel. This source summary does not provide missing test voltage/duration/acceptance values or establish a verified repair.
TI dependency: TI 2/1997, p. 3 — E-series fanwheel and drum: flange support and shaft-flat adhesive.
Later manual evidence: STIHL E 140, E 160, E 180 C service manual (2003-01), section E-series fanwheel and drum: flange support and shaft-flat adhesive, PDF pages 3, 7, 14, 15, 24
Part numbers (1)
- 0786 110 0126 — Loctite 648Later manual service reference · Brake drum retention on rotor shaft flats; exact later E-series manual scope
Service note · E 140 / E 160 / E 180 C
E-series drive service: pinion and ring gear are a matching set
Thrust washers and the oil-pump spur-gear washer have distinct locations.
- Later-source comparison: RA_100_00_01_02, cover 2003-01, contents copyright 1998, production stamp 2006-03-02. Its introduction expressly covers E 140, E 160 and E 180 C with model-specific exceptions. This is NOT proof of the exact manual supplied in 1997, MSE applicability or electrical-version interchange.
- Section 6.2 follows handle-housing removal. Pull spur gear from oil pump and retain its washer if adhering to gear; remove outer ring-gear thrust washer, withdraw ring gear from housing needle bearing and remove other thrust washer.
- Inspect needle bearings in gear housing and handle housing and replace as required (handle-side procedure in 4.1). ONLY REPLACE PINION AND RING GEAR AS A MATCHING SET (100RA067); no part numbers or ratio changes are stated.
- Refit in reverse; lubricate ring gear and washer and restore oil-pump washer if removed with spur gear. Section 10.2 assigns multipurpose grease 0781 120 1109 to ring gear/washers. Do not confuse this with the two different brake-mechanism grease descriptions or the gear-housing ball-bearing replacement rule.
- No hardware operation was performed. Unplug before repair; the manual requires post-repair high-voltage insulation testing by electricians or specially trained personnel. This source summary does not provide missing test voltage/duration/acceptance values or establish a verified repair.
TI dependency: TI 2/1997, p. 3 — E-series drive service: pinion and ring gear are a matching set.
Later manual evidence: STIHL E 140, E 160, E 180 C service manual (2003-01), section E-series drive service: pinion and ring gear are a matching set, PDF pages 3, 7, 16, 17, 24
Part numbers (1)
- 0781 120 1109 — Multipurpose greaseLater manual service reference · Ring gear and washers; exact later E-series manual scope
Service note · E 140 / E 160 / E 180 C
E-series brake switch lever: pawl and torsion spring orientation
The torsion spring is not either of the two tension springs.
- Later-source comparison: RA_100_00_01_02, cover 2003-01, contents copyright 1998, production stamp 2006-03-02. Its introduction expressly covers E 140, E 160 and E 180 C with model-specific exceptions. This is NOT proof of the exact manual supplied in 1997, MSE applicability or electrical-version interchange.
- Section 8.1 removes gear housing via 5.2 and brake drum via 5.4 IF NECESSARY. Carefully pull switch lever off pivot, disconnect brake rod from pawl, pry pawl from lever and remove torsion spring.
- Refit in reverse and check installed torsion-spring position against 100RA090. Its two indicated seating locations are illustrated; the source gives no angular preload, coil-count adjustment or stand-alone interchange rule.
- The adjacent left-column 7.3 quick-tensioner wingnut instructions belong to cover access, not the brake-pawl assembly. Keep the torsion spring, flat spring and the two tension springs distinct.
- No hardware operation was performed. Unplug before repair; the manual requires post-repair high-voltage insulation testing by electricians or specially trained personnel. This source summary does not provide missing test voltage/duration/acceptance values or establish a verified repair.
TI dependency: TI 2/1997, p. 3 — E-series brake switch lever: pawl and torsion spring orientation.
Later manual evidence: STIHL E 140, E 160, E 180 C service manual (2003-01), section E-series brake switch lever: pawl and torsion spring orientation, PDF pages 3, 7, 19
No parts-table entry added. Tool references, where present, are retained in the manual notes above.
Service note · E 140 / E 160 / E 180 C
E-series brake band: minimum thickness at every point
Preserve the printed wear-list conjunction without weakening the separate minimum-thickness warning.
- Later-source comparison: RA_100_00_01_02, cover 2003-01, contents copyright 1998, production stamp 2006-03-02. Its introduction expressly covers E 140, E 160 and E 180 C with model-specific exceptions. This is NOT proof of the exact manual supplied in 1997, MSE applicability or electrical-version interchange.
- Section 8.1 removes switch lever and rotor first, unhooks brake rod, detaches springs, removes band screw, pries band from housing and unhooks it from brake lever.
- The replacement list prints definite wear on large areas of inside diameter and/or parts of outside diameter AND band thickness less than 0.6 mm (0.025 in). It immediately warns that the band MUST NOT BE THINNER AT ANY POINT. Do not turn the printed AND into permission to keep a locally undersize band, or silently rewrite the source as a validated Boolean test.
- If still serviceable, clean and roughen the ENTIRE INNER FRICTION SURFACE with emery paper/cloth of approximately 120 µm grain size. This is particle size, NOT P120 grit; no thickness-removal allowance or reconditioning of an undersize band is authorized.
- Lift carrier and articulated lever together off bearing pin, separate lever from carrier and remove flat spring. Inspect all parts, ALWAYS replace damaged ones and clean the housing recess. A brake-drum replacement also requires band inspection per 5.2.
- No hardware operation was performed. Unplug before repair; the manual requires post-repair high-voltage insulation testing by electricians or specially trained personnel. This source summary does not provide missing test voltage/duration/acceptance values or establish a verified repair.
TI dependency: TI 2/1997, p. 3 — E-series brake band: minimum thickness at every point.
Later manual evidence: STIHL E 140, E 160, E 180 C service manual (2003-01), section E-series brake band: minimum thickness at every point, PDF pages 3, 7, 13, 20
No parts-table entry added. Tool references, where present, are retained in the manual notes above.
Service note · E 140 / E 160 / E 180 C
E-series brake assembly: flat-spring seating and band-screw torque
The 6.0 Nm value is consistent, but its printed imperial equivalents differ.
- Later-source comparison: RA_100_00_01_02, cover 2003-01, contents copyright 1998, production stamp 2006-03-02. Its introduction expressly covers E 140, E 160 and E 180 C with model-specific exceptions. This is NOT proof of the exact manual supplied in 1997, MSE applicability or electrical-version interchange.
- Section 8.2 lubricates sliding/pivot points with STIHL multipurpose grease or PREFERABLY molybdenum grease (example Molykote). This is not an instruction to grease drum/band friction surfaces.
- Fit flat spring. Fit articulated lever (1) in carrier (2) as 100RA099; position carrier on bearing pin and articulated-lever bore over its separate bearing pin (100RA100). Check flat spring sits on FACE OF BEARING BOSS (100RA101), not merely somewhere under carrier.
- Attach band to brake lever, press band home in gear-housing slots and install fastening screw. Section 8.2 prints 6.0 Nm (4.5 lbf.ft); torque table prints 6.0 Nm (4.4 lbf.ft) for IS-M6x25. Preserve the imperial rounding discrepancy; do not transfer the 3.0 Nm stator/gear-housing value to this screw.
- Reattach springs and brake rod, then reinstall rotor and switch lever by their referenced procedures. There is no stopping-time test or brake acceptance threshold in this section; completed assembly is not verified brake function.
- No hardware operation was performed. Unplug before repair; the manual requires post-repair high-voltage insulation testing by electricians or specially trained personnel. This source summary does not provide missing test voltage/duration/acceptance values or establish a verified repair.
TI dependency: TI 2/1997, p. 3 — E-series brake assembly: flat-spring seating and band-screw torque.
Later manual evidence: STIHL E 140, E 160, E 180 C service manual (2003-01), section E-series brake assembly: flat-spring seating and band-screw torque, PDF pages 3, 5, 7, 21, 24
No parts-table entry added. Tool references, where present, are retained in the manual notes above.
Service note · E 140 / E 160 / E 180 C
E-series polymer fasteners: re-engage the existing thread
Power-driver ceilings are not substitutes for a torque wrench.
- Later-source comparison: RA_100_00_01_02, cover 2003-01, contents copyright 1998, production stamp 2006-03-02. Its introduction expressly covers E 140, E 160 and E 180 C with model-specific exceptions. This is NOT proof of the exact manual supplied in 1997, MSE applicability or electrical-version interchange.
- Section 2.4 requires torque wrench use for Plastoform screws. In an existing thread, rotate P screw COUNTERCLOCKWISE until it drops slightly, then tighten clockwise to specified torque; this is intended to re-engage the existing thread, not form a new one.
- Printed power-driver speed ceilings in polymer: Plastoform maximum 600 rpm; DG maximum 500 rpm. These are different screw families, not generic motor rpm limits.
- Hot-air warming can ease release of adhesive-secured screws/nuts; the manual warns to protect polymer components. The tool-table footnote restricts the indicated hand screwdrivers to RELEASING ONLY on Plastoform screws; tightening still requires torque control.
- No hardware operation was performed. Unplug before repair; the manual requires post-repair high-voltage insulation testing by electricians or specially trained personnel. This source summary does not provide missing test voltage/duration/acceptance values or establish a verified repair.
TI dependency: TI 2/1997, p. 3 — E-series polymer fasteners: re-engage the existing thread.
Later manual evidence: STIHL E 140, E 160, E 180 C service manual (2003-01), section E-series polymer fasteners: re-engage the existing thread, PDF pages 3, 5, 7, 24
No parts-table entry added. Tool references, where present, are retained in the manual notes above.
Service note · E 140 / E 160 / E 180 C
E-series gear housing: remove the brake switch without breaking its snap hook
The oil-pump section-number conflict is retained with the actual continuation.
- Later repair manual: cover 2003-01, contents copyright 1998, production stamp 2006-03-02. Introduction explicitly includes E 140/E 160/E 180 C; this does not establish the exact 1997 manual or extend TI specifications to E 160. Unplug before repair; post-repair high-voltage insulation testing requires electricians or specially trained personnel; missing test parameters remain a source gap.
- Section 6.3 requires rotor removal (5.2), oil pump removal and chain-brake removal (8.1). It prints oil pump — see 9.2, but 9.2 is Oil Strainer; the actual Oil Pump procedure is 9.3 on printed21–22/PDF 22–23. No silent cross-reference correction.
- Lift snap hook (1) A LITTLE, then pull chain-brake switch (2) out as 100RA071. Pull oil strainer off its stub; installation reverses removal. No pry-force limit, switch-contact adjustment or clearance is supplied.
- The gear-housing ball-bearing fault instruction remains NEW GEAR HOUSING (5.3), distinct from replaceable needle bearings. Completing the pump continuation does not authorize a ball-bearing seat repair or validate switch function.
- No hardware operation was performed. This historical source review is not electrical-safety acceptance, a tested fixture or proof of physical interchange.
TI dependency: TI 2/1997, p. 3 — E-series gear housing: remove the brake switch without breaking its snap hook.
Later manual evidence: E 140, E 160, E 180 C service manual (2003-01), section E-series gear housing: remove the brake switch without breaking its snap hook, PDF pages 3, 14, 17, 22, 23
No parts-table entry added. Tool references, where present, are retained in the manual notes above.
Service note · E 140 / E 160 / E 180 C
E-series oil pump: retain its pin, replace O-rings and restore the washer
Pump screws are 2.5 Nm (1.8 lbf.ft), not the gear-housing or stator torque.
- Later repair manual: cover 2003-01, contents copyright 1998, production stamp 2006-03-02. Introduction explicitly includes E 140/E 160/E 180 C; this does not establish the exact 1997 manual or extend TI specifications to E 160. Unplug before repair; post-repair high-voltage insulation testing requires electricians or specially trained personnel; missing test parameters remain a source gap.
- Section 9.3 follows handle-housing removal (4.1). Pull the spur gear from the oil pump; remove the washer if it sticks to the gear, otherwise take the washer out of the pump. Remove pump mounting screws and pull the pump out of the housing. Make sure the pin does not fall out.
- Remove the O-rings and ALWAYS USE NEW O-RINGS on assembly. If the pin has fallen out, refit it with lubricating grease; 10.2 names 0781 120 1111 for the oil-pump pin. Do not infer an O-ring size, pin orientation, internal adjustment or pump-overhaul method absent from this section.
- Install in reverse; tighten pump mounting screws to 2.5 Nm (1.8 lbf.ft) and fit the washer in the pump before restoring the spur gear. This is not the 3.0 Nm gear-housing value. The drawings 100RA106/109 identify the same washer location, not two additional washers.
- The manual gives no oil-output acceptance limit here. TI02/1997 separately identifies complete pump 1208 640 3250 for E 140/E 180 C and earlier E 14/E 20; this later procedure does not enlarge that TI part-number fitment to E 160, MSE or every electrical version.
- No hardware operation was performed. This historical source review is not electrical-safety acceptance, a tested fixture or proof of physical interchange.
TI dependency: TI 2/1997, p. 3 — E-series oil pump: retain its pin, replace O-rings and restore the washer.
Later manual evidence: E 140, E 160, E 180 C service manual (2003-01), section E-series oil pump: retain its pin, replace O-rings and restore the washer, PDF pages 3, 7, 8, 22, 23, 24
Part numbers (1)
- 0781 120 1111 — Lubricating greaseLater source service reference · Retaining oil-pump pin during refitting; later manual 10.2
Wrong number or missing part for the E 140, E 160, E 180 C? Report a correction →