Stihl 4116 · Section M · 10 of 12 · 32 parts
Gear head
Fits FS 360, FS 420, FS 420 L.
Historical fitment & changes (6) — includes parts and conditions not shown on this drawing.
Parts (32)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4116 640 0510 | Gear housing Fitment / change note → | 1 |
| 2 | 4119 713 6500 | Screw plug Fitment / change note → | 1 |
| 3 | 9291 021 0120 | Washer 5.3 Fitment / change note → | 2 |
| 4 | 9022 341 1070 | Spline screw IS-M5x30 Fitment / change note → | 2 |
| 5 | 4116 640 7301 | Set of pinions M14 Fitment / change note → | 1 |
| 6 | 9503 003 8281 | Grooved ball bearing 6302-2RS Fitment / change note → | 1 |
| 7 | 9503 003 0210 | Grooved ball bearing 6001 | 1 |
| 8 | 9503 003 4950 | Grooved ball bearing 15x32x15 | 1 |
| 9 | 0000 958 1500 | Washer | 1 |
| 10 | 9455 621 1520 | Circlip 15x1 | 1 |
| 11 | 0000 958 3604 | Shim 0.1 mm | 1 |
| 12 | 0000 958 3605 | Shim 0.15 mm | 1 |
| 13 | 0000 958 3002 | Shim 0.2 mm | 1 |
| 14 | 9456 621 4480 | Circlip 42x1.75 | 1 |
| 15 | 9134 381 1230 | Grub screw M6x8 | 1 |
| 16 | 4119 642 7600 | Collar nut M12x1.5 l/h thread Fitment / change note → | 1 |
| 17 | 4116 640 0512 | Gear housing | 1 |
| 18 | 9291 021 0140 | Washer 6.4 Fitment / change note → | 1 |
| 19 | 9022 341 1370 | Spline screw IS-M6x30 | 1 |
| 20 | 4116 640 7301 | Set of pinions M14 Fitment / change note → | 1 |
| 21 | 4116 642 7601 | Collar nut M14x1.5 l/h thread Fitment / change note → | 1 |
| 22 | 4116 710 3800 | Thrust plate Ø 60 mm / 2 3/8" Fitment / change note → | 1 |
| 23 | 4116 717 2800 | Guard washer Ø 60 mm / 2 3/8'' Fitment / change note → | 1 |
| 24 | 4116 713 1600 | Thrust washer Ø 60 mm / 2 3/8" Fitment / change note → | 1 |
| 25 | 4116 713 3100 | Rider plate | 1 |
| 26 | 4119 713 3100 | Rider plate Fitment / change note → | 1 |
| 27 | 4116 710 3810 | Thrust plate Ø 65 mm / 2 9/16" Fitment / change note → | 1 |
| 28 | 4116 717 2810 | Guard washer Ø 65 mm / 2 9/16'' Fitment / change note → | 1 |
| 29 | 4116 717 2702 | Guard ring | 1 |
| 30 | 0781 120 1117 | Gear lubricant 80 g option | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 4116 640 0102 | Gearhead M12 Fitment / change note → | 1 |
| — | 4116 640 0106 | Gearhead M14 | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · FS 360 / FS 420
FS 360 / FS 420: aluminium replacement gearhead and reduced contents
New gearhead excludes tool-mounting parts; its reduced scope of supply does not establish universal cutting-tool compatibility.
- Replacement gearhead and housing change from magnesium alloy to aluminium when the special versions launch (section 3). Output-shaft bearing changes to a higher-heat-resistance version. General introduction is IN PROGRESS, not a single numeric cutoff for every FS 360 and FS 420.
- Old gearhead 4116 640 0101 includes keys 1–9; new 4116 640 0102 includes ONLY 1–5 (MOQ 1). Housing 4116 640 0501 becomes 4116 640 0510, key 1 including keys 2–4 (MOQ 1). Old gearhead and housing are no longer factory available. Bearing 9503 003 8280 becomes 9503 003 8281, key 5, 6302 2RS (MOQ 1); old bearing lasts only while factory stocks remain.
- Unchanged housing items: screw plug 4119 713 6500 (key 2), A5.3 washer 9291 021 0120 (key 3), IS M5x30x22 spline screw 9022 341 1070 (key 4). Blank MOQ cells are not installed quantities. The later IPL shortens the same screw description to M5x30; the longer TI designation remains intact.
- The new replacement gearhead EXCLUDES keys 6–9 and 10–12: both thrust-plate/guard-washer sizes, thrust washer, collar nut and guard ring. The source calls this a universal replacement for all models in context; it does NOT authorize every cutting tool, every STIHL model or replacement of M14 gearheads by the M12 assembly. Figure 340TI001 ties each key to its component; no unprinted torque is inferred.
- Historical TI 48/1994 guidance, not current stock or verified physical interchange. Shared IPL sheets do not extend the named source models or variants. No hardware operation was performed.
Source: TI 48/1994, p. 2 · TI 48/1994, p. 3 — aluminium replacement gearhead and reduced contents.
Part numbers (9)
- 4116 640 0101 — Original gearheadincludes 1–9; no longer factory available · FS 360 / FS 420 only in the configuration described here
- 4116 640 0102 — New replacement gearheadincludes only 1–5; MOQ 1 · FS 360 / FS 420 only in the configuration described here
- 4116 640 0501 — Original gear housingno longer factory available · FS 360 / FS 420 only in the configuration described here
- 4116 640 0510 — Aluminium housing; key 1includes 2–4; MOQ 1 · FS 360 / FS 420 only in the configuration described here
- 4119 713 6500 — Screw plug; key 2unchanged · FS 360 / FS 420 only in the configuration described here
- 9291 021 0120 — Washer A5.3; key 3unchanged · FS 360 / FS 420 only in the configuration described here
- 9022 341 1070 — Spline screw IS M5x30x22; key 4unchanged; later IPL shortens designation · FS 360 / FS 420 only in the configuration described here
- 9503 003 8280 — Original 6302 2RS bearing; key 5while stocks last · FS 360 / FS 420 only in the configuration described here
- 9503 003 8281 — Higher-heat-resistance bearing; key 5MOQ 1 · FS 360 / FS 420 only in the configuration described here
Service note · FS 360 / FS 420
FS 360 / FS 420: special brush-knife mounting and prohibited combinations
The 65 mm thrust plate cannot be installed with the specified deflector or circular-saw limit stops.
X 30 931 757 — ONLY FS 360 special version 4116 011 2305; no FS 420 cutoff supplied.
- New FS 420 special version is for brush-knife applications; an existing FS 360 special version is updated. Both have aluminium housings. The FS 360 change is specifically version 4116 011 2305 from X 30 931 757. No FS 420 serial cutoff is printed. This differs from the clutch cutoff X 30 931 357.
- 65 mm thrust plate 4116 710 3810 replaces 60 mm 4116 710 3800 in these SPECIAL versions; hardened guard ring 4116 717 2700 replaces rider plate 4119 713 3100. Deflector 4116 710 2701 AND limit stops for circular saw blades CANNOT BE INSTALLED TOGETHER WITH THE NEW THRUST PLATE. Do not infer a saw-blade conversion from the general gearhead replacement.
- Unchanged 60 mm components: thrust plate 4116 710 3800 (key 6, includes key 7), guard washer 4116 717 2800 (key 7), thrust washer 4116 713 1600 (key 8), M12x1.5 collar nut 4119 642 7600 (key 9). Their MOQ cells are blank. New 65 mm plate 4116 710 3810 (key 10, includes key 11, MOQ 1), 65 mm washer 4116 717 2810 (key 11, MOQ 5), guard ring 4116 717 2700 (key 12, MOQ 1). ALL are excluded from the new replacement gearhead supply. MOQ 5 is not five installed washers.
- The 2012 linked gearhead IPL lists guard ring 4116 717 2702, whereas this TI specifies 4116 717 2700. The number difference is retained; no supersession or interchangeability between these rings is established here. Product version 4116 011 2305 is a MACHINE identifier, not a component to order.
- Historical TI 48/1994 guidance, not current stock or verified physical interchange. Shared IPL sheets do not extend the named source models or variants. No hardware operation was performed.
Source: TI 48/1994, p. 2 · TI 48/1994, p. 3 — special brush-knife mounting and prohibited combinations.
Part numbers (9)
- 4116 710 3800 — 60 mm thrust plate; key 6includes 7; excluded from new gearhead · FS 360 / FS 420 only in the configuration described here
- 4116 717 2800 — 60 mm guard washer; key 7excluded from new gearhead · FS 360 / FS 420 only in the configuration described here
- 4116 713 1600 — Thrust washer; key 8excluded from new gearhead · FS 360 / FS 420 only in the configuration described here
- 4119 642 7600 — M12x1.5 collar nut; key 9excluded from new gearhead · FS 360 / FS 420 only in the configuration described here
- 4116 710 3810 — 65 mm thrust plate; key 10includes 11; MOQ 1; tool restrictions · FS 360 / FS 420 only in the configuration described here
- 4116 717 2810 — 65 mm guard washer; key 11MOQ 5; excluded from new gearhead · FS 360 / FS 420 only in the configuration described here
- 4116 717 2700 — Hardened guard ring; key 12MOQ 1; distinct from later IPL number · FS 360 / FS 420 only in the configuration described here
- 4119 713 3100 — Rider platereplaced only in described special versions · FS 360 / FS 420 only in the configuration described here
- 4116 710 2701 — Deflectorprohibited with new thrust plate · FS 360 / FS 420 only in the configuration described here
Historical fitment · FS 360
FS 360: M14 gearhead and brush-knife versions
Gearhead 4116 640 0103 uses a 65 mm thrust plate; separate grass deflector cannot be fitted.
- Section 1 describes a new FS 360 version and a revision for special brush-knife applications. BOTH described versions use gearhead 4116 640 0103 with an uprated M14 output shaft, standard 65 mm (2.6 in.) thrust plate 4116 710 3810 and hardened guard ring 4116 717 2700. The plate helps exclude grass and dirt from the gear-housing cavity; a separate grass deflector is no longer required and CANNOT be fitted to this gearhead.
- The original drawing 340TI006 labels 1 thrust plate, 2 guard ring and 3 collar locknut. These are drawing callouts, not summary-table positions. The summary lists set of pinions 4116 640 7301 (item 1, including drive pinion 2 and output shaft 3); neither pinion nor shaft is available separately and neither has an individual order number. Item 4 is locknut M14x1.5, 4116 642 7601.
- Printed summary says the gearhead includes items 1 to 5 but stops at item 4. Item 5 is UNIDENTIFIED in the original scan; do not invent a fifth part, infer that it is optional or silently rewrite the inclusion range.
- The later SCS 01-2012 gearhead sheet lists M14 gearhead 4116 640 0106 and guard ring 4116 717 2702 rather than the TI numbers 0103 and 2700. No supersession chain or unrestricted interchange is established by this difference. The shared FS 420 / FS 420 L sheet does not extend this FS 360-only bulletin to those models or to later FS 360 generations.
- No production serial or complete machine-order number is supplied for these versions. TI 48/1994 is already reviewed introduction context, not permission to transfer its special-version serial into this change.
- Historical TI 30/1996 evidence, not current stock or verified physical interchange. No hardware operation was performed.
Source: TI 30/1996, p. 1 · TI 30/1996, p. 2 — FS 360: M14 gearhead and brush-knife versions.
Part numbers (5)
- 4116 640 0103 — M14 gearheadIncludes printed items 1–5; missing item 5 unresolved · FS 360; only the TI30/1996 configuration stated here
- 4116 640 7301 — Set of pinions; item 1Includes non-separate drive pinion and output shaft · FS 360; only the TI30/1996 configuration stated here
- 4116 642 7601 — Locknut M14x1.5; item 4Gearhead table component · FS 360; only the TI30/1996 configuration stated here
- 4116 710 3810 — 65 mm thrust plateStandard on described brush-knife versions · FS 360; only the TI30/1996 configuration stated here
- 4116 717 2700 — Hardened guard ringStandard; later IPL number differs · FS 360; only the TI30/1996 configuration stated here
Historical fitment · FS 360
FS 360: AutoCut 40-4 M14 head and replacement-top supply
M14 head and M12-supplied replacement top need the correct collar nut; changing instructions remain a source gap.
- For these M14 FS 360 versions, PolyCut 40-3 and cutting blade 255-8 may replace the standard brush knife. Original AutoCut 40-4 head 4003 710 2120 with its M12 mounting thread CANNOT be fitted as supplied. Section 2 announces head 4005 710 2100 with M14 collar nut 4005 713 6800 for gearhead 4116 640 0103. No PolyCut or blade order number is printed.
- The new AutoCut also includes a SECOND collar nut with M12 thread to mount the head on an M12-thread unit. This is conditional head conversion, not permission to force an M12 nut onto an M14 shaft or proof that every M12 machine accepts this head. All other parts are said to match the original head version.
- After introduction ONLY replacement top 4005 710 9600 is factory supplied. It arrives with NEW-TYPE M12 collar nut 4003 713 6801 so it can replace the original-head top. To use that top on head 4005 710 2100 in its M14 configuration, exchange the supplied M12 nut for M14 nut 4005 713 6800. Matching the top number alone does not establish the installed mounting thread.
- Table: complete head 4003 710 2120 becomes 4005 710 2100 and is described as including items 1–4; replacement-top assembly 4005 710 9600 includes items 1 and 3. Item 1 is the top, item 2 the original M12 nut, item 3 the new M12 nut and item 4 the M14 nut. Do not interpret that inclusion shorthand as four nuts installed together; it accompanies the alternative-nut supply and repair rules.
- Original complete head is supplied only while stocks last (remark 1); new top can also serve original heads (remark 2); original top 4003 713 9610 is no longer factory supplied after introduction (remark 3); original M12 nut 4003 713 6800 remains an older-head spare (remark 4). Modification is IN PROGRESS, not a numeric cutoff or current availability.
- SOURCE GAP: The separate AutoCut 40-4 collar-nut changing instruction sheet cited by TI30/1996 section2 was not identified in the bounded local search. Compatibility and supply rules are admitted, but no complete nut-removal/installation procedure, torque or pressing method is established. Reopen on new exact-source evidence; this is not universal absence. The later cutting-tool catalog (KT_681_02_01_11, printed page 64 / PDF page 66) lists the new top and nuts on a different complete-head number, 4005 710 2102, but supplies no changing procedure. It is not substituted for the cited instruction sheet.
- Historical TI 30/1996 evidence, not current stock or verified physical interchange. No hardware operation was performed.
Source: TI 30/1996, p. 1 · TI 30/1996, p. 2 · TI 30/1996, p. 3 — FS 360: AutoCut 40-4 M14 head and replacement-top supply.
Part numbers (7)
- 4003 710 2120 — Original AutoCut 40-4 M12 headCannot fit M14 gearhead as supplied; old stocks only · FS 360; only the TI30/1996 configuration stated here
- 4005 710 2100 — New AutoCut 40-4 headM14 fitted nut; second M12 nut supplied · FS 360; only the TI30/1996 configuration stated here
- 4005 710 9600 — Replacement top assemblySupplied with new-type M12 nut; M14 conversion conditional · FS 360; only the TI30/1996 configuration stated here
- 4005 713 6800 — M14x1.5 left-hand collar nutRequired for M14 configuration · FS 360; only the TI30/1996 configuration stated here
- 4003 713 6801 — New-type M12x1.5 left-hand collar nutSupplied in replacement top · FS 360; only the TI30/1996 configuration stated here
- 4003 713 9610 — Original topNo longer factory supplied after head introduction · FS 360; only the TI30/1996 configuration stated here
- 4003 713 6800 — Original M12x1.5 left-hand collar nutRetained for original-top repairs · FS 360; only the TI30/1996 configuration stated here
Historical fitment · FS 360
FS 360: circular-saw limit stops and 60/65 mm plate restrictions
Modified 225/250 stops suit both plate sizes; old stops require the 60 mm plate, not the 65 mm plate.
- Sections 1 and 3 permit circular saw blades 225-48, 250-50 and 225-24 with MODIFIED limit stops when using 65 mm (2.6 in.) plate 4116 710 3810. To use an ORIGINAL limit stop from existing stocks, REMOVE the 65 mm plate and REPLACE it with 60 mm (2.4 in.) plate 4116 710 3800. This is not permission to fit an old stop around the larger plate or omit the stop.
- New limit stops 225 and 250 are modified at the arrowed housing-clearance areas in figure 340TI008 and work with BOTH 60 mm and 65 mm plates. The drawing is not a dimensioned instruction to grind an old stop. New stops also come as complete initial-conversion kits with transport guard and mounting hardware. This later, expressly modified configuration does not erase TI 48/1994 restrictions for the earlier stops.
- 225 summary: kit 4116 007 1006 becomes 4116 007 1019 (item 1, includes 2–5); stop 4116 710 8200 becomes 4116 710 8201 (item 2, includes 3–4). Item 3 is washer A6.4 9291 021 0140, THREE; item 4 spline screw IS M6x14 9022 341 1270, THREE; item 5 unchanged transport guard 4119 790 3901. Nested inclusion ranges do not double the hardware quantity.
- 250 summary: kit 4116 007 1005 becomes 4116 007 1018 (item 6, includes 3, 4, 7 and 8); stop 4116 710 8205 becomes 4116 710 8206 (item 7, includes 3–4). It shares those three washers and three screws. Item 8 unchanged transport guard is 4119 790 3906, NOT the 225-kit guard.
- Remarks 1/2 apply to both kit and stop revisions: old versions last only while factory stocks remain; new versions accept both specified thrust plates. Introduction is IN PROGRESS; no serial is supplied. Current stock and complete tool-selection instructions are not established.
- The linked 2012 sheet retains stop 4116 710 8206 but shows a different transport guard, 4116 790 3901, described as 350 mm. That later entry is NOT silently substituted for either 1996 kit guard. FS 420 / FS 420 L on the shared sheet gain no compatibility claim from this FS 360 bulletin. Footer TI 09/1996, attribution and blank areas add no new fitment assertion.
- Historical TI 30/1996 evidence, not current stock or verified physical interchange. No hardware operation was performed.
Source: TI 30/1996, p. 2 · TI 30/1996, p. 4 — FS 360: circular-saw limit stops and 60/65 mm plate restrictions.
Part numbers (14)
- 4116 710 3810 — 65 mm thrust plateModified limit stop required · FS 360; only the TI30/1996 configuration stated here
- 4116 710 3800 — 60 mm thrust plateRequired to retain original limit stop · FS 360; only the TI30/1996 configuration stated here
- 4116 007 1006 — Original limit stop kit 225Old stocks; original-plate restriction · FS 360; only the TI30/1996 configuration stated here
- 4116 007 1019 — Modified limit stop kit 225Includes items 2–5 · FS 360; only the TI30/1996 configuration stated here
- 4116 710 8200 — Original limit stop 225Old stocks; 60 mm plate only · FS 360; only the TI30/1996 configuration stated here
- 4116 710 8201 — Modified limit stop 225Includes 3–4; 60 or 65 mm plate · FS 360; only the TI30/1996 configuration stated here
- 9291 021 0140 — Washer A6.4; item 3Three per kit · FS 360; only the TI30/1996 configuration stated here
- 9022 341 1270 — Spline screw IS M6x14; item 4Three per kit · FS 360; only the TI30/1996 configuration stated here
- 4119 790 3901 — Transport guard; item 5Unchanged 225-kit guard · FS 360; only the TI30/1996 configuration stated here
- 4116 007 1005 — Original limit stop kit 250Old stocks; original-plate restriction · FS 360; only the TI30/1996 configuration stated here
- 4116 007 1018 — Modified limit stop kit 250Includes 3,4,7,8 · FS 360; only the TI30/1996 configuration stated here
- 4116 710 8205 — Original limit stop 250Old stocks; 60 mm plate only · FS 360; only the TI30/1996 configuration stated here
- 4116 710 8206 — Modified limit stop 250Includes 3–4; 60 or 65 mm plate · FS 360; only the TI30/1996 configuration stated here
- 4119 790 3906 — Transport guard; item 8Unchanged 250-kit guard · FS 360; only the TI30/1996 configuration stated here
Service note · FS 550 / FS 360 / FS 420
FS 550: tool-specific handlebars and M 14x 1.5 pinion set
Complete gearhead includes housing and pinions; handle purposes remain separate.
- Handlebar 26, 4128 790 1701, is for MOWING. Handlebar 27, 4128 790 1715, is for CIRCULAR SAW BLADES. Complete control handle 28 is 4128 790 1300; throttle cable 29 is 4116 180 1104. The distinct handlebars are not an interchangeable-purpose claim.
- Complete gearhead 30, 4116 640 0104, INCLUDES gear housing 31, 4116 640 0511, and pinion set 32, 4116 640 7302. The pinion-set row explicitly prints M14x1.5; this does not supply a mounting torque. Page 2 separately establishes the left-hand mounting thread.
- Remark 1 extends handlebars 26/27 and COMPLETE gearhead 30 to predecessor FS 360/FS 420; it does not separately mark control handle 28, cable 29, gear housing 31 or pinion set 32. Keep inclusion and assembly-level applicability separate.
- Modification introduction is IN PROGRESS; no FS 550 introduction serial is printed. For component parts of assemblies not shown, the source delegates to the FS 500/550 parts list. Later IPL navigation is not proof of 1997 contents; this note does not fabricate the omitted component lists.
- Historical TI 44/1997 source guidance, not current availability, verified physical interchange or a complete repair procedure. Shared IPL sheets do not extend claims to unnamed variants. No hardware operation was performed.
Source: TI 44/1997, p. 10 — Section7 rows26–32, remark1, introduction status and component-list delegation.
Part numbers (7)
- 4128 790 1701 — Item26 mowing handlebar; remark1Exact section7 row; assembly inclusions and remark1 retained · FS 550 table context; remark1 also names FS 360 and FS 420; preserve assembly/bore restrictions
- 4128 790 1715 — Item27 circular-saw handlebar; remark1Exact section7 row; assembly inclusions and remark1 retained · FS 550 table context; remark1 also names FS 360 and FS 420; preserve assembly/bore restrictions
- 4128 790 1300 — Item28 complete control handleExact section7 row; assembly inclusions and remark1 retained · FS 550 table context; no separate predecessor remark on this row
- 4116 180 1104 — Item29 throttle cableExact section7 row; assembly inclusions and remark1 retained · FS 550 table context; no separate predecessor remark on this row
- 4116 640 0104 — Item30 complete gearhead including31/32; remark1Exact section7 row; assembly inclusions and remark1 retained · FS 550 table context; remark1 also names FS 360 and FS 420; preserve assembly/bore restrictions
- 4116 640 0511 — Item31 gear housingExact section7 row; assembly inclusions and remark1 retained · FS 550 table context; no separate predecessor remark on this row
- 4116 640 7302 — Item32 pinion set M14x1.5Exact section7 row; assembly inclusions and remark1 retained · FS 550 table context; no separate predecessor remark on this row
Wrong number or missing part for the FS 360, FS 420, FS 420 L? Report a correction →