Stihl 4116 · Section O · 11 of 12 · 29 parts
Deflector
Fits FS 360, FS 420, FS 420 L.
Historical fitment & changes (2) — includes parts and conditions not shown on this drawing.
Parts (29)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4116 710 2700 | Shield | 1 |
| 2 | 4116 641 7101 | Support | 1 |
| 3 | 9022 341 1270 | Spline screw IS-M6x14 Fitment / change note → | 3 |
| 4 | 4110 717 2801 | Guard washer | 1 |
| 5 | 4116 713 4501 | Deflector | 1 |
| 6 | 4110 716 6501 | Clamp | 1 |
| 7 | 4110 716 2900 | Strip | 1 |
| 8 | 9291 021 0140 | Washer 6.4 Fitment / change note → | 2 |
| 9 | 9022 341 1430 | Spline screw IS-M6x50 | 2 |
| 10 | 4119 716 3203 | Skirt | 1 |
| 11 | 4119 710 6000 | Blade | 1 |
| 12 | 4118 713 4105 | Blade | 1 |
| 13 | 9074 478 4125 | Pan head self-tapping screw IS-5x14 | 2 |
| 14 | 4116 710 8105 | Deflector option | 1 |
| 15 | 4119 711 2100 NLA | Plug option | 1 |
| 16 | 4116 716 6400 | Thrust pad option | 1 |
| 17 | 9222 068 0900 | Square nut M6 option | 2 |
| 18 | 4116 716 6500 | Clamp option | 1 |
| 19 | 9022 341 1420 | Spline screw IS-M6x45 option | 2 |
| 20 | 9291 021 0140 | Washer 6.4 Fitment / change note → | 2 |
| 22 | 9291 021 0140 | Washer 6.4 Fitment / change note → | 3 |
| 23 | 9022 341 1270 | Spline screw IS-M6x14 Fitment / change note → | 3 |
| 24 | 4116 710 8206 | Limit stop Ø 250 Fitment / change note → | 1 |
| 25 | 4116 790 3901 | Transport guard Ø 350 | 1 |
| 26 | 4116 792 4300 | Clamping wire | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 4116 007 1014 | Deflector kit | 1 |
| — | 4116 007 1023 | Shield assy. | 1 |
| — | 4116 007 1016 | Deflector kit | 1 |
| — | 4116 710 8101 | Deflector | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · FS 360 / FS 420
FS 360 / FS 420: special brush-knife mounting and prohibited combinations
The 65 mm thrust plate cannot be installed with the specified deflector or circular-saw limit stops.
X 30 931 757 — ONLY FS 360 special version 4116 011 2305; no FS 420 cutoff supplied.
- New FS 420 special version is for brush-knife applications; an existing FS 360 special version is updated. Both have aluminium housings. The FS 360 change is specifically version 4116 011 2305 from X 30 931 757. No FS 420 serial cutoff is printed. This differs from the clutch cutoff X 30 931 357.
- 65 mm thrust plate 4116 710 3810 replaces 60 mm 4116 710 3800 in these SPECIAL versions; hardened guard ring 4116 717 2700 replaces rider plate 4119 713 3100. Deflector 4116 710 2701 AND limit stops for circular saw blades CANNOT BE INSTALLED TOGETHER WITH THE NEW THRUST PLATE. Do not infer a saw-blade conversion from the general gearhead replacement.
- Unchanged 60 mm components: thrust plate 4116 710 3800 (key 6, includes key 7), guard washer 4116 717 2800 (key 7), thrust washer 4116 713 1600 (key 8), M12x1.5 collar nut 4119 642 7600 (key 9). Their MOQ cells are blank. New 65 mm plate 4116 710 3810 (key 10, includes key 11, MOQ 1), 65 mm washer 4116 717 2810 (key 11, MOQ 5), guard ring 4116 717 2700 (key 12, MOQ 1). ALL are excluded from the new replacement gearhead supply. MOQ 5 is not five installed washers.
- The 2012 linked gearhead IPL lists guard ring 4116 717 2702, whereas this TI specifies 4116 717 2700. The number difference is retained; no supersession or interchangeability between these rings is established here. Product version 4116 011 2305 is a MACHINE identifier, not a component to order.
- Historical TI 48/1994 guidance, not current stock or verified physical interchange. Shared IPL sheets do not extend the named source models or variants. No hardware operation was performed.
Source: TI 48/1994, p. 2 · TI 48/1994, p. 3 — special brush-knife mounting and prohibited combinations.
Part numbers (9)
- 4116 710 3800 — 60 mm thrust plate; key 6includes 7; excluded from new gearhead · FS 360 / FS 420 only in the configuration described here
- 4116 717 2800 — 60 mm guard washer; key 7excluded from new gearhead · FS 360 / FS 420 only in the configuration described here
- 4116 713 1600 — Thrust washer; key 8excluded from new gearhead · FS 360 / FS 420 only in the configuration described here
- 4119 642 7600 — M12x1.5 collar nut; key 9excluded from new gearhead · FS 360 / FS 420 only in the configuration described here
- 4116 710 3810 — 65 mm thrust plate; key 10includes 11; MOQ 1; tool restrictions · FS 360 / FS 420 only in the configuration described here
- 4116 717 2810 — 65 mm guard washer; key 11MOQ 5; excluded from new gearhead · FS 360 / FS 420 only in the configuration described here
- 4116 717 2700 — Hardened guard ring; key 12MOQ 1; distinct from later IPL number · FS 360 / FS 420 only in the configuration described here
- 4119 713 3100 — Rider platereplaced only in described special versions · FS 360 / FS 420 only in the configuration described here
- 4116 710 2701 — Deflectorprohibited with new thrust plate · FS 360 / FS 420 only in the configuration described here
Historical fitment · FS 360
FS 360: circular-saw limit stops and 60/65 mm plate restrictions
Modified 225/250 stops suit both plate sizes; old stops require the 60 mm plate, not the 65 mm plate.
- Sections 1 and 3 permit circular saw blades 225-48, 250-50 and 225-24 with MODIFIED limit stops when using 65 mm (2.6 in.) plate 4116 710 3810. To use an ORIGINAL limit stop from existing stocks, REMOVE the 65 mm plate and REPLACE it with 60 mm (2.4 in.) plate 4116 710 3800. This is not permission to fit an old stop around the larger plate or omit the stop.
- New limit stops 225 and 250 are modified at the arrowed housing-clearance areas in figure 340TI008 and work with BOTH 60 mm and 65 mm plates. The drawing is not a dimensioned instruction to grind an old stop. New stops also come as complete initial-conversion kits with transport guard and mounting hardware. This later, expressly modified configuration does not erase TI 48/1994 restrictions for the earlier stops.
- 225 summary: kit 4116 007 1006 becomes 4116 007 1019 (item 1, includes 2–5); stop 4116 710 8200 becomes 4116 710 8201 (item 2, includes 3–4). Item 3 is washer A6.4 9291 021 0140, THREE; item 4 spline screw IS M6x14 9022 341 1270, THREE; item 5 unchanged transport guard 4119 790 3901. Nested inclusion ranges do not double the hardware quantity.
- 250 summary: kit 4116 007 1005 becomes 4116 007 1018 (item 6, includes 3, 4, 7 and 8); stop 4116 710 8205 becomes 4116 710 8206 (item 7, includes 3–4). It shares those three washers and three screws. Item 8 unchanged transport guard is 4119 790 3906, NOT the 225-kit guard.
- Remarks 1/2 apply to both kit and stop revisions: old versions last only while factory stocks remain; new versions accept both specified thrust plates. Introduction is IN PROGRESS; no serial is supplied. Current stock and complete tool-selection instructions are not established.
- The linked 2012 sheet retains stop 4116 710 8206 but shows a different transport guard, 4116 790 3901, described as 350 mm. That later entry is NOT silently substituted for either 1996 kit guard. FS 420 / FS 420 L on the shared sheet gain no compatibility claim from this FS 360 bulletin. Footer TI 09/1996, attribution and blank areas add no new fitment assertion.
- Historical TI 30/1996 evidence, not current stock or verified physical interchange. No hardware operation was performed.
Source: TI 30/1996, p. 2 · TI 30/1996, p. 4 — FS 360: circular-saw limit stops and 60/65 mm plate restrictions.
Part numbers (14)
- 4116 710 3810 — 65 mm thrust plateModified limit stop required · FS 360; only the TI30/1996 configuration stated here
- 4116 710 3800 — 60 mm thrust plateRequired to retain original limit stop · FS 360; only the TI30/1996 configuration stated here
- 4116 007 1006 — Original limit stop kit 225Old stocks; original-plate restriction · FS 360; only the TI30/1996 configuration stated here
- 4116 007 1019 — Modified limit stop kit 225Includes items 2–5 · FS 360; only the TI30/1996 configuration stated here
- 4116 710 8200 — Original limit stop 225Old stocks; 60 mm plate only · FS 360; only the TI30/1996 configuration stated here
- 4116 710 8201 — Modified limit stop 225Includes 3–4; 60 or 65 mm plate · FS 360; only the TI30/1996 configuration stated here
- 9291 021 0140 — Washer A6.4; item 3Three per kit · FS 360; only the TI30/1996 configuration stated here
- 9022 341 1270 — Spline screw IS M6x14; item 4Three per kit · FS 360; only the TI30/1996 configuration stated here
- 4119 790 3901 — Transport guard; item 5Unchanged 225-kit guard · FS 360; only the TI30/1996 configuration stated here
- 4116 007 1005 — Original limit stop kit 250Old stocks; original-plate restriction · FS 360; only the TI30/1996 configuration stated here
- 4116 007 1018 — Modified limit stop kit 250Includes 3,4,7,8 · FS 360; only the TI30/1996 configuration stated here
- 4116 710 8205 — Original limit stop 250Old stocks; 60 mm plate only · FS 360; only the TI30/1996 configuration stated here
- 4116 710 8206 — Modified limit stop 250Includes 3–4; 60 or 65 mm plate · FS 360; only the TI30/1996 configuration stated here
- 4119 790 3906 — Transport guard; item 8Unchanged 250-kit guard · FS 360; only the TI30/1996 configuration stated here
Wrong number or missing part for the FS 360, FS 420, FS 420 L? Report a correction →