Stihl 4116 · Section K · 10 of 16 · 37 parts
Handlebar, Control handle
Fits FS 500, FS 550, FS 550 L.
Historical fitment & changes (3) — includes parts and conditions not shown on this drawing.
Parts (37)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4128 790 1701 | Handlebar Fitment / change note → | 1 |
| 2 | 4128 790 1715 | Handlebar Fitment / change note → | 1 |
| 3 | 4128 791 0300 | Handle, left | 1 |
| 4 | 4128 791 2710 | Tube | 1 |
| 5 | 4116 791 0600 | Clamp, top | 1 |
| 6 | 4116 791 0615 | Clamp, base | 1 |
| 7 | 9022 371 0710 | Spline screw IS-M4x20 | 4 |
| 8 | 4116 791 0610 | Clamp, top | 1 |
| 9 | 4116 791 0605 | Clamp, base | 1 |
| 10 | 9022 341 1010 | Spline screw IS-M5x18 | 2 |
| 11 | 9308 021 0180 | Washer 8.4 | 1 |
| 12 | 4119 791 6100 | Hexagon head screw M8x70 | 1 |
| 13 | 4128 790 0304 | Handle, right | 1 |
| 14 | 9074 478 3025 | Pan head self-tapping screw IS-P4x16 | 3 |
| 15 | 4128 182 1700 | Slide control | 1 |
| 16 | 4128 182 4201 | Detent spring | 1 |
| 17 | 4128 182 6200 | Collar screw | 1 |
| 18 | 4128 182 4502 | Torsion spring | 1 |
| 19 | 4128 182 4501 | Torsion spring | 1 |
| 20 | 4128 182 1000 | Throttle trigger | 1 |
| 21 | 4128 182 4504 | Torsion spring | 1 |
| 22 | 4128 182 4500 | Torsion spring | 1 |
| 23 | 4128 182 0800 | Lockout lever | 1 |
| 24 | 4128 793 3000 | Slide | 1 |
| 25 | 4128 791 3100 | Spring | 1 |
| 26 | 9214 320 0700 | Lock nut M5 | 1 |
| 27 | 9022 346 1070 | Spline screw IS-M5x30 | 1 |
| 28 | 9291 021 0120 | Washer 5.3 | 1 |
| 29 | 4116 180 1106 | Throttle cable | 1 |
| 30 | 4116 182 3200 | Throttle cable | 1 |
| 31 | 4116 180 7202 | Guide piece | 1 |
| 32 | 9074 478 3025 | Pan head self-tapping screw IS-P4x16 | 2 |
| 33 | 4116 431 2105 | Double connector tag | 1 |
| 34 | 4116 431 2100 | Connector tag | 1 |
| 35 | 9074 478 4425 | Pan head self-tapping screw IS-P6x19 | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 4128 790 1309 | Control handle | 1 |
| — | 4116 790 1351 | Control handle | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · FS 550
FS 550: mowing and circular-saw handle configurations
Series 4116 introduction describes differences from FS 360/420, not wholesale parts interchange.
- The cover identifies FS 550, series 4116, as the largest model in the contemporary high-performance clearing-saw line. Recommended applications are the same as FS 360 and FS 420. The chapters describe DIFFERENCES over those predecessors, not a complete specification or universal retrofit list.
- The supplied bike handle is designed for circular saw blades; a special bike handle is available for mowing. Both configurations are pictured separately. The multifunction control handle has a soft, non-slip grip surface. No handle dimension or conversion procedure is inferred from the photographs.
- The improved FOUR-POINT antivibration system is claimed to reduce vibration by 20%. This is a historical source claim, not a measured result for an individual machine; no vibration exposure value is supplied.
- The new comfortable FULL HARNESS is OPTIONAL, with its front/rear illustration and description delegated to retained TI22/1997. That accessory bulletin already has separate reviewed design/care and spare-parts notes; optional does not mean included with every FS 550. No new harness part-number equivalence is inferred from the drawing.
- Historical TI44/1997 guidance for the named FS 550 configuration only. Shared IPL sheets do not extend these claims to FS 500, FS 550 L, FS 360 or FS 420. Not current stock, verified physical interchange or a complete operating procedure. No hardware operation was performed.
Source: TI 44/1997, p. 1 · TI 44/1997, p. 2 — Cover, contents and section 1: scope, handles, four-point AV and optional harness.
Referenced bulletin evidence: TI 22/1997, p. 1 · TI 22/1997, p. 2 — Full harness 4134 710 9000: design, release and care.
No additional parts-table entry added.
Service note · FS 550
FS 550: clamp-style throttle adjustment and leak-test pressures
Engine pressure/vacuum is±0.5 bar; carburetor inlet needle is tested at 0.8 bar.
- In 398TI 004 KN, screw(1) secures cover(2) and its cable clamp. Slacken screw about TWO OR THREE TURNS until the cover releases the clamp. Hold the throttle trigger fully squeezed, retighten the screw to secure the clamp, THEN release the trigger. This is the printed full-throttle adjustment, not a later throttle-cable design or an engine-running instruction.
- Engine leak test: PRESSURE +7.25 psi(+0.5 bar); VACUUM -7.25 psi(-0.5 bar). Carburetor INLET NEEDLE testing pressure: 11.6 psi(0.8 bar). No dwell time, allowed pressure drop, isolation setup or needle leakage threshold is supplied here. Do not turn these three values into a complete test or use the carburetor pressure for the crankcase.
- If started during repairs/maintenance, the source requires observing local/national safety regulations and owner-manual precautions. It delegates repairs to a service manual; servicing the carburetor, troubleshooting and standard procedures are described in SEPARATE HANDBOOKS, not that manual. The owner manual and these separate handbooks have not been reviewed as complete procedures in this note.
- Historical TI 44/1997 source guidance, not current availability, verified physical interchange or a complete repair procedure. Shared IPL sheets do not extend claims to unnamed variants. No hardware operation was performed.
Source: TI 44/1997, p. 8 — Section6 repairs context, complete6.1.1 adjustment/398TI004 KN and6.2 leakage-test data.
No additional parts-table entry added.
Service note · FS 550 / FS 360 / FS 420
FS 550: tool-specific handlebars and M 14x 1.5 pinion set
Complete gearhead includes housing and pinions; handle purposes remain separate.
- Handlebar 26, 4128 790 1701, is for MOWING. Handlebar 27, 4128 790 1715, is for CIRCULAR SAW BLADES. Complete control handle 28 is 4128 790 1300; throttle cable 29 is 4116 180 1104. The distinct handlebars are not an interchangeable-purpose claim.
- Complete gearhead 30, 4116 640 0104, INCLUDES gear housing 31, 4116 640 0511, and pinion set 32, 4116 640 7302. The pinion-set row explicitly prints M14x1.5; this does not supply a mounting torque. Page 2 separately establishes the left-hand mounting thread.
- Remark 1 extends handlebars 26/27 and COMPLETE gearhead 30 to predecessor FS 360/FS 420; it does not separately mark control handle 28, cable 29, gear housing 31 or pinion set 32. Keep inclusion and assembly-level applicability separate.
- Modification introduction is IN PROGRESS; no FS 550 introduction serial is printed. For component parts of assemblies not shown, the source delegates to the FS 500/550 parts list. Later IPL navigation is not proof of 1997 contents; this note does not fabricate the omitted component lists.
- Historical TI 44/1997 source guidance, not current availability, verified physical interchange or a complete repair procedure. Shared IPL sheets do not extend claims to unnamed variants. No hardware operation was performed.
Source: TI 44/1997, p. 10 — Section7 rows26–32, remark1, introduction status and component-list delegation.
Part numbers (7)
- 4128 790 1701 — Item26 mowing handlebar; remark1Exact section7 row; assembly inclusions and remark1 retained · FS 550 table context; remark1 also names FS 360 and FS 420; preserve assembly/bore restrictions
- 4128 790 1715 — Item27 circular-saw handlebar; remark1Exact section7 row; assembly inclusions and remark1 retained · FS 550 table context; remark1 also names FS 360 and FS 420; preserve assembly/bore restrictions
- 4128 790 1300 — Item28 complete control handleExact section7 row; assembly inclusions and remark1 retained · FS 550 table context; no separate predecessor remark on this row
- 4116 180 1104 — Item29 throttle cableExact section7 row; assembly inclusions and remark1 retained · FS 550 table context; no separate predecessor remark on this row
- 4116 640 0104 — Item30 complete gearhead including31/32; remark1Exact section7 row; assembly inclusions and remark1 retained · FS 550 table context; remark1 also names FS 360 and FS 420; preserve assembly/bore restrictions
- 4116 640 0511 — Item31 gear housingExact section7 row; assembly inclusions and remark1 retained · FS 550 table context; no separate predecessor remark on this row
- 4116 640 7302 — Item32 pinion set M14x1.5Exact section7 row; assembly inclusions and remark1 retained · FS 550 table context; no separate predecessor remark on this row
Wrong number or missing part for the FS 500, FS 550, FS 550 L? Report a correction →