← Brushcutters & other equipment · series 4119

Stihl 4119 · Section H · 8 of 17 · 24 parts

Clutch housing, Drive tube assembly

Fits FS 220, FS 220 K, FS 280, FS 280 K, FS 290.

Parts diagrams →

Historical fitment & changes (3) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
110101011121314151617181922021222334056789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (24)

PosPart numberDescriptionQty
1 4119 161 0501 Clutch housing 1
2 9503 003 6650 Grooved ball bearing 6203-2RS 1
3 9456 621 4330 Circlip 40x1.75 1
5 9455 621 1800 Circlip 17x1 1
6 4119 791 9300 Rubber insert 1
7 4119 791 7200 Sleeve 1
8 4119 792 6900 Washer 1
9 4119 162 2800 Cap 1
10 9022 371 1020 Spline screw IS-M5x20 → replaced by 9022 371 1050 TI 30/2004 10
11 9307 021 0100 Washer 4.3 1
12 9022 313 0680 Spline screw IS-M4x16 1
13 4119 710 7104 Drive tube assembly Ø 28 mm / 1 1/8'' x 1.55 m / 61" 1
14 4119 710 7114 Drive tube assembly Ø 28 mm / 1 1/8'' x 1.42 m / 55 15/16" 1
15 4119 710 7100 Drive tube assembly Ø 28 mm / 1 1/8'' x 1.55 m / 61" 1
16 4119 710 7110 Drive tube assembly Ø 28 mm / 1 1/8'' x 1.42 m / 55 15/16" 1
17 4119 711 7301 Flexible liner Fitment / change note → 1
18 0000 967 3725 Warning pictogram FS 1
19 4119 711 7300 Flexible liner Fitment / change note → 1
20 0000 967 3684 Warning pictogram FS 1
21 4119 711 3201 Drive shaft 1
22 4119 711 3210 Drive shaft 1
23 4119 791 9400 Cable clamp 1
40 4119 711 2100 NLA Plug 1
Not numbered on the diagram — assemblies, kits and options
— 0781 120 1110 Gear lubricant 225 g not illustratedoption 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · FS 160 / FS 180 / FS 220 / FS 280

FS 160 / 180 / 220 / 280: new clutch and smaller drum must stay paired

Unlined clutch shoes require the new drum; replacement assembly includes both.

X 28 469 096 — Printed introduction for this component only; not a universal machine cutoff or interchange guarantee.

  • From X 28 469 096, clutch 4119 160 2001 has shoes WITHOUT linings and is paired with a new drum of smaller inside diameter. Original and new versions CANNOT be combined. New clutch-with-drum assembly 4119 160 2050 includes items 1–3; clutch item 1 includes unchanged spring 0000 997 6205 (item 2). No drum bore dimension is printed.
  • Original drum 4119 160 2905 is no longer factory-available, so use the complete new assembly to replace it. The new drum (item 3, printed -*- rather than an order number) is NOT separately available up to the end of 1998. No later separate-drum number is supplied here.
  • Original clutch 4119 160 2000 remains available for older machines up to END OF 1998; after that date the new clutch AND new drum must be used. This is a historical supply timeline, not current stock evidence. All other parts remain as before. Cover scope does not silently include FS 290, FR 220 or K variants sharing an IPL sheet.
  • Historical TI 15/1994 guidance for the explicitly named models only; no successor or unlisted variant applicability inferred. Factory supply statements are historical, not current stock claims. MOQ columns are order quantities, not fitting quantities. No physical interchange test was performed.

Source: TI 15/1994, p. 1 — FS 160 / 180 / 220 / 280: new clutch and smaller drum must stay paired.

Part numbers (5)
  • 4119 160 2000 — Original lined clutchhistorically available through end of 1998 · FS 160 / 180 / 220 / 280: new clutch and smaller drum must stay paired
  • 4119 160 2001 — New unlined clutch, item 1requires matching new drum · FS 160 / 180 / 220 / 280: new clutch and smaller drum must stay paired
  • 4119 160 2050 — Clutch with drum, items 1–3complete replacement assembly · FS 160 / 180 / 220 / 280: new clutch and smaller drum must stay paired
  • 0000 997 6205 — Clutch spring, item 2unchanged; included in clutch · FS 160 / 180 / 220 / 280: new clutch and smaller drum must stay paired
  • 4119 160 2905 — Original clutch drum, item 3no longer factory-available · FS 160 / 180 / 220 / 280: new clutch and smaller drum must stay paired

Service note · FS 220 / FS 280

FS 220 / FS 280: flexible liner replaces six rubber-mounted bushes

Standard drive tube retains 4119 710 7102 and takes liner 4119 711 7301.

  • Flexible polymer liner supports the drive shaft instead of SIX rubber-mounted bushes and is replaceable when worn. Original and new COMPLETE drive tubes are fully interchangeable; this does not establish interchange of individual old bush supports and liner in an unmodified tube.
  • Looking FROM THE GEAR HEAD END, the flexible-liner fins must point LEFT / COUNTERCLOCKWISE so the liner cannot rotate with the drive shaft. Push the liner in from that gear-head end until it is flush with the OTHER, powerhead end of the tube. Coat the DRIVE SHAFT with STIHL multipurpose grease 0781 120 1109 before inserting it. Diagram identifies drive tube (1), liner (2) and fin arrows; no numeric grease quantity is stated.
  • Standard FS 220 / FS 280 complete tube 4119 710 7102 keeps its number and includes liner 4119 711 7301. ONLY the modified standard tube is factory-available. Introduction in progress with no serial. Do not substitute the K-version liner 4119 711 7300 or infer FS 290 applicability from the shared IPL sheet.
  • Historical TI 15/1994 guidance for the explicitly named models only; no successor or unlisted variant applicability inferred. Factory supply statements are historical, not current stock claims. MOQ columns are order quantities, not fitting quantities. No physical interchange test was performed.

Source: TI 15/1994, p. 2 — FS 220 / FS 280: flexible liner replaces six rubber-mounted bushes.

Part numbers (3)
  • 4119 710 7102 — FS 220 / FS 280 complete drive tubeunchanged number; modified version only · FS 220 / FS 280: flexible liner replaces six rubber-mounted bushes
  • 4119 711 7301 — Flexible liner for standard tubenew replaceable liner · FS 220 / FS 280: flexible liner replaces six rubber-mounted bushes
  • 0781 120 1109 — STIHL multipurpose greasecoat drive shaft before insertion · FS 220 / FS 280: flexible liner replaces six rubber-mounted bushes

Service note · FS 220 K / FS 280 K

FS 220 K / FS 280 K: separate liner and stock rule for K drive tubes

K drive tube remains 4119 710 7112 and takes liner 4119 711 7300.

  • The table explicitly lists FS 220 K and FS 280 K: complete tube 4119 710 7112 retains its number and includes new flexible liner 4119 711 7300. Unlike the standard tube, the UNMODIFIED K tube remains factory-supplied only while stocks last. Introduction in progress, no serial.
  • The section replaces six rubber-mounted bushes with a replaceable polymer liner and states original/new COMPLETE tubes are fully interchangeable; no cross-swap between standard and K tube/liner pairs is stated.
  • Looking FROM THE GEAR HEAD END, the flexible-liner fins must point LEFT / COUNTERCLOCKWISE so the liner cannot rotate with the drive shaft. Push the liner in from that gear-head end until it is flush with the OTHER, powerhead end of the tube. Coat the DRIVE SHAFT with STIHL multipurpose grease 0781 120 1109 before inserting it. Diagram identifies drive tube (1), liner (2) and fin arrows; no numeric grease quantity is stated.
  • Keep standard liner 4119 711 7301 distinct from K liner 4119 711 7300. A shared FS 290 IPL sheet is not source evidence of FS 290 fitment.
  • Historical TI 15/1994 guidance for the explicitly named models only; no successor or unlisted variant applicability inferred. Factory supply statements are historical, not current stock claims. MOQ columns are order quantities, not fitting quantities. No physical interchange test was performed.

Source: TI 15/1994, p. 2 — FS 220 K / FS 280 K: separate liner and stock rule for K drive tubes.

Part numbers (3)
  • 4119 710 7112 — FS 220 K / FS 280 K complete drive tubeunchanged number; old version while stocks last · FS 220 K / FS 280 K: separate liner and stock rule for K drive tubes
  • 4119 711 7300 — Flexible liner for K tubenew replaceable liner · FS 220 K / FS 280 K: separate liner and stock rule for K drive tubes
  • 0781 120 1109 — STIHL multipurpose greasecoat drive shaft before insertion · FS 220 K / FS 280 K: separate liner and stock rule for K drive tubes

Wrong number or missing part for the FS 220, FS 220 K, FS 280, FS 280 K, FS 290? Report a correction →