Stihl 4128 · Section A · 1 of 21 · 27 parts
Crankcase, Cylinder
Fits FS 400, FS 450, FS 480.
Historical fitment & changes (2) — includes parts and conditions not shown on this drawing.
This drawing carries 3 bore sizes — Ø 40 mm , Ø 42 mm , Ø 44 mm . Not interchangeable — measure your cylinder before ordering. The catalogue lists them on one sheet for one machine and never says which variant each belongs to, so this guide does not either.
Parts (27)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4128 020 2600 | Crankcase, fan side | 1 |
| 2 | 0000 988 8600 | Sleeve | 4 |
| 3 | 9503 003 0242 | Grooved ball bearing 6201 | 2 |
| 4 | 4128 020 2900 | Crankcase | 1 |
| 5 | 9640 003 1195 | Oil seal 12x22x5 | 2 |
| 6 | 4128 030 0400 | Crankshaft | 1 |
| 7 | 9075 478 4175 | Pan head self-tapping screw IS-D5x28 | 8 |
| 8 | 9512 003 2250 | Needle cage 10x13x12.5 | 1 |
| 9 | 9512 003 2251 | Needle cage 10x13x12.5 | 1 |
| 10 | 4128 029 2300 | Cylinder gasket | 1 |
| 11 | 4128 020 1201 | Cylinder with piston Ø 40 mm | 1 |
| 12 | 4128 020 1211 | Cylinder with piston Ø 42 mm | 1 |
| 13 | 4128 020 1202 | Cylinder with piston Ø 44 mm | 1 |
| 14 | 1123 030 2019 | Piston Ø 40 mm | 1 |
| 15 | 4128 030 2005 | Piston Ø 42 mm | 1 |
| 16 | 4128 030 2002 | Piston Ø 44 mm | 1 |
| 17 | 1123 034 3005 | Piston ring Ø 40x1.2 mm | 2 |
| 18 | 1123 034 3003 | Piston ring Ø 42x1.2 mm | 2 |
| 19 | 1133 034 3000 | Piston ring Ø 44x1.2 mm | 2 |
| 20 | 4119 034 1500 | Piston pin 10x6.5x28 | 1 |
| 21 | 4128 034 1500 | Piston pin 10x6.5x28 | 1 |
| 22 | 9463 650 1000 | Snap ring 10 | 2 |
| 23 | 1110 400 7005 | Spark plug Bosch WSR 6 F | 1 |
| 24 | 4128 020 9400 | Decompression valve | 1 |
| 25 | 4128 149 0600 | Muffler gasket | 1 |
| 26 | 0783 830 2000 | Tube of sealant Dirko HT red option | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 4128 007 1050 | Set of gaskets | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · FS 120 / FS 200 / FS 350 / FS 400 / FS 450
FS120/200/350/400/450: four-port engine specifications
FS200 and FS350 share the printed column; all strokes are32 mm.
- New single-cylinder two-stroke engine uses FOUR-PORT technology. Better mixture control, clean combustion and lower emissions are source claims without measured values here. Decompression valve is specified ONLY FOR FS350/400/450, not FS120/200.
- Engine table: FS120 =30.8 cc (1.88 ci),35 mm (1.37 in) bore,1.3 kW (1.8 bhp). SHARED FS200/FS350 column =36.3 cc (2.21 ci),38 mm (1.49 in) bore,1.6 kW (2.2 bhp). FS400 =40.2 cc (2.45 ci),40 mm (1.57 in),1.9 kW (2.6 bhp). FS450 =44.3 cc (2.70 ci),42 mm (1.65 in),2.1 kW (2.8 bhp). Power is to ISO8893.
- ALL four columns specify32 mm (1.26 in) stroke. Rewind starter is SINGLE PAWL with ElastoStart grip. Easy-start description also specifies manual fuel primer and the model-limited decompression valve. Starter-rope entry delegates to section4; the reviewed ElastoStart note resolves it as grip-with-rope0000 190 3400 and separate rope0000 195 8200, without inferred dimensions.
- These are1997 engine specifications; shared catalog sheets also naming FS250/300/480 do not extend these values to those models.
- Historical TI42/1997 configurations only, not all later versions sharing a model name. No hardware operation was performed. No part interchange or numeric serial cutoff is established.
Source: TI 42/1997, p. 2 · TI 42/1997, p. 3 · TI 42/1997, p. 6 — Section1 powerhead/cylinder/easy-start; section2.1.1 complete engine table; section4 starter-rope cross-reference.
No additional parts-table entry added.
Service note · FS 300 / FS 350 / FS 400 / FS 450
FS 300 / 350 / 400 / 450: early crankshaft puller hole modification
Puller 4119 890 4600 can replace service tool ZS on the clutch side; early tools may require the illustrated holes.
- Section 3.2 identifies puller 4119 890 4600 as an alternative to “service tool ZS” for removing the crankshaft from the CLUTCH SIDE of the crankcase. This is a service-tool application within the bulletin’s FS 300/350/400/450 scope, not an installed machine part or a claim for every ZS application.
- EARLY VERSIONS may lack the two holes required for this job. In that case the bulletin instructs modifying the TOOL as shown: drill a NEW 6 mm diameter hole (1); open up the EXISTING 6 mm diameter hole (2) to make a SLOT shown by a broken line. It is not a direction to drill the crankcase or make both holes into slots.
- Figure 255TI005 KN labels the central threaded hole M10. Hole (1) is on its left at the printed horizontal dimension 45; hole (2) is on its right at 47. The slot direction at (2) is shown with a 51° angle to the depicted downward vertical reference. The original drawing is the controlling geometry; the numbers 45 and 47 have no unit suffix in the sketch and are retained as printed rather than a manufactured drilling template.
- The central M10 label is not the diameter of the two 6 mm holes. Do not infer an M10 thread pitch, drill depth, slot length or fabrication tolerance: none is specified here. The retained text OCR’s stray “fo” near 47 is not a separate dimension. All other holes in the outline are drawing context, not additional modification instructions.
- The exact-model crankcase sheets are navigation only; the tool has no invented IPL row or part position. The complete crankshaft-removal procedure and physical tool suitability are not established by this modification note. Shared FS 480 catalog context does not extend the named model scope.
- Historical source guidance; no present-day stock guarantee or verified physical interchange. No hardware operation was performed.
Source: TI 20/1998, p. 1 · TI 20/1998, p. 4 — Page 4 section 3.2 and complete dimensioned drawing255TI005 KN; page 1 exact model scope.
Part numbers (1)
- 4119 890 4600 — Crankshaft pullerService tool; early-tool hole modification · Clutch-side crankshaft removal for the named FS models
Wrong number or missing part for the FS 400, FS 450, FS 480? Report a correction →