Stihl 4128 · Section D · 4 of 21 · 28 parts
Ignition system, Clutch
Fits FS 400, FS 450, FS 480.
Historical fitment & changes (3) — includes parts and conditions not shown on this drawing.
Parts (28)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4128 400 1200 | Flywheel Fitment / change note → | 1 |
| 2 | 9220 260 1100 | Hexagon nut M8 | 1 |
| 3 | 4128 400 1306 | Ignition module Fitment / change note → | 1 |
| 4 | not sold separately | Ignition lead 305 mm not available as a separate item | 1 |
| 5 | 0000 989 1010 | Grommet | 1 |
| 6 | 4128 440 1101 | Short circuit wire | 1 |
| 7 | 4128 440 1105 | Short circuit wire | 1 |
| 8 | 0000 989 0804 | Grommet | 2 |
| 9 | 4128 448 1202 | Lead retainer | 1 |
| 10 | 9075 478 4159 | Pan head self-tapping screw IS-D5x24 | 2 |
| 11 | 4128 448 1200 | Lead retainer | 1 |
| 12 | 0000 998 0604 | Torsion spring | 1 |
| 13 | 4128 405 1000 | Spark plug boot | 1 |
| 14 | 4128 160 2001 | Clutch | 1 |
| 15 | not sold separately | Clutch shoe not available as a separate item | 2 |
| 16 | 0000 961 0608 | Ring | 2 |
| 17 | 0000 997 5519 | Tension spring | 2 |
| 18 | 4128 162 1000 | Cover washer | 1 |
| 19 | 0000 951 0606 | Hexagon head screw | 2 |
| 20 | 0000 958 1000 | Washer 16x10x0.5 | 2 |
| 21 | 4128 160 2900 | Clutch drum | 1 |
| 22 | 9456 621 3860 | Circlip 35x1.5 | 1 |
| 23 | 9503 003 7450 | Grooved ball bearing 6202-2RS | 1 |
| 24 | 9455 621 1520 | Circlip 15x1 | 1 |
| 25 | 9075 478 4159 | Pan head self-tapping screw IS-D5x24 | 4 |
| 26 | 4128 160 0601 | Clutch housing | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 0000 405 0600 NLA | Ignition lead 1 m not illustratedoption | 1 |
| — | 0000 930 2251 | Ignition lead 10 m not illustratedoption | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Historical fitment · FS 400 / FS 450 / FR 450
FS 400 / FS 450 / FR 450: series 4128 replacement ignition assignment
4128 400 1306 with flywheel 4128 400 1200; 305 mm ignition lead.
- Printed series 4128. Use 4128 400 1306 with flywheel 4128 400 1200.
- Printed ignition-lead length: 305 mm (12 in). Preserve both printed units.
- TI01/1999 lists replacement combinations for the then-current machines, not every earlier configuration. Older machines are referred to Spare Parts for Previous Models in their own illustrated parts lists; no serial cutoff is supplied here.
- Use only the listed ignition-module/flywheel combinations. The source warns that incorrect combinations can cause excessive RPM or running in reverse; sharing a module number does not make all flywheels interchangeable.
- Universal replacement modules may differ from production modules in maker, shape and part number. The source describes installation/function compatibility within its assignments, not universal compatibility or a project hardware test.
- Some replacement modules require shortening the ignition lead and/or short-circuit wire and crimping a different short-circuit connector. The table gives ignition-lead lengths only; it supplies neither a short-circuit-wire length nor a connector part number. Do not infer that every row needs modification.
- Only the named models and printed series are covered. A shared IPL sheet does not extend this assignment to unnamed models or modern MS equivalents. This 1999 USA bulletin is historical guidance, not current availability.
- The source explicitly names FR 450, but no exact-model ignition sheet is retained here. The note is linked only to the other named models; no similar model sheet is substituted.
Source: TI 1/1999, p. 1 · TI 1/1999, p. 3 — 1.1 general restrictions and 1.2.2 power-tool assignments.
Part numbers (2)
- 4128 400 1306 — Replacement ignition moduleAssigned component · FS 400 / FS 450 / FR 450, printed series 4128, listed combination only
- 4128 400 1200 — Assigned flywheelRequired pairing · FS 400 / FS 450 / FR 450, printed series 4128
Service note · FS 120 / FS 200 / FS 350 / FS 400 / FS 450
FS120/200/350/400/450: clutch and rigid-shaft construction
Two unlined clutch shoes;4,300 rpm engagement is not idle or cut-off speed.
- Clutch uses TWO LARGE-DIAMETER SHOES WITHOUT LININGS. The rigid drive shaft is supported in a FULL-LENGTH LINER. Neither description supplies part numbers, wear limits, lubrication intervals or a shaft conversion.
- Every engine-table column gives clutch engagement at4,300 rpm. Do not confuse that value with2,800 rpm idle, electronic cut-off without a cutting tool, or the rated output-shaft speed. No field clutch test was performed.
- Historical TI42/1997 configurations only, not all later versions sharing a model name. No hardware operation was performed. No part interchange or numeric serial cutoff is established.
Source: TI 42/1997, p. 3 — Section1 clutch/shaft; section2.1.1 clutch row.
No additional parts-table entry added.
Service note · FS 120 / FS 200 / FS 350 / FS 400 / FS 450
FS120/200/350/400/450: ignition, plugs and fuel capacities
305 mm ignition lead applies only to FS400/450.
- Ignition module has INTEGRAL ELECTRONIC SPEED LIMITER. Suppressed spark plugs listed are Bosch WSR6F, NGK BPMR7A OR Champion RCJ6Y; these are alternatives, not a requirement to combine them. No plug gap, torque or ignition timing is specified here.
- Ignition lead length305 mm (12 in) is explicitly FS400/450 ONLY. It is not an ignition-module part number or a length requirement for FS120/200/350.
- Transparent tank enables fuel-level identification. Capacity FS120/200/350 =0.64 l (1.35 US pt); FS400/450 =0.68 l (1.43 US pt). No fuel mixture specification or tank interchange is established on these pages.
- Historical TI42/1997 configurations only, not all later versions sharing a model name. No hardware operation was performed. No part interchange or numeric serial cutoff is established.
Source: TI 42/1997, p. 3 · TI 42/1997, p. 4 — Section1 fuel-system description; sections2.1.2 tank capacity and2.1.3 ignition.
No additional parts-table entry added.
Wrong number or missing part for the FS 400, FS 450, FS 480? Report a correction →