← FS 400, FS 450, FS 480

Stihl 4128 · Section O · 14 of 21 · 35 parts

Handlebar, Control handle

Fits FS 400, FS 450, FS 480.

Parts diagrams →

Historical fitment & changes (1) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
110111213141415161718192202122242526272829330313233456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (35)

PosPart numberDescriptionQty
1 4128 790 1701 Handlebar 1
2 4128 790 1715 Handlebar 1
3 4128 791 0300 Handle, left 1
4 4128 791 2710 Tube 1
5 4116 791 0600 Clamp, top 1
6 4116 791 0615 Clamp, base 1
7 9022 371 0710 Spline screw IS-M4x20 4
8 4128 791 0900 Clamp, top 1
9 0000 997 1304 Compression spring Fitment / change note → 1
10 4128 791 0905 Clamp, base 1
11 4128 790 7501 Tommy screw 1
12 9291 021 0140 Washer 6.4 1
13 0000 997 1701 Compression spring 1
14 4128 790 0300 Handle, right 1
15 4128 182 4501 Torsion spring 1
16 4128 182 0800 Lockout lever 1
17 4128 182 1700 Slide control 1
18 4128 182 4200 Detent spring 1
19 4128 442 1605 Contact spring 1
20 4128 182 6200 Collar screw 1
21 4128 442 1600 Contact spring 1
22 4128 182 4500 Torsion spring 1
24 9074 478 3025 Pan head self-tapping screw IS-P4x16 3
25 9214 320 0700 Lock nut M5 1
26 9291 021 0120 Washer 5.3 1
27 9022 346 1070 Spline screw IS-M5x30 1
28 4128 180 1102 Throttle cable 1
29 not sold separately Hose 690 mm / 27 3/16'' not available as a separate item 1
30 4134 182 2105 NLA Support, bottom 1
31 4134 180 6701 NLA Support → replaced by 4134 180 6702 TI 5/2003 1
32 9075 478 4159 Pan head self-tapping screw IS-D5x24 1
33 0000 951 1100 Screw IS-D5x20 1
Not numbered on the diagram — assemblies, kits and options
— 4128 790 1300 Control handle 1
— 4203 711 7201 Hose 960 mm / 37 13/16'' not illustratedoption 1
— 4134 180 6700 NLA Support 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Historical fitment · FS 300 / FS 350 / FS 400 / FS 450

FS 300 / 350 / 400 / 450: handlebar clamp spring change

Spring 1304 replaces 1302 between the two clamp moldings; introduction remains in progress.

  • Section 2 and figure 255TI003 KN locate the helical spring BETWEEN THE TWO MOLDINGS of the handlebar clamp. Original 0000 997 1302 will be replaced by 0000 997 1304. Figure item 1 is this spring, not the separate spring associated with the tommy screw.
  • Introduction is IN PROGRESS, with no serial or date boundary. The original spring remains available FOR OTHER MODELS (remark 1). No other models are named and no blanket spring interchange, new clamp molding or combined conversion kit is specified.
  • Later FS 300/350 J and FS 400/450/480 O sheets list 0000 997 1304 as a compression spring, at positions 26 and 9 respectively. Their separate spring 0000 997 1701 is not this replacement. Catalog positions differ from TI figure item 1. FS 480 is not admitted from the shared sheet.
  • Historical source guidance; no present-day stock guarantee or verified physical interchange. No hardware operation was performed.

Source: TI 20/1998, p. 2 — Page 2 complete section 2, handlebar figure, summary and remark.

Part numbers (2)
  • 0000 997 1302 — Original helical springRetained for other models · Handlebar clamp between moldings; named FS models only
  • 0000 997 1304 — New helical springReplaces original; introduction in progress · Handlebar clamp between moldings; named FS models only

Wrong number or missing part for the FS 400, FS 450, FS 480? Report a correction →