← Edgers & other equipment · series 4130

Stihl 4130 · Section A · 1 of 9 · 23 parts

Crankcase, Cylinder

Fits FC 44.

Parts diagrams →

Historical fitment & changes (2) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
1101112131415161718192202122456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (23)

PosPart numberDescriptionQty
1 4130 020 2105 Crankcase 1
2 9503 003 9955 Grooved ball bearing 0.5x1.125x0.312" 1
4 9633 003 9985 Oil seal 1
5 9503 003 9957 Grooved ball bearing 0.5x1.125x0.312" 1
6 9291 021 3932 Washer 23.1x12.8x0.9 1
7 4130 030 0400 Crankshaft 1
8 4130 036 8600 Woodruff key 1
9 4130 020 1200 Cylinder with piston Ø 35 mm 1
10 4130 030 2000 Piston with connecting rod 1
11 4130 034 3000 Piston ring 1
12 4130 029 2300 Cylinder gasket 1
13 9022 341 1310 Spline screw IS-M6x18 2
14 4130 084 1150 Spiral housing 1
15 4130 028 0205 Spline screw TT 5.2x14.3 4
16 4130 029 0500 Gasket 1
17 4130 020 0500 Diaphragm carrier 1
18 4130 141 4100 Diaphragm 1
19 4130 141 2400 Support plate 1
20 9099 021 2360 Self-tapping screw 3.5x9.5 1
21 4130 028 0200 Spline screw TT 4.8x19 4
22 4112 400 7001 Spark plug NGK BMR 6A 1
22 0000 400 7002 NLA Spark plug AC CSR 45 1
Not numbered on the diagram — assemblies, kits and options
— 4130 020 0205 Engine 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · FC 44

FC 44: engine construction and intended use

30.2 cm³ occasional-use edger uses the FS36/40/44 engine design; 6.2 kg includes its blade.

  • Designed for occasional users edging small/medium plots, grass borders around fields, lawns, flowerbeds and trees. Adjustable loop handle permits upright working position. Weight 6.2 kg (13.7 lb) WITH CUTTING BLADE; fuel condition unspecified. Engine 30.2 cm³ (1.84 cu.in), 34.8 mm bore, 31.8 mm stroke; output 0.7 kW (0.95 HP) to ISO8893.
  • Compact single-cylinder two-stroke described as identical to FS36/40/44 engine. One-piece aluminium die-cast crankcase open at carburetor side, flange-mounted diaphragm carrier; special-aluminium cylinder with impregnated bore and aluminium piston with ONE compression ring. Crankshaft ball bearings; big/small ends use needle cages. No complete engine interchange procedure inferred.
  • Smooth surfaces aid cleaning; housing reduces contact with hot parts. Exhaust and heated cooling air discharge rearward away from operator; large-volume muffler plus intake-air silencing. Sealed electronic ignition described as maintenance-free, not exemption from all checks. Illustrations show complete edger/use context, not dimensional or mounting templates.
  • Historical TI 24/1994 for FC44 only; shared-engine or design-principle comparisons are not universal loose-part interchange. No serial cutoff supplied. Source date November 10, 1994; referenced manuals are not whole-manual acceptance. Owner-manual precautions remain required. No physical interchange test was performed.

Source: TI 24/1994, p. 1 · TI 24/1994, p. 2 · TI 24/1994, p. 4 · TI 24/1994, p. 5 — engine construction and intended use.

No additional parts-table entry added.

Service note · FC 44

FC 44: component-specific tightening torques

Clutch drum 2.5 Nm differs from clutch 17 Nm; depth-wheel 21 Nm is not a blade-nut setting.

  • Source Nm / lbf.ft pairs, with exact thread/joint association: captive spline IS8–32 inch, clutch drum to crankshaft 2.5/1.8; clutch 3/8–24 inch, clutch to crankshaft 17/12.5; B3.5×9.5, backing plate/diaphragm/diaphragm carrier AND frame on muffler 2/1.5; B3.9×19, control handle 2.5/1.8; IS-DG5×16, loop handle 2.5/1.8.
  • IS-TT4.8×19: fan housing to spiral housing 3.0/2.2; diaphragm carrier to crankcase 4.5/3.3. IS-DG5×24: shroud to fan housing 3.5/2.6; clutch/starter housing to fan housing 3.5/2.6. IS-DG5×60: shroud/carburetor/diaphragm carrier 3.5/2.6; muffler to cylinder 6.5/4.8 (printed German “Schalldämpfer am Zylinder”).
  • IS-M4×20, ignition module to cylinder 3.5/2.6; IS-M5×18, clamp on clutch housing 6.5/4.8; IS-M6×18, cylinder to crankcase 14.0/10.3; IS-TT5.2×14, spiral housing to crankcase 14.0/10.3; M6×50 pan-head, clamp screw in loop handle 3.5/2.6; IS-M11×10 screw plug, gearhead 10.0/7.5.
  • M14×1.25 spark plug 19.0/14.0; P5×14 special spline, filter cover to shroud 2.5/1.8; IS-M6×20, gearhead clamp screw 7.5/5.5; IS-M6×25, clamp to deflector 7.5/5.5; M6 clamp screw, clamp on deflector 7.5/5.5; IS-DG5×12, clamp for clamp screw AND flap to deflector 5.5/4.0; M10 collar screw, depth wheel 21/15.5.
  • All 24 numeric torque rows preserved. Inch-thread asterisks apply to IS8–32 and 3/8–24, not adhesive requirements. Table gives NO M8 BLADE-NUT torque. Do not transfer 21 Nm wheel or 17 Nm clutch setting to blade nut. Rounded imperial values retained as printed; no live tightening validation.
  • Historical TI 24/1994 for FC44 only; shared-engine or design-principle comparisons are not universal loose-part interchange. No serial cutoff supplied. Source date November 10, 1994; referenced manuals are not whole-manual acceptance. Owner-manual precautions remain required. No physical interchange test was performed.

Source: TI 24/1994, p. 6 — component-specific tightening torques.

No additional parts-table entry added.

Wrong number or missing part for the FC 44? Report a correction →