Stihl 4130 · Section B · 2 of 9 · 35 parts
Ignition system, Rewind starter
Fits FC 44.
Historical fitment & changes (7) — includes parts and conditions not shown on this drawing.
Parts (35)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4130 400 1250 | Flywheel Fitment / change note → | 1 |
| 2 | 4130 998 1400 | Torsion spring | 2 |
| 3 | 4130 195 7200 | Pawl | 2 |
| 4 | 1114 195 7800 | Pin | 2 |
| 5 | 0000 958 0924 | Washer | 1 |
| 6 | 4130 400 1300 | Ignition module Fitment / change note → | 1 |
| 7 | 1130 405 1000 | Spark plug boot | 1 |
| 8 | 0000 998 0614 | Torsion spring | 1 |
| 9 | 9291 021 0100 | Washer 4.3 | 2 |
| 10 | 9022 371 0710 | Spline screw IS-M4x20 | 2 |
| 11 | 4130 084 1002 | Fan housing | 1 |
| 12 | 4130 195 0700 | Rewind starter housing | 1 |
| 13 | 9075 478 4155 | Pan head self-tapping screw IS-D5x24 | 4 |
| 14 | 4130 084 9100 | Bushing | 1 |
| 15 | 4130 195 1600 | Rewind spring | 1 |
| 16 | 4130 195 0400 | Rope rotor | 1 |
| 17 | 0000 958 1804 | Washer | 1 |
| 18 | 9455 621 1670 | Circlip 16x1 | 1 |
| 19 | 4130 195 3400 | Starter grip | 1 |
| 20 | 4130 195 8200 | Starter rope Ø 3.5x850 mm | 1 |
| 21 | 0000 190 3400 | Starter grip ElastoStart Ø 3 mm Fitment / change note → → replaced by 0000 190 3403, 0000 190 3403 TI 42/1999 option | 1 |
| 22 | 0000 195 8200 | Starter rope Ø 3x800 mm Fitment / change note → option | 1 |
| 23 | 0000 195 7000 | Cap option | 1 |
| 24 | 4130 028 0200 | Spline screw TT 4.8x19 | 4 |
| 25 | 4130 440 1110 | Short circuit wire 600 mm / 23.6'' | 1 |
| 26 | 0751 030 8454 | Spade terminal no longer available from factory | 1 |
| 27 | 0751 030 8404 | Terminal socket 6.3-1 no longer available from factory | 1 |
| 28 | 0751 030 8471 | Grommet no longer available from factory | 1 |
| 29 | 4203 711 7201 | Hose 960 mm / 37 13/16'' | 1 |
| 30 | 4130 182 2100 | Support | 1 |
| 31 | 4119 431 6700 | Terminal socket no longer available from factory | 1 |
| 32 | 0000 967 3693 | Warning pictogram Filler cap | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 4130 007 1028 | Rewind starter kit | 1 |
| — | 0000 930 2203 | Starter rope Ø 3.5 mm x 30.5 m not illustratedoption | 1 |
| — | 0000 930 2208 NLA | Starter rope Ø 3 mm x 30.5 m not illustratedoption | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Historical fitment · FS 36 / FS 40 / FS 44 / FC 44
FS 36 / FS 40 / FS 44 / FC 44: series 4130 replacement ignition assignment
4130 400 1300 with flywheel 4130 400 1250; ignition lead not replaceable.
- Printed series 4130. Use 4130 400 1300 with flywheel 4130 400 1250.
- The asterisk means ignition lead not replaceable; it is not a zero or unspecified cut length.
- TI01/1999 lists replacement combinations for the then-current machines, not every earlier configuration. Older machines are referred to Spare Parts for Previous Models in their own illustrated parts lists; no serial cutoff is supplied here.
- Use only the listed ignition-module/flywheel combinations. The source warns that incorrect combinations can cause excessive RPM or running in reverse; sharing a module number does not make all flywheels interchangeable.
- Universal replacement modules may differ from production modules in maker, shape and part number. The source describes installation/function compatibility within its assignments, not universal compatibility or a project hardware test.
- Some replacement modules require shortening the ignition lead and/or short-circuit wire and crimping a different short-circuit connector. The table gives ignition-lead lengths only; it supplies neither a short-circuit-wire length nor a connector part number. Do not infer that every row needs modification.
- Only the named models and printed series are covered. A shared IPL sheet does not extend this assignment to unnamed models or modern MS equivalents. This 1999 USA bulletin is historical guidance, not current availability.
- The bulletin prints series 4130; the retained exact-model ignition sheets are cataloged under 4130, 4144. This link is an exact model-label navigation aid, not proof that the printed series identifiers are equivalent. Verify the actual machine configuration.
Source: TI 1/1999, p. 1 · TI 1/1999, p. 3 — 1.1 general restrictions and 1.2.2 power-tool assignments.
Part numbers (2)
- 4130 400 1300 — Replacement ignition moduleAssigned component · FS 36 / FS 40 / FS 44 / FC 44, printed series 4130, listed combination only
- 4130 400 1250 — Assigned flywheelRequired pairing · FS 36 / FS 40 / FS 44 / FC 44, printed series 4130
Service note · FC 44
FC 44: ignition settings and starter clearances
Spark-plug gap is 0.7–0.8 mm; rewind-spring spare travel is ¼–1¾ rotor turns.
- Electronic breakerless magneto with flywheel and ignition module containing trigger unit. Coil/flywheel air gap 0.1–0.5 mm (0.004–0.020 in); timing 1.3–1.9 mm (0.05–0.075 in) BEFORE TDC at 6000 rpm. No adjustable-timing mechanism inferred.
- Suppressed plugs GM AC CSR45, Champion RCJ8 or NGK BMR6A; electrode gap 0.7–0.8 mm (0.03 in); thread M14×1.25, thread reach 9.5 mm (0.37 in). Do not use a neighboring model’s 0.5 mm gap or longer reach.
- TWO-PAWL rewind starter. Spring spare travel¼–1¾ TURNS OF ROPE ROTOR (not total winding turns); pawl/pin clearance 0.05–0.4 mm (0.0020–0.016 in). Starter rope diameter 3.5 mm (0.14 in), length 850 mm (33.5 in). No rope part number or complete spring installation procedure supplied.
- Historical TI 24/1994 for FC44 only; shared-engine or design-principle comparisons are not universal loose-part interchange. No serial cutoff supplied. Source date November 10, 1994; referenced manuals are not whole-manual acceptance. Owner-manual precautions remain required. No physical interchange test was performed.
Source: TI 24/1994, p. 2 · TI 24/1994, p. 4 · TI 24/1994, p. 5 — ignition settings and starter clearances.
No additional parts-table entry added.
Historical fitment · FC 44 / FS 36 / FS 40 / FS 44
FC 44 / FS 36 / FS 40 / FS 44: ElastoStart special-accessory retrofit
0000 190 3400 includes required 3 x 800 mm rope 0000 195 8200.
- The new ElastoStart is offered with immediate effect as a SPECIAL ACCESSORY, not stated standard production equipment. No changes to the rewind starter are necessary to retrofit it, but installation differs slightly from the standard grip. No serial cutoff or verified production date is supplied.
- The page 3 spare table lists complete ElastoStart 0000 190 3400 INCLUDING item 1, starter rope 0000 195 8200, dimension 3 x 800 mm. Item 1 here is a spare-table position, not construction drawing item 1 (grip). No separate internal component ordering numbers or additional quantity claims are printed.
- Printed model-series assignment: FC 44 and FS 36/40/44 — 4130.
- Historical TI 07/1996 guidance for BG 72, FC 44, FC 72, FS 36, FS 40, FS 44, FS 72, FS 74 and FS 76 only. No later variant, chainsaw or other shared-sheet model is included. No hardware operation was performed; availability and comfort claims are historical, not current stock or a measured project result.
Source: TI 7/1996, p. 1 · TI 7/1996, p. 3 — FC 44 / FS 36 / FS 40 / FS 44: ElastoStart special-accessory retrofit.
Part numbers (2)
- 0000 190 3400 — ElastoStart complete assemblyincludes item 1 starter rope · FC 44, FS 36, FS 40, FS 44; TI07/1996 ElastoStart only
- 0000 195 8200 — Starter rope 3 x 800 mmrequired rope; included item 1 · FC 44, FS 36, FS 40, FS 44; TI07/1996 ElastoStart only
Service note · BG 72 / FC 44 / FS 36 / FS 40 / FS 44 / FC 72 / FS 72 / FS 74 / FS 76
ElastoStart construction and force path: spring-label conflict retained
Spring cushioning is qualitative; the function paragraph calls the spring (3), but the key and drawing use (4).
- Construction key: 1 grip, 2 cap, 3 sleeve, 4 helical spring, 5 washer, 6 starter rope. The drawing shows upper and lower washers both labeled 5. In the relaxed position the sleeve, spring and washers are retained by stop lug 7. These are component labels, not independently supplied spare numbers.
- During cranking the described load path is grip 1 → lower washer 5 → helical spring → upper washer 5 → sleeve 3 → rope 6. Engine compression compresses the spring and its peaks are cushioned. The printed function paragraph says helical spring (3), although its opening paragraph, page 1 key and both drawings assign spring 4 and sleeve 3. This source contradiction remains explicit; the immutable text is not rewritten.
- After the first compression stroke the source describes grip force as practically uniform. Above an unspecified spring-determined starting-force level the spring becomes fully compressed and effort transfers directly from grip to rope. No force threshold, spring rate, travel limit or replacement spring specification is given.
- Page 1 plots tensile force versus hand travel, with thick ElastoStart and thin standard-grip curves. Axes have no numerical values; the illustration is qualitative and does not establish a percentage reduction. Construction differs from the chainsaw version referenced in TI 29/1992; that TI is outside the retained inventory. No missing chainsaw construction or interchange claim is imported; current construction is fully described here.
- The TI header prints BG 72 as series 4227, while the retained exact-model BG 72 rewind-starter IPL is cataloged under 4133 (4227 has BG 75). The BG 72 link is exact-model navigation only: this unresolved series conflict is not silently corrected and does not establish BG 75 fitment or equivalence of series.
- Historical TI 07/1996 guidance for BG 72, FC 44, FC 72, FS 36, FS 40, FS 44, FS 72, FS 74 and FS 76 only. No later variant, chainsaw or other shared-sheet model is included. No hardware operation was performed; availability and comfort claims are historical, not current stock or a measured project result.
Source: TI 7/1996, p. 1 · TI 7/1996, p. 2 — ElastoStart construction and force path: spring-label conflict retained.
No additional parts-table entry added.
Service note · BG 72 / FC 44 / FS 36 / FS 40 / FS 44 / FC 72 / FS 72 / FS 74 / FS 76
ElastoStart repair limit: rope only, otherwise complete assembly
The cutaway is not permission to repair the grip internals.
- Repairs are LIMITED TO REPLACEMENT OF THE STARTER ROPE. A faulty ElastoStart can only be replaced as a COMPLETE ASSEMBLY. The cutaway and named spring/sleeve/washers explain function, not approved internal repair or separately available components.
- For this accessory the complete assembly is 0000 190 3400 and the only separately listed replacement is rope 0000 195 8200. No spring substitute, preload setting or procedure to rebuild the grip is supplied.
- The TI header prints BG 72 as series 4227, while the retained exact-model BG 72 rewind-starter IPL is cataloged under 4133 (4227 has BG 75). The BG 72 link is exact-model navigation only: this unresolved series conflict is not silently corrected and does not establish BG 75 fitment or equivalence of series.
- Historical TI 07/1996 guidance for BG 72, FC 44, FC 72, FS 36, FS 40, FS 44, FS 72, FS 74 and FS 76 only. No later variant, chainsaw or other shared-sheet model is included. No hardware operation was performed; availability and comfort claims are historical, not current stock or a measured project result.
Source: TI 7/1996, p. 1 · TI 7/1996, p. 2 · TI 7/1996, p. 3 — ElastoStart repair limit: rope only, otherwise complete assembly.
Part numbers (2)
- 0000 190 3400 — ElastoStart complete assemblyincludes item 1 starter rope · BG 72, FC 44, FS 36, FS 40, FS 44, FC 72, FS 72, FS 74, FS 76; TI07/1996 ElastoStart only
- 0000 195 8200 — Starter rope 3 x 800 mmrequired rope; included item 1 · BG 72, FC 44, FS 36, FS 40, FS 44, FC 72, FS 72, FS 74, FS 76; TI07/1996 ElastoStart only
Service note · BG 72 / FC 44 / FS 36 / FS 40 / FS 44 / FC 72 / FS 72 / FS 74 / FS 76
ElastoStart installation: outside-in guide threading and rotor knot
The two installation steps require a simple overhand knot at the rope rotor.
- For installing ElastoStart WITH STARTER ROPE: thread the rope through the rope-guide bushing FROM OUTSIDE the starter housing. Then thread the rope into the rope rotor and secure it with a SIMPLE OVERHAND knot. Page 2 shows the guide/rotor route and knot; it does not prescribe a different multi-loop knot.
- These are accessory-specific installation changes, not a complete rewind-starter overhaul. No rotor pretension turn count, fastener torque or universal winding direction is printed; none is inferred from the arrow or from another model. The separate page 3 grip knot applies when replacing the rope.
- The TI header prints BG 72 as series 4227, while the retained exact-model BG 72 rewind-starter IPL is cataloged under 4133 (4227 has BG 75). The BG 72 link is exact-model navigation only: this unresolved series conflict is not silently corrected and does not establish BG 75 fitment or equivalence of series.
- Historical TI 07/1996 guidance for BG 72, FC 44, FC 72, FS 36, FS 40, FS 44, FS 72, FS 74 and FS 76 only. No later variant, chainsaw or other shared-sheet model is included. No hardware operation was performed; availability and comfort claims are historical, not current stock or a measured project result.
Source: TI 7/1996, p. 1 · TI 7/1996, p. 2 · TI 7/1996, p. 3 — ElastoStart installation: outside-in guide threading and rotor knot.
Part numbers (1)
- 0000 195 8200 — Starter rope 3 x 800 mmrequired rope; included item 1 · BG 72, FC 44, FS 36, FS 40, FS 44, FC 72, FS 72, FS 74, FS 76; TI07/1996 ElastoStart only
Service note · BG 72 / FC 44 / FS 36 / FS 40 / FS 44 / FC 72 / FS 72 / FS 74 / FS 76
ElastoStart rope replacement: mandatory 8200 rope and grip knot
Ease off cap, remove old rope, fit 0000 195 8200 with simple overhand grip knot, refit cap.
- Four printed steps: ease the cap off the starter grip; remove remaining rope from grip AND rope rotor; fit starter rope 0000 195 8200 in the same way as the standard rope, but secure it IN THE GRIP only with a SIMPLE OVERHAND knot; refit the cap in the grip. The drawing shows cap removal and rope/knot insertion into the grip.
- The source says rope 0000 195 8200 MUST be used to guarantee correct ElastoStart operation; its listed dimension is 3 x 800 mm. Matching diameter/length alone is not evidence that a substitute rope is approved. Page 2 separately requires a simple overhand knot at the rotor.
- The same-as-standard instruction refers to the base starter operation; this note preserves the complete accessory-specific delta, not a standalone base-starter repair manual. No extra winding count, trimming allowance or rope material specification is invented.
- The TI header prints BG 72 as series 4227, while the retained exact-model BG 72 rewind-starter IPL is cataloged under 4133 (4227 has BG 75). The BG 72 link is exact-model navigation only: this unresolved series conflict is not silently corrected and does not establish BG 75 fitment or equivalence of series.
- Historical TI 07/1996 guidance for BG 72, FC 44, FC 72, FS 36, FS 40, FS 44, FS 72, FS 74 and FS 76 only. No later variant, chainsaw or other shared-sheet model is included. No hardware operation was performed; availability and comfort claims are historical, not current stock or a measured project result.
Source: TI 7/1996, p. 2 · TI 7/1996, p. 3 — ElastoStart rope replacement: mandatory 8200 rope and grip knot.
Part numbers (1)
- 0000 195 8200 — Starter rope 3 x 800 mmrequired rope; included item 1 · BG 72, FC 44, FS 36, FS 40, FS 44, FC 72, FS 72, FS 74, FS 76; TI07/1996 ElastoStart only
Wrong number or missing part for the FC 44? Report a correction →