Stihl 4130 · Section D · 4 of 9 · 37 parts
Carburetor WT-160B
Fits FC 44.
Historical fitment & changes (1) — includes parts and conditions not shown on this drawing.
Parts (37)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 1114 121 7800 | Strainer | 1 |
| 2 | 1121 121 4801 | Pump diaphragm | 1 |
| 3 | 1120 129 0905 | Gasket | 1 |
| 4 | 4116 121 5100 | Inlet needle | 1 |
| 5 | 1120 122 3001 | Spring | 1 |
| 6 | 4117 122 9402 | Plug | 1 |
| 7 | 1120 129 0900 | Gasket | 1 |
| 8 | 1113 121 4705 | Metering diaphragm | 1 |
| 9 | 4117 121 0803 | End cover | 1 |
| 10 | 1114 122 7100 | Screw | 1 |
| 11 | 4117 122 3006 | Spring | 1 |
| 12 | 4117 122 6200 | Idle speed adjustment screw | 1 |
| 13 | 1113 121 5000 | Inlet control lever | 1 |
| 14 | 1113 121 9200 | Spindle | 1 |
| 15 | 1114 122 7400 | Round head screw | 1 |
| 16 | 1120 121 5405 | Valve jet | 1 |
| 17 | 4130 120 8600 | Non-return valve | 1 |
| 18 | 1113 121 0800 | End cover | 1 |
| 19 | 1106 122 7400 | Round head screw | 4 |
| 20 | 4117 122 3200 | Torsion spring | 1 |
| 21 | 4130 120 7101 | Throttle shaft with lever | 1 |
| 22 | 1117 122 9000 | E-clip | 1 |
| 23 | 4130 121 3300 | Throttle shutter | 1 |
| 24 | 1110 122 7400 | Round head screw | 2 |
| 25 | 1116 122 3000 | Spring | 1 |
| 26 | 1116 122 4200 | Ball | 1 |
| 27 | 4130 121 3000 | Choke shaft | 1 |
| 28 | 4130 121 2900 | Choke shutter | 1 |
| 30 | 1120 122 6805 | Low speed adjustment screw | 1 |
| 31 | 4117 122 3007 | Spring | 1 |
| 32 | 4130 122 6700 | High speed adjustment screw | 1 |
| 33 | 4130 121 8600 | Washer | 1 |
| 34 | 4130 120 8700 | Control valve | 1 |
| 35 | 4130 122 3905 | Connector | 1 |
| 36 | 4130 122 3900 | Elbow connector | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 4130 120 0601 | Carburetor WT-160B | 1 |
| — | 4130 007 1060 | Set of carburetor parts | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · FC 44
FC 44: fuel mixture, choke and carburetor test conditions
Walbro WT160 basic settings and blade-free cutoff speed retain their exact conditions.
- Diaphragm-controlled Walbro WT160, flange-mounted to diaphragm carrier, has max-speed control valve and integral fuel pump. Manual pump primes carburetor before start; surplus fuel returns automatically to tank. Tank 0.51 L (1.1 US pt). Historical fuel instruction: brand-name regular gasoline unleaded OR leaded; 50:1 with STIHL1:50 oil, 25:1 with OTHER branded two-stroke oils. Do not collapse to one universal oil ratio.
- Ring-shaped foam filter 1; cover 2 rotates choke shutter between end-stop-defined RUN/CHOKE. FS44-type controls: stop slide 3, trigger interlock 4, trigger housing 5, trigger/latch 6. Starting-throttle position engages latch in housing notch. These are source controls, not permission to actuate unattended.
- Basic H and L settings EACH back off ONE FULL TURN; printed parenthesis says screws initially HARD AGAINST THEIR SEATS. Preserve wording as historical reference, not a recommendation to force/torque delicate needles. No seating torque or complete live-tuning procedure is supplied.
- Max permissible cut-off speed 9300 rpm ±700 WITHOUT CUTTING BLADE, not loaded working speed. Idle 3100 rpm. Carburetor leakage closing pressure 0.8 bar (11.6 psi). Crankcase test 0.5 bar (7.25 psi) GAUGE pressure and 0.4 bar (5.8 psi) UNDER VACUUM; latter is vacuum magnitude, not a second positive pressure. No test duration/leakdown limit given.
- Historical TI 24/1994 for FC44 only; shared-engine or design-principle comparisons are not universal loose-part interchange. No serial cutoff supplied. Source date November 10, 1994; referenced manuals are not whole-manual acceptance. Owner-manual precautions remain required. No physical interchange test was performed.
Source: TI 24/1994, p. 2 · TI 24/1994, p. 3 · TI 24/1994, p. 4 · TI 24/1994, p. 5 · TI 24/1994, p. 6 — fuel mixture, choke and carburetor test conditions.
No additional parts-table entry added.
Wrong number or missing part for the FC 44? Report a correction →