Stihl 4130 · Section J · 9 of 9 · 24 parts
Deflector, Tools, Extras
Fits FC 44.
Historical fitment & changes (5) — includes parts and conditions not shown on this drawing.
Parts (24)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4133 713 4506 | Deflector | 1 |
| 2 | 4133 716 6505 | Clamp | 1 |
| 3 | 9214 320 0900 | Lock nut M6 | 2 |
| 4 | 9022 341 1350 | Spline screw IS-M6x25 | 1 |
| 5 | 9291 021 0140 | Washer 6.4 | 1 |
| 6 | 4133 710 9500 | Adjusting screw | 1 |
| 7 | 4133 716 6600 | Clamp | 1 |
| 8 | 9075 478 4095 | Pan head self-tapping screw IS-D5x12 | 3 |
| 9 | 4133 712 1000 | Wheel Fitment / change note → | 1 |
| 10 | 4133 712 1001 | Wheel Fitment / change note → option | 1 |
| 11 | 4133 713 6501 | Collar screw | 1 |
| 12 | 9291 021 0220 | Washer 13 | 1 |
| 13 | 9291 021 0200 | Washer 10.5 | 1 |
| 14 | 4133 716 3200 | Skirt | 1 |
| 15 | 0000 958 0512 | Washer | 1 |
| 16 | 4133 713 4101 | Blade Ø 200x2.4 mm / 7 7/8'' x 1/10'' Fitment / change note → | 1 |
| 17 | 0000 967 3730 | Warning pictogram | 1 |
| 18 | not sold separately | Combination wrench not available as a separate item | 1 |
| 19 | 1129 890 3401 | Combination wrench option | 1 |
| 20 | 4133 893 7800 | Locking pin option | 1 |
| 21 | 0000 890 2300 NLA | Screwdriver option | 1 |
| 22 | 0812 370 1000 | Screwdriver T27x120x70 | 1 |
| 23 | 0000 884 0307 | Safety glasses | 1 |
| 24 | 0000 891 0801 NLA | Tool roll option | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · FC 44
FC 44: approved blade, left-hand shaft and deflector orientation
Only the listed 200 mm blade is approved in this TI; wheel-side changes require flap relocation.
- For safety reasons TI approves ONLY blade 4133 713 4101, 200 mm (8 in) long. Flexible drive shaft in curved tube transmits power to gearhead. Gearhead uses same design principle as FS66–106; output shaft as FC72 with M8 LEFT-HAND thread. These comparisons do not assign FC44 blade or gearhead to those models.
- Illustration identifies blade 7, shaft 8, thrust plate 9, thrust washer 10, nut 11. Place blade on thrust plate, then thrust washer over shaft, secure with nut. Nut has CAPTIVE SPRING WASHER; if it loses resilience, replace WHOLE NUT. No blade-nut tightening torque printed in this section or torque table; do not substitute the 21 Nm depth-wheel value.
- Deflector 12 rotates on gearhead to set depth: release clamp screw 13, rotate, retighten. Arrow on OPEN SIDE MUST FACE AWAY FROM OPERATOR so debris is diverted away from operator and machine. Cutting guide 14 indicates blade position; flexible flap 15 extends deflector and diverts debris.
- Depth wheel 16 supports part of weight and maintains depth; it may mount EITHER SIDE of deflector, but rubber flap position MUST THEN CHANGE to match. Diagram orientation does not override that explicit side-change condition.
- Historical TI 24/1994 for FC44 only; shared-engine or design-principle comparisons are not universal loose-part interchange. No serial cutoff supplied. Source date November 10, 1994; referenced manuals are not whole-manual acceptance. Owner-manual precautions remain required. No physical interchange test was performed.
Source: TI 24/1994, p. 2 · TI 24/1994, p. 3 · TI 24/1994, p. 4 — approved blade, left-hand shaft and deflector orientation.
Part numbers (1)
- 4133 713 4101 — 200 mm /8 in cutting bladeonly TI-approved blade · FC44 TI24/1994 approved blade, left-hand shaft and deflector orientation
Service note · FC 44
FC 44: depth-wheel choices and workshop kits
Printed metric/inch wheel dimensions disagree; both remain explicit.
- Depth wheel 4133 712 1000: diameter 127 mm (printed 5 in), width 32 mm (printed 1 in). Wheel 4133 712 1001: diameter 67 mm (printed 3 in), width 50 mm (printed 2 in). The 32 mm/1 in and 67 mm/3 in pairs are NOT exact conversions; retain printed dimensions without silently changing metric sizes or assuming inch dimensions control fit.
- Safety goggles to national safety code, with no order number. STIHL multipurpose grease 0781 120 1109 and gear lubricant 0781 120 1117, each 80 g (2¾ oz) tube; distinct lubricants, not an interchangeable application instruction.
- Service-shop carburetor parts kit 4130 007 1060; gasket set 4130 007 1050; gasket panel 0457 281 3803 lists FS36/40/44/48/52/56/62/66/81/86; data chart 0457 265 0000 is labeled for FS36/40/44. They are listed references for FC44 service, not authority to assign all FC44 hardware to those other models.
- Historical TI 24/1994 for FC44 only; shared-engine or design-principle comparisons are not universal loose-part interchange. No serial cutoff supplied. Source date November 10, 1994; referenced manuals are not whole-manual acceptance. Owner-manual precautions remain required. No physical interchange test was performed.
Source: TI 24/1994, p. 5 — depth-wheel choices and workshop kits.
Part numbers (8)
- 4133 712 1000 — 127 mm depth wheel, 32 mm widthprinted inch discrepancy retained · FC44 TI24/1994 depth-wheel choices and workshop kits
- 4133 712 1001 — 67 mm depth wheel, 50 mm widthprinted inch discrepancy retained · FC44 TI24/1994 depth-wheel choices and workshop kits
- 0781 120 1109 — Multipurpose grease 80 glisted accessory · FC44 TI24/1994 depth-wheel choices and workshop kits
- 0781 120 1117 — Gear lubricant 80 glisted accessory · FC44 TI24/1994 depth-wheel choices and workshop kits
- 4130 007 1060 — Carburetor parts kitworkshop · FC44 TI24/1994 depth-wheel choices and workshop kits
- 4130 007 1050 — Gasket setworkshop · FC44 TI24/1994 depth-wheel choices and workshop kits
- 0457 281 3803 — Gasket panelnamed FS reference models · FC44 TI24/1994 depth-wheel choices and workshop kits
- 0457 265 0000 — Data chartFS36/40/44 reference · FC44 TI24/1994 depth-wheel choices and workshop kits
Service note · FC 44
FC 44: component-specific tightening torques
Clutch drum 2.5 Nm differs from clutch 17 Nm; depth-wheel 21 Nm is not a blade-nut setting.
- Source Nm / lbf.ft pairs, with exact thread/joint association: captive spline IS8–32 inch, clutch drum to crankshaft 2.5/1.8; clutch 3/8–24 inch, clutch to crankshaft 17/12.5; B3.5×9.5, backing plate/diaphragm/diaphragm carrier AND frame on muffler 2/1.5; B3.9×19, control handle 2.5/1.8; IS-DG5×16, loop handle 2.5/1.8.
- IS-TT4.8×19: fan housing to spiral housing 3.0/2.2; diaphragm carrier to crankcase 4.5/3.3. IS-DG5×24: shroud to fan housing 3.5/2.6; clutch/starter housing to fan housing 3.5/2.6. IS-DG5×60: shroud/carburetor/diaphragm carrier 3.5/2.6; muffler to cylinder 6.5/4.8 (printed German “Schalldämpfer am Zylinder”).
- IS-M4×20, ignition module to cylinder 3.5/2.6; IS-M5×18, clamp on clutch housing 6.5/4.8; IS-M6×18, cylinder to crankcase 14.0/10.3; IS-TT5.2×14, spiral housing to crankcase 14.0/10.3; M6×50 pan-head, clamp screw in loop handle 3.5/2.6; IS-M11×10 screw plug, gearhead 10.0/7.5.
- M14×1.25 spark plug 19.0/14.0; P5×14 special spline, filter cover to shroud 2.5/1.8; IS-M6×20, gearhead clamp screw 7.5/5.5; IS-M6×25, clamp to deflector 7.5/5.5; M6 clamp screw, clamp on deflector 7.5/5.5; IS-DG5×12, clamp for clamp screw AND flap to deflector 5.5/4.0; M10 collar screw, depth wheel 21/15.5.
- All 24 numeric torque rows preserved. Inch-thread asterisks apply to IS8–32 and 3/8–24, not adhesive requirements. Table gives NO M8 BLADE-NUT torque. Do not transfer 21 Nm wheel or 17 Nm clutch setting to blade nut. Rounded imperial values retained as printed; no live tightening validation.
- Historical TI 24/1994 for FC44 only; shared-engine or design-principle comparisons are not universal loose-part interchange. No serial cutoff supplied. Source date November 10, 1994; referenced manuals are not whole-manual acceptance. Owner-manual precautions remain required. No physical interchange test was performed.
Source: TI 24/1994, p. 6 — component-specific tightening torques.
No additional parts-table entry added.
Service note · FC 44
FC 44: testing tools retain adapter and alternative requirements
The testing kit contains only footnote 1-marked tools, not the entire tool table.
- Each disclosed part retains its printed tool/application. Footnote 1 marks sealing plate 0000 855 8106, nipple 0000 855 9200, bushing 0000 963 1008, tester 1106 850 2905, gauge 1111 890 6400 and flange 1119 850 4201 as included in kit 0000 890 1710; not every tool in the list.
- Nipple 0000 855 9200 REQUIRES fuel line 1110 141 8600 as connection ADAPTER. A10 pliers 0811 611 8200 may substitute for A19 pliers 0811 611 8380 (external circlips), not C19 internal pliers. Press sleeve 1114 893 4601 may substitute for 4112 893 2401. Do not attach that footnote to carburetor guide on next row.
- Starting unit during repairs/maintenance requires local/national regulations and owner-manual safety precautions. Listed tools and numeric test data are reference capability, not an authorized unattended actuation or a complete bench procedure.
- Historical TI 24/1994 for FC44 only; shared-engine or design-principle comparisons are not universal loose-part interchange. No serial cutoff supplied. Source date November 10, 1994; referenced manuals are not whole-manual acceptance. Owner-manual precautions remain required. No physical interchange test was performed.
Source: TI 24/1994, p. 7 — testing tools retain adapter and alternative requirements.
Part numbers (21)
- 0000 850 3501 — Crankcase vacuum pumpleak test · FC44 TI24/1994 testing tools retain adapter and alternative requirements
- 0000 855 8106 — Sealing plateleak test; kit · FC44 TI24/1994 testing tools retain adapter and alternative requirements
- 0000 855 9200 — Nipplecarb leak test; kit; adapter required · FC44 TI24/1994 testing tools retain adapter and alternative requirements
- 0000 963 1008 — Bushingcrankcase leak test; kit · FC44 TI24/1994 testing tools retain adapter and alternative requirements
- 0811 611 8380 — A19 pliersexternal circlips rope rotor/gearhead · FC44 TI24/1994 testing tools retain adapter and alternative requirements
- 0811 641 8380 — C19 pliersinternal gearhead circlips · FC44 TI24/1994 testing tools retain adapter and alternative requirements
- 0812 542 2104 — IS5×120×6.3 bittorque wrench; IS screws · FC44 TI24/1994 testing tools retain adapter and alternative requirements
- 1106 850 2905 — Carburetor/crankcase testerleak test; kit · FC44 TI24/1994 testing tools retain adapter and alternative requirements
- 1111 890 6400 — Setting gaugeignition coil/flywheel gap; kit · FC44 TI24/1994 testing tools retain adapter and alternative requirements
- 1119 850 4201 — Flangecrankcase leak test; kit · FC44 TI24/1994 testing tools retain adapter and alternative requirements
- 4112 893 1200 — Piston locking screwblock crankshaft · FC44 TI24/1994 testing tools retain adapter and alternative requirements
- 4112 893 2401 — Press sleeveremove/install ball bearing and oil seal · FC44 TI24/1994 testing tools retain adapter and alternative requirements
- 4130 855 7700 — Guidecarburetor adjustment aid · FC44 TI24/1994 testing tools retain adapter and alternative requirements
- 4130 890 3600 — Wrenchremove/install clutch · FC44 TI24/1994 testing tools retain adapter and alternative requirements
- 5910 890 2400 — QI5×150 T-handle screwdriverIS screws · FC44 TI24/1994 testing tools retain adapter and alternative requirements
- 5910 890 8210 — Crimping toolwire connectors/terminals · FC44 TI24/1994 testing tools retain adapter and alternative requirements
- 5910 893 8800 — Assembly hookfuel hose · FC44 TI24/1994 testing tools retain adapter and alternative requirements
- 0000 890 1710 — Testing tool kitcontains footnote 1 tools only · FC44 TI24/1994 testing tools retain adapter and alternative requirements
- 1110 141 8600 — Fuel linemandatory nipple adapter · FC44 TI24/1994 testing tools retain adapter and alternative requirements
- 0811 611 8200 — A10 pliersalternative to A19 · FC44 TI24/1994 testing tools retain adapter and alternative requirements
- 1114 893 4601 — Press sleevealternative to 4112 893 2401 · FC44 TI24/1994 testing tools retain adapter and alternative requirements
Service note · FC 44
FC 44: workshop times and split manual references
Engine procedures refer to FS36/40/44; deflector/gearhead procedures refer to EC70.
- Service procedures for FS36/40/44 brushcutter ENGINE and EC70 electric-edger DEFLECTOR/GEARHEAD can be used for FC44. This is subsystem-specific guidance, not whole-machine interchange or proof those manuals were imported/accepted.
- Historical minutes for trained staff in properly equipped workshop; asterisk means TEST RUN UNDER LOAD. Jobs 1–7:remove/install engine 20; pressure-test crankcase 130*; crankshaft/bearings/pressure test 130*; oil seals/pressure test 110*; check crankcase for leaks/test run 100; cylinder/piston/pressure test 120*; ignition system 110*. Unusually large printed pressure-test 130 retained, not silently changed to 13 or 30.
- Jobs 8–15:fuel supply/tank vent/test run 30; manifold or flange/pressure test 110; carburetor/test 45*; handle/throttle control 30; rewind starter/test run 20; clutch/test run 20; muffler 30; air filter 5.
- Jobs 16–22:stop switch/test run 20; clutch housing 20; drive tube 25; replace COMPLETE gearhead OR bearing housing 5; limit stop OR deflector 10; drive shaft 10; fuel tank 15. All 22 allowances retained. Asterisk under-load requirement applies only jobs 2, 3, 4, 6, 7, 10; not all jobs marked “test run”. These historical scheduling allowances are not measured repair durations or authority to energize hardware.
- Historical TI 24/1994 for FC44 only; shared-engine or design-principle comparisons are not universal loose-part interchange. No serial cutoff supplied. Source date November 10, 1994; referenced manuals are not whole-manual acceptance. Owner-manual precautions remain required. No physical interchange test was performed.
Source: TI 24/1994, p. 8 — workshop times and split manual references.
No additional parts-table entry added.
Wrong number or missing part for the FC 44? Report a correction →