Stihl 4130 · Section H · 8 of 9 · 28 parts
Drive tube assembly, Gear head, Loop handle
Fits FC 44.
Historical fitment & changes (2) — includes parts and conditions not shown on this drawing.
Parts (28)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4130 710 7117 | Drive tube assembly Ø 25.4 mm / 1'' | 1 |
| 2 | 0000 967 3653 | Warning pictogram FC | 1 |
| 3 | 4140 711 3202 | Drive shaft | 1 |
| 4 | 4133 717 2000 | Cap | 1 |
| 5 | 4133 641 0306 | Gear housing | 1 |
| 6 | 9503 003 9491 | Grooved ball bearing 629-2Z | 1 |
| 7 | not sold separately | Drive pinion not available as a separate item | 1 |
| 8 | not sold separately | Spur bevel gear not available as a separate item | 1 |
| 9 | 9503 003 9850 | Grooved ball bearing 609 → replaced by 9503 003 9853 TI 46/2000 | 1 |
| 10 | 9503 003 9853 | Grooved ball bearing 609-2Z | 1 |
| 11 | 9455 621 0750 | Circlip 9x1 | 1 |
| 12 | 9456 621 2660 | Circlip 24x1.2 | 1 |
| 13 | 4133 642 0600 | Drive shaft | 1 |
| 14 | 9503 003 6440 | Grooved ball bearing 6201-2RS → replaced by 9503 003 6420 TI 5/1994 | 1 |
| 15 | 9456 621 3600 | Circlip 32x1.2 | 1 |
| 16 | 4119 713 6500 | Screw plug | 1 |
| 17 | 9022 341 1300 | Spline screw IS-M6x20 | 1 |
| 18 | 4133 713 1500 | Thrust plate | 1 |
| 19 | 4133 717 2701 | Guard ring | 1 |
| 20 | 4133 642 7601 | Collar nut | 1 |
| 21 | 4130 790 1300 | Loop handle | 1 |
| 22 | 4130 791 2000 | Handle hose | 1 |
| 23 | 9075 478 4115 | Pan head self-tapping screw IS-D5x16 | 1 |
| 24 | 4130 791 6805 | Clamp | 1 |
| 25 | 9041 116 1430 | Pan head screw M6x50 | 1 |
| 26 | 9222 068 0900 | Square nut M6 | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 4133 640 0106 | Gearhead | 1 |
| — | 4133 640 7300 | Set of pinions | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · FC 44
FC 44: approved blade, left-hand shaft and deflector orientation
Only the listed 200 mm blade is approved in this TI; wheel-side changes require flap relocation.
- For safety reasons TI approves ONLY blade 4133 713 4101, 200 mm (8 in) long. Flexible drive shaft in curved tube transmits power to gearhead. Gearhead uses same design principle as FS66–106; output shaft as FC72 with M8 LEFT-HAND thread. These comparisons do not assign FC44 blade or gearhead to those models.
- Illustration identifies blade 7, shaft 8, thrust plate 9, thrust washer 10, nut 11. Place blade on thrust plate, then thrust washer over shaft, secure with nut. Nut has CAPTIVE SPRING WASHER; if it loses resilience, replace WHOLE NUT. No blade-nut tightening torque printed in this section or torque table; do not substitute the 21 Nm depth-wheel value.
- Deflector 12 rotates on gearhead to set depth: release clamp screw 13, rotate, retighten. Arrow on OPEN SIDE MUST FACE AWAY FROM OPERATOR so debris is diverted away from operator and machine. Cutting guide 14 indicates blade position; flexible flap 15 extends deflector and diverts debris.
- Depth wheel 16 supports part of weight and maintains depth; it may mount EITHER SIDE of deflector, but rubber flap position MUST THEN CHANGE to match. Diagram orientation does not override that explicit side-change condition.
- Historical TI 24/1994 for FC44 only; shared-engine or design-principle comparisons are not universal loose-part interchange. No serial cutoff supplied. Source date November 10, 1994; referenced manuals are not whole-manual acceptance. Owner-manual precautions remain required. No physical interchange test was performed.
Source: TI 24/1994, p. 2 · TI 24/1994, p. 3 · TI 24/1994, p. 4 — approved blade, left-hand shaft and deflector orientation.
Part numbers (1)
- 4133 713 4101 — 200 mm /8 in cutting bladeonly TI-approved blade · FC44 TI24/1994 approved blade, left-hand shaft and deflector orientation
Service note · FC 44
FC 44: component-specific tightening torques
Clutch drum 2.5 Nm differs from clutch 17 Nm; depth-wheel 21 Nm is not a blade-nut setting.
- Source Nm / lbf.ft pairs, with exact thread/joint association: captive spline IS8–32 inch, clutch drum to crankshaft 2.5/1.8; clutch 3/8–24 inch, clutch to crankshaft 17/12.5; B3.5×9.5, backing plate/diaphragm/diaphragm carrier AND frame on muffler 2/1.5; B3.9×19, control handle 2.5/1.8; IS-DG5×16, loop handle 2.5/1.8.
- IS-TT4.8×19: fan housing to spiral housing 3.0/2.2; diaphragm carrier to crankcase 4.5/3.3. IS-DG5×24: shroud to fan housing 3.5/2.6; clutch/starter housing to fan housing 3.5/2.6. IS-DG5×60: shroud/carburetor/diaphragm carrier 3.5/2.6; muffler to cylinder 6.5/4.8 (printed German “Schalldämpfer am Zylinder”).
- IS-M4×20, ignition module to cylinder 3.5/2.6; IS-M5×18, clamp on clutch housing 6.5/4.8; IS-M6×18, cylinder to crankcase 14.0/10.3; IS-TT5.2×14, spiral housing to crankcase 14.0/10.3; M6×50 pan-head, clamp screw in loop handle 3.5/2.6; IS-M11×10 screw plug, gearhead 10.0/7.5.
- M14×1.25 spark plug 19.0/14.0; P5×14 special spline, filter cover to shroud 2.5/1.8; IS-M6×20, gearhead clamp screw 7.5/5.5; IS-M6×25, clamp to deflector 7.5/5.5; M6 clamp screw, clamp on deflector 7.5/5.5; IS-DG5×12, clamp for clamp screw AND flap to deflector 5.5/4.0; M10 collar screw, depth wheel 21/15.5.
- All 24 numeric torque rows preserved. Inch-thread asterisks apply to IS8–32 and 3/8–24, not adhesive requirements. Table gives NO M8 BLADE-NUT torque. Do not transfer 21 Nm wheel or 17 Nm clutch setting to blade nut. Rounded imperial values retained as printed; no live tightening validation.
- Historical TI 24/1994 for FC44 only; shared-engine or design-principle comparisons are not universal loose-part interchange. No serial cutoff supplied. Source date November 10, 1994; referenced manuals are not whole-manual acceptance. Owner-manual precautions remain required. No physical interchange test was performed.
Source: TI 24/1994, p. 6 — component-specific tightening torques.
No additional parts-table entry added.
Wrong number or missing part for the FC 44? Report a correction →