← Edgers & other equipment · series 4130

Stihl 4130 · Section A · 1 of 14 · 26 parts

Crankcase, Cylinder

Fits FS 36, FS 40, FS 44.

Parts diagrams →

Historical fitment & changes (3) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
1101112131415161718192202122440414156789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (26)

PosPart numberDescriptionQty
1 4130 020 2105 Crankcase Fitment / change note → 1
2 9503 003 9955 Grooved ball bearing 0.5x1.125x0.312" 1
4 9633 003 9985 Oil seal 1
5 9503 003 9957 Grooved ball bearing 0.5x1.125x0.312" 1
6 9291 021 3932 Washer 23.1x12.8x0.9 1
7 4130 030 0400 Crankshaft 1
8 4130 036 8600 Woodruff key 1
9 4130 020 1200 Cylinder with piston Ø 35 mm 1
10 4130 030 2000 Piston with connecting rod 1
11 4130 034 3000 Piston ring 1
12 4130 029 2300 Cylinder gasket 1
13 9022 341 1310 Spline screw IS-M6x18 2
14 4130 084 1150 Spiral housing Fitment / change note → 1
15 4130 028 0205 Spline screw TT 5.2x14.3 Fitment / change note → 4
16 4130 029 0500 Gasket 1
17 4130 020 0500 Diaphragm carrier 1
18 4130 141 4100 Diaphragm 1
19 4130 141 2400 Support plate 1
20 9099 021 2360 Self-tapping screw 3.5x9.5 1
21 4130 028 0200 Spline screw TT 4.8x19 Fitment / change note → 4
22 4112 400 7001 Spark plug NGK BMR 6A 1
22 0000 400 7002 NLA Spark plug AC CSR 45 1
40 9022 341 1260 Spline screw IS-M6x12 Fitment / change note → 4
41 9456 621 3255 Circlip Fitment / change note → 2
Not numbered on the diagram — assemblies, kits and options
— 4130 020 0205 Engine Fitment / change note → 1
— 4130 007 1050 Set of gaskets 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · FS 36 / FS 40 / FS 44

FS 36 / 40 / 44: TT screw torque depends on mounting point

Modified core holes require supplied TT screws; one screw number has two different torques.

X 28 222 807 — Printed introduction for this component only; not a universal machine cutoff or interchange guarantee.

  • From X 28 222 807, thread-forming TT screws secure the spiral housing, fan housing and diaphragm carrier. Rounded-triangular shank displaces light-alloy material and temporarily deforms the bore to resist loosening. Source says screws may be released and retightened repeatedly without loss of joint strength; this is not permission to use damaged threads or omit torque control.
  • Core holes in replacement crankcase and spiral housing are modified for TT screws, which are supplied with them and MUST be used for the listed joints. Always tighten with a TORQUE WRENCH: IS-TT 4.8×19 screw 4130 028 0200 is 3.0 Nm (2.2 lbf.ft) for FAN housing to SPIRAL housing, but 4.5 Nm (3.3 lbf.ft) for DIAPHRAGM CARRIER to CRANKCASE. IS-TT 5.2×14 screw 4130 028 0205 is 14.0 Nm (10.3 lbf.ft) for SPIRAL housing to CRANKCASE. Do not choose torque by screw number alone.
  • Engine 4130 020 0200 changes to 4130 020 0205, including items 1–4. Crankcase 4130 020 2100 changes to 4130 020 2105 (item 1), including TT screw items 2 and 3; spiral housing 4130 084 1100 changes to 4130 084 1150 (item 4), including item 2. These original assemblies are no longer factory-available.
  • Table lists four IS-TT 4.8×19 and four IS-TT 5.2×14 screws. Original IS-DG 5×16 screw 9075 478 4115 and IS-M6×12 screw 9022 341 1260 remain available for OTHER models. No general old-hole/new-screw interchange is stated. Ringless crankcase introduction is separately in progress; do not assign the TT cutoff to it.
  • Source identifier/header is TI17.94, retained as 1994-17, but the original footer says March 10, 1995 and copyright 1995. Preserve that discrepancy; do not silently change source year or equate publication and review dates.
  • Historical TI 17/1994 guidance for the explicitly named models only; no successor or unlisted variant applicability inferred. Factory supply statements are historical, not current stock claims. MOQ columns are order quantities, not fitting quantities. No physical interchange test was performed.

Source: TI 17/1994, p. 1 · TI 17/1994, p. 2 · TI 17/1994, p. 3 — FS 36 / 40 / 44: TT screw torque depends on mounting point.

Part numbers (10)
  • 4130 028 0200 — IS-TT 4.8×19 screw, item 23.0 or 4.5 Nm by mounting point · FS 36 / 40 / 44: TT screw torque depends on mounting point
  • 4130 028 0205 — IS-TT 5.2×14 screw, item 314.0 Nm spiral housing joint · FS 36 / 40 / 44: TT screw torque depends on mounting point
  • 4130 020 0200 — Original engineno longer factory-available · FS 36 / 40 / 44: TT screw torque depends on mounting point
  • 4130 020 0205 — Revised engine, items 1–4new · FS 36 / 40 / 44: TT screw torque depends on mounting point
  • 4130 020 2100 — Original crankcaseno longer factory-available · FS 36 / 40 / 44: TT screw torque depends on mounting point
  • 4130 020 2105 — Revised crankcase, item 1includes TT screws · FS 36 / 40 / 44: TT screw torque depends on mounting point
  • 4130 084 1100 — Original spiral housingno longer factory-available · FS 36 / 40 / 44: TT screw torque depends on mounting point
  • 4130 084 1150 — Revised spiral housing, item 4includes item 2 · FS 36 / 40 / 44: TT screw torque depends on mounting point
  • 9075 478 4115 — Original IS-DG 5×16 screwretained for other models · FS 36 / 40 / 44: TT screw torque depends on mounting point
  • 9022 341 1260 — Original IS-M6×12 screwretained for other models · FS 36 / 40 / 44: TT screw torque depends on mounting point

Service note · FS 36 / FS 40 / FS 44

FS 36 / 40 / 44: ringless crankcase needs dimension-controlled bearing assembly

New crankcase omits retaining-ring grooves; old rings remain spares for original applications.

  • Crankshaft bearings are now installed without the retaining rings formerly used as axial stops; revised crankcase has NO grooves for those rings. Original two retaining rings 9456 621 3255 remain available as spares, not as parts to add to the groove-free case. Section 1.2 introduction is in progress, with no serial; X 28 222 807 belongs to section 1.1 TT screws.
  • For this LATEST crankcase version: slip washer (1) onto crankshaft; push bearing (2) OPEN SIDE FIRST over the shaft against the crank web; heat crankcase to approximately 100°C (210°F); press crankshaft into case until dimension a = 34 ± 0.2 mm (printed 1.34 ± 0.01 in). Use the dimension-a datums shown in source drawing 342TI004, not an invented reference surface.
  • Using a press sleeve, press oil seal (3) SEALING LIP FIRST about 20 mm (0.8 in) into the case. Press bearing (4) CLOSED SIDE FIRST until flush with the top of the case. Then CHECK dimension a and correct if necessary. These are different orientation requirements for the two bearings; no bearing number, sleeve number or press force is supplied.
  • This preserves the TI service sequence, not a claim that the complete service manual or a real repair has been validated. The approximate depth and metric/inch rounded values remain as printed.
  • Source identifier/header is TI17.94, retained as 1994-17, but the original footer says March 10, 1995 and copyright 1995. Preserve that discrepancy; do not silently change source year or equate publication and review dates.
  • Historical TI 17/1994 guidance for the explicitly named models only; no successor or unlisted variant applicability inferred. Factory supply statements are historical, not current stock claims. MOQ columns are order quantities, not fitting quantities. No physical interchange test was performed.

Source: TI 17/1994, p. 2 · TI 17/1994, p. 3 — FS 36 / 40 / 44: ringless crankcase needs dimension-controlled bearing assembly.

Part numbers (2)
  • 9456 621 3255 — Original crankcase retaining rings, tworemain spare; not installed in groove-free case · FS 36 / 40 / 44: ringless crankcase needs dimension-controlled bearing assembly
  • 4130 020 2105 — Revised crankcaseringless assembly procedure · FS 36 / 40 / 44: ringless crankcase needs dimension-controlled bearing assembly

Service note · FS 36 / FS 40 / FS 44

FS 36 / 40 / 44: larger-filter pickup changes at X 28 903 005

Pickup 0000 350 3502 replaces 1120 350 3500 for the stated models.

X 28 903 005 — Printed introduction for this component only; not a universal machine cutoff or interchange guarantee.

  • From X 28 903 005, pickup 0000 350 3502 replaces 1120 350 3500 with a larger filter area; source claims longer life and improved dirt retention. Original pickup is no longer factory-available. Standardization with other models does not identify their fitment.
  • This is 0000 350 3502, NOT the 0000 350 3500 pickup in other TIs. Neither an S-shaped hose requirement nor universal interchange across those other applications is stated here.
  • Source identifier/header is TI17.94, retained as 1994-17, but the original footer says March 10, 1995 and copyright 1995. Preserve that discrepancy; do not silently change source year or equate publication and review dates.
  • Historical TI 17/1994 guidance for the explicitly named models only; no successor or unlisted variant applicability inferred. Factory supply statements are historical, not current stock claims. MOQ columns are order quantities, not fitting quantities. No physical interchange test was performed.

Source: TI 17/1994, p. 4 · TI 17/1994, p. 5 — FS 36 / 40 / 44: larger-filter pickup changes at X 28 903 005.

Part numbers (2)
  • 1120 350 3500 — Original fuel pickup bodyno longer factory-available · FS 36 / 40 / 44: larger-filter pickup changes at X 28 903 005
  • 0000 350 3502 — Larger-filter fuel pickup bodynew · FS 36 / 40 / 44: larger-filter pickup changes at X 28 903 005

Wrong number or missing part for the FS 36, FS 40, FS 44? Report a correction →