Stihl 4130 · Section B · 2 of 14 · 39 parts
Ignition system, Rewind starter
Fits FS 36, FS 40, FS 44.
Historical fitment & changes (10) — includes parts and conditions not shown on this drawing.
Parts (39)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4130 400 1250 | Flywheel Fitment / change note → | 1 |
| 2 | 4130 998 1400 | Torsion spring | 2 |
| 3 | 4130 195 7200 | Pawl | 2 |
| 4 | 1114 195 7800 | Pin | 2 |
| 5 | 0000 958 0924 | Washer Fitment / change note → | 1 |
| 6 | 4130 400 1300 | Ignition module Fitment / change note → | 1 |
| 7 | 1130 405 1000 | Spark plug boot | 1 |
| 8 | 0000 998 0614 | Torsion spring | 1 |
| 9 | 9291 021 0100 | Washer 4.3 | 2 |
| 10 | 9022 371 0710 | Spline screw IS-M4x20 | 2 |
| 11 | 4130 442 1601 | Contact spring | 1 |
| 12 | 4130 084 1002 | Fan housing | 1 |
| 13 | 4130 195 0700 | Rewind starter housing | 1 |
| 14 | 9075 478 4155 | Pan head self-tapping screw IS-D5x24 | 4 |
| 15 | 4130 084 9100 | Bushing | 1 |
| 16 | 4130 195 1600 | Rewind spring | 1 |
| 17 | 4130 195 0400 | Rope rotor | 1 |
| 18 | 0000 958 1804 | Washer | 1 |
| 19 | 9455 621 1670 | Circlip 16x1 | 1 |
| 20 | 4130 195 3400 | Starter grip | 1 |
| 21 | 4130 195 8200 | Starter rope Ø 3.5x850 mm | 1 |
| 22 | 0000 190 3400 | Starter grip ElastoStart Ø 3 mm Fitment / change note → → replaced by 0000 190 3403, 0000 190 3403 TI 42/1999 option | 1 |
| 23 | 0000 195 8200 | Starter rope Ø 3x800 mm Fitment / change note → option | 1 |
| 24 | 0000 195 7000 | Cap option | 1 |
| 25 | 4130 430 2000 | Slide | 1 |
| 26 | 4130 028 0200 | Spline screw TT 4.8x19 Fitment / change note → | 4 |
| 28 | 0751 030 8454 | Spade terminal no longer available from factory | 1 |
| 29 | 0751 030 8404 | Terminal socket 6.3-1 no longer available from factory | 1 |
| 30 | 0751 030 8471 | Grommet no longer available from factory | 1 |
| 31 | not sold separately | Hose 130 mm / 5 1/8'' | 1 |
| 32 | 4130 182 2100 | Support | 1 |
| 33 | 4119 431 6700 | Terminal socket no longer available from factory | 1 |
| 34 | 0000 967 3693 | Warning pictogram Filler cap | 1 |
| 40 | 4130 440 1100 | Short circuit wire 660 mm / 26'' | 1 |
| 41 | not sold separately | Hose 220 mm / 8 11/16'' | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 4130 007 1028 | Rewind starter kit | 1 |
| — | 0000 930 2203 | Starter rope Ø 3.5 mm x 30.5 m not illustratedoption | 1 |
| — | 0000 930 2208 NLA | Starter rope Ø 3 mm x 30.5 m not illustratedoption | 1 |
| — | 4203 711 7201 | Hose 960 mm / 37 13/16'' | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Historical fitment · FS 36 / FS 40 / FS 44 / FC 44
FS 36 / FS 40 / FS 44 / FC 44: series 4130 replacement ignition assignment
4130 400 1300 with flywheel 4130 400 1250; ignition lead not replaceable.
- Printed series 4130. Use 4130 400 1300 with flywheel 4130 400 1250.
- The asterisk means ignition lead not replaceable; it is not a zero or unspecified cut length.
- TI01/1999 lists replacement combinations for the then-current machines, not every earlier configuration. Older machines are referred to Spare Parts for Previous Models in their own illustrated parts lists; no serial cutoff is supplied here.
- Use only the listed ignition-module/flywheel combinations. The source warns that incorrect combinations can cause excessive RPM or running in reverse; sharing a module number does not make all flywheels interchangeable.
- Universal replacement modules may differ from production modules in maker, shape and part number. The source describes installation/function compatibility within its assignments, not universal compatibility or a project hardware test.
- Some replacement modules require shortening the ignition lead and/or short-circuit wire and crimping a different short-circuit connector. The table gives ignition-lead lengths only; it supplies neither a short-circuit-wire length nor a connector part number. Do not infer that every row needs modification.
- Only the named models and printed series are covered. A shared IPL sheet does not extend this assignment to unnamed models or modern MS equivalents. This 1999 USA bulletin is historical guidance, not current availability.
- The bulletin prints series 4130; the retained exact-model ignition sheets are cataloged under 4130, 4144. This link is an exact model-label navigation aid, not proof that the printed series identifiers are equivalent. Verify the actual machine configuration.
Source: TI 1/1999, p. 1 · TI 1/1999, p. 3 — 1.1 general restrictions and 1.2.2 power-tool assignments.
Part numbers (2)
- 4130 400 1300 — Replacement ignition moduleAssigned component · FS 36 / FS 40 / FS 44 / FC 44, printed series 4130, listed combination only
- 4130 400 1250 — Assigned flywheelRequired pairing · FS 36 / FS 40 / FS 44 / FC 44, printed series 4130
Service note · FS 36 / FS 40 / FS 44
FS 36 / 40 / 44: TT screw torque depends on mounting point
Modified core holes require supplied TT screws; one screw number has two different torques.
X 28 222 807 — Printed introduction for this component only; not a universal machine cutoff or interchange guarantee.
- From X 28 222 807, thread-forming TT screws secure the spiral housing, fan housing and diaphragm carrier. Rounded-triangular shank displaces light-alloy material and temporarily deforms the bore to resist loosening. Source says screws may be released and retightened repeatedly without loss of joint strength; this is not permission to use damaged threads or omit torque control.
- Core holes in replacement crankcase and spiral housing are modified for TT screws, which are supplied with them and MUST be used for the listed joints. Always tighten with a TORQUE WRENCH: IS-TT 4.8×19 screw 4130 028 0200 is 3.0 Nm (2.2 lbf.ft) for FAN housing to SPIRAL housing, but 4.5 Nm (3.3 lbf.ft) for DIAPHRAGM CARRIER to CRANKCASE. IS-TT 5.2×14 screw 4130 028 0205 is 14.0 Nm (10.3 lbf.ft) for SPIRAL housing to CRANKCASE. Do not choose torque by screw number alone.
- Engine 4130 020 0200 changes to 4130 020 0205, including items 1–4. Crankcase 4130 020 2100 changes to 4130 020 2105 (item 1), including TT screw items 2 and 3; spiral housing 4130 084 1100 changes to 4130 084 1150 (item 4), including item 2. These original assemblies are no longer factory-available.
- Table lists four IS-TT 4.8×19 and four IS-TT 5.2×14 screws. Original IS-DG 5×16 screw 9075 478 4115 and IS-M6×12 screw 9022 341 1260 remain available for OTHER models. No general old-hole/new-screw interchange is stated. Ringless crankcase introduction is separately in progress; do not assign the TT cutoff to it.
- Source identifier/header is TI17.94, retained as 1994-17, but the original footer says March 10, 1995 and copyright 1995. Preserve that discrepancy; do not silently change source year or equate publication and review dates.
- Historical TI 17/1994 guidance for the explicitly named models only; no successor or unlisted variant applicability inferred. Factory supply statements are historical, not current stock claims. MOQ columns are order quantities, not fitting quantities. No physical interchange test was performed.
Source: TI 17/1994, p. 1 · TI 17/1994, p. 2 · TI 17/1994, p. 3 — FS 36 / 40 / 44: TT screw torque depends on mounting point.
Part numbers (10)
- 4130 028 0200 — IS-TT 4.8×19 screw, item 23.0 or 4.5 Nm by mounting point · FS 36 / 40 / 44: TT screw torque depends on mounting point
- 4130 028 0205 — IS-TT 5.2×14 screw, item 314.0 Nm spiral housing joint · FS 36 / 40 / 44: TT screw torque depends on mounting point
- 4130 020 0200 — Original engineno longer factory-available · FS 36 / 40 / 44: TT screw torque depends on mounting point
- 4130 020 0205 — Revised engine, items 1–4new · FS 36 / 40 / 44: TT screw torque depends on mounting point
- 4130 020 2100 — Original crankcaseno longer factory-available · FS 36 / 40 / 44: TT screw torque depends on mounting point
- 4130 020 2105 — Revised crankcase, item 1includes TT screws · FS 36 / 40 / 44: TT screw torque depends on mounting point
- 4130 084 1100 — Original spiral housingno longer factory-available · FS 36 / 40 / 44: TT screw torque depends on mounting point
- 4130 084 1150 — Revised spiral housing, item 4includes item 2 · FS 36 / 40 / 44: TT screw torque depends on mounting point
- 9075 478 4115 — Original IS-DG 5×16 screwretained for other models · FS 36 / 40 / 44: TT screw torque depends on mounting point
- 9022 341 1260 — Original IS-M6×12 screwretained for other models · FS 36 / 40 / 44: TT screw torque depends on mounting point
Service note · FS 36 / FS 40 / FS 44
FS 36 / 40 / 44: modified flywheel requires the supplied washer
Washer goes between flywheel and spacer sleeve; also recommended for the original flywheel.
- Modified mounting-hole flywheel 4130 400 1250 replaces 4130 400 1200 and is supplied ONLY with washer 0000 958 0924 to ensure interchangeability with original machine versions. Install new flywheel ONLY together with that washer, positioned BETWEEN flywheel (1) and spacer sleeve (3); washer is drawing item 2.
- The same washer is RECOMMENDED when installing the original flywheel, which remains factory-supplied only while stocks last. Distinguish mandatory new-flywheel pairing from the recommendation for the old one. Introduction in progress, no serial or flywheel torque supplied.
- Source identifier/header is TI17.94, retained as 1994-17, but the original footer says March 10, 1995 and copyright 1995. Preserve that discrepancy; do not silently change source year or equate publication and review dates.
- Historical TI 17/1994 guidance for the explicitly named models only; no successor or unlisted variant applicability inferred. Factory supply statements are historical, not current stock claims. MOQ columns are order quantities, not fitting quantities. No physical interchange test was performed.
Source: TI 17/1994, p. 3 · TI 17/1994, p. 4 — FS 36 / 40 / 44: modified flywheel requires the supplied washer.
Part numbers (3)
- 4130 400 1200 — Original flywheelwhile stocks last; washer recommended · FS 36 / 40 / 44: modified flywheel requires the supplied washer
- 4130 400 1250 — Modified flywheel including washerwasher mandatory · FS 36 / 40 / 44: modified flywheel requires the supplied washer
- 0000 958 0924 — Washer, item 2between flywheel and spacer sleeve · FS 36 / 40 / 44: modified flywheel requires the supplied washer
Service note · FS 36 / FS 40 / FS 44
FS 36 / 40 / 44: NGK and Champion plugs need their gaps increased
Printed 0.5–0.6 mm is not the final installation gap for the two replacement plugs.
- Production GM AC CSR 45 will be replaced in the near future by Champion RCJ8. Listed replacements: GM AC CSR 45 (General Motors) 0000 400 7002 at 0.7–0.8 mm; NGK BMR 6 A 4112 400 7001 and Champion RCJ8 0000 400 7005 each printed at 0.5–0.6 mm WITH remark 1.
- Remark 1 requires INCREASING NGK and Champion electrode gaps to 0.7–0.8 mm (0.028–0.030 in) BEFORE INSTALLATION. Do not present the smaller supplied/table gaps as final service settings. GM plug remains listed as a replacement; the production change is not universal withdrawal of that plug.
- No numeric serial is given. All three part/type/manufacturer mappings remain distinct; no later spark-plug successor is inferred.
- Source identifier/header is TI17.94, retained as 1994-17, but the original footer says March 10, 1995 and copyright 1995. Preserve that discrepancy; do not silently change source year or equate publication and review dates.
- Historical TI 17/1994 guidance for the explicitly named models only; no successor or unlisted variant applicability inferred. Factory supply statements are historical, not current stock claims. MOQ columns are order quantities, not fitting quantities. No physical interchange test was performed.
Source: TI 17/1994, p. 4 — FS 36 / 40 / 44: NGK and Champion plugs need their gaps increased.
Part numbers (3)
- 0000 400 7002 — GM AC CSR 45 spark plug, General Motorslisted replacement; 0.7–0.8 mm · FS 36 / 40 / 44: NGK and Champion plugs need their gaps increased
- 4112 400 7001 — NGK BMR 6 A spark plugincrease gap before installation · FS 36 / 40 / 44: NGK and Champion plugs need their gaps increased
- 0000 400 7005 — Champion RCJ8 spark plugincrease gap before installation · FS 36 / 40 / 44: NGK and Champion plugs need their gaps increased
Historical fitment · FC 44 / FS 36 / FS 40 / FS 44
FC 44 / FS 36 / FS 40 / FS 44: ElastoStart special-accessory retrofit
0000 190 3400 includes required 3 x 800 mm rope 0000 195 8200.
- The new ElastoStart is offered with immediate effect as a SPECIAL ACCESSORY, not stated standard production equipment. No changes to the rewind starter are necessary to retrofit it, but installation differs slightly from the standard grip. No serial cutoff or verified production date is supplied.
- The page 3 spare table lists complete ElastoStart 0000 190 3400 INCLUDING item 1, starter rope 0000 195 8200, dimension 3 x 800 mm. Item 1 here is a spare-table position, not construction drawing item 1 (grip). No separate internal component ordering numbers or additional quantity claims are printed.
- Printed model-series assignment: FC 44 and FS 36/40/44 — 4130.
- Historical TI 07/1996 guidance for BG 72, FC 44, FC 72, FS 36, FS 40, FS 44, FS 72, FS 74 and FS 76 only. No later variant, chainsaw or other shared-sheet model is included. No hardware operation was performed; availability and comfort claims are historical, not current stock or a measured project result.
Source: TI 7/1996, p. 1 · TI 7/1996, p. 3 — FC 44 / FS 36 / FS 40 / FS 44: ElastoStart special-accessory retrofit.
Part numbers (2)
- 0000 190 3400 — ElastoStart complete assemblyincludes item 1 starter rope · FC 44, FS 36, FS 40, FS 44; TI07/1996 ElastoStart only
- 0000 195 8200 — Starter rope 3 x 800 mmrequired rope; included item 1 · FC 44, FS 36, FS 40, FS 44; TI07/1996 ElastoStart only
Service note · BG 72 / FC 44 / FS 36 / FS 40 / FS 44 / FC 72 / FS 72 / FS 74 / FS 76
ElastoStart construction and force path: spring-label conflict retained
Spring cushioning is qualitative; the function paragraph calls the spring (3), but the key and drawing use (4).
- Construction key: 1 grip, 2 cap, 3 sleeve, 4 helical spring, 5 washer, 6 starter rope. The drawing shows upper and lower washers both labeled 5. In the relaxed position the sleeve, spring and washers are retained by stop lug 7. These are component labels, not independently supplied spare numbers.
- During cranking the described load path is grip 1 → lower washer 5 → helical spring → upper washer 5 → sleeve 3 → rope 6. Engine compression compresses the spring and its peaks are cushioned. The printed function paragraph says helical spring (3), although its opening paragraph, page 1 key and both drawings assign spring 4 and sleeve 3. This source contradiction remains explicit; the immutable text is not rewritten.
- After the first compression stroke the source describes grip force as practically uniform. Above an unspecified spring-determined starting-force level the spring becomes fully compressed and effort transfers directly from grip to rope. No force threshold, spring rate, travel limit or replacement spring specification is given.
- Page 1 plots tensile force versus hand travel, with thick ElastoStart and thin standard-grip curves. Axes have no numerical values; the illustration is qualitative and does not establish a percentage reduction. Construction differs from the chainsaw version referenced in TI 29/1992; that TI is outside the retained inventory. No missing chainsaw construction or interchange claim is imported; current construction is fully described here.
- The TI header prints BG 72 as series 4227, while the retained exact-model BG 72 rewind-starter IPL is cataloged under 4133 (4227 has BG 75). The BG 72 link is exact-model navigation only: this unresolved series conflict is not silently corrected and does not establish BG 75 fitment or equivalence of series.
- Historical TI 07/1996 guidance for BG 72, FC 44, FC 72, FS 36, FS 40, FS 44, FS 72, FS 74 and FS 76 only. No later variant, chainsaw or other shared-sheet model is included. No hardware operation was performed; availability and comfort claims are historical, not current stock or a measured project result.
Source: TI 7/1996, p. 1 · TI 7/1996, p. 2 — ElastoStart construction and force path: spring-label conflict retained.
No additional parts-table entry added.
Service note · BG 72 / FC 44 / FS 36 / FS 40 / FS 44 / FC 72 / FS 72 / FS 74 / FS 76
ElastoStart repair limit: rope only, otherwise complete assembly
The cutaway is not permission to repair the grip internals.
- Repairs are LIMITED TO REPLACEMENT OF THE STARTER ROPE. A faulty ElastoStart can only be replaced as a COMPLETE ASSEMBLY. The cutaway and named spring/sleeve/washers explain function, not approved internal repair or separately available components.
- For this accessory the complete assembly is 0000 190 3400 and the only separately listed replacement is rope 0000 195 8200. No spring substitute, preload setting or procedure to rebuild the grip is supplied.
- The TI header prints BG 72 as series 4227, while the retained exact-model BG 72 rewind-starter IPL is cataloged under 4133 (4227 has BG 75). The BG 72 link is exact-model navigation only: this unresolved series conflict is not silently corrected and does not establish BG 75 fitment or equivalence of series.
- Historical TI 07/1996 guidance for BG 72, FC 44, FC 72, FS 36, FS 40, FS 44, FS 72, FS 74 and FS 76 only. No later variant, chainsaw or other shared-sheet model is included. No hardware operation was performed; availability and comfort claims are historical, not current stock or a measured project result.
Source: TI 7/1996, p. 1 · TI 7/1996, p. 2 · TI 7/1996, p. 3 — ElastoStart repair limit: rope only, otherwise complete assembly.
Part numbers (2)
- 0000 190 3400 — ElastoStart complete assemblyincludes item 1 starter rope · BG 72, FC 44, FS 36, FS 40, FS 44, FC 72, FS 72, FS 74, FS 76; TI07/1996 ElastoStart only
- 0000 195 8200 — Starter rope 3 x 800 mmrequired rope; included item 1 · BG 72, FC 44, FS 36, FS 40, FS 44, FC 72, FS 72, FS 74, FS 76; TI07/1996 ElastoStart only
Service note · BG 72 / FC 44 / FS 36 / FS 40 / FS 44 / FC 72 / FS 72 / FS 74 / FS 76
ElastoStart installation: outside-in guide threading and rotor knot
The two installation steps require a simple overhand knot at the rope rotor.
- For installing ElastoStart WITH STARTER ROPE: thread the rope through the rope-guide bushing FROM OUTSIDE the starter housing. Then thread the rope into the rope rotor and secure it with a SIMPLE OVERHAND knot. Page 2 shows the guide/rotor route and knot; it does not prescribe a different multi-loop knot.
- These are accessory-specific installation changes, not a complete rewind-starter overhaul. No rotor pretension turn count, fastener torque or universal winding direction is printed; none is inferred from the arrow or from another model. The separate page 3 grip knot applies when replacing the rope.
- The TI header prints BG 72 as series 4227, while the retained exact-model BG 72 rewind-starter IPL is cataloged under 4133 (4227 has BG 75). The BG 72 link is exact-model navigation only: this unresolved series conflict is not silently corrected and does not establish BG 75 fitment or equivalence of series.
- Historical TI 07/1996 guidance for BG 72, FC 44, FC 72, FS 36, FS 40, FS 44, FS 72, FS 74 and FS 76 only. No later variant, chainsaw or other shared-sheet model is included. No hardware operation was performed; availability and comfort claims are historical, not current stock or a measured project result.
Source: TI 7/1996, p. 1 · TI 7/1996, p. 2 · TI 7/1996, p. 3 — ElastoStart installation: outside-in guide threading and rotor knot.
Part numbers (1)
- 0000 195 8200 — Starter rope 3 x 800 mmrequired rope; included item 1 · BG 72, FC 44, FS 36, FS 40, FS 44, FC 72, FS 72, FS 74, FS 76; TI07/1996 ElastoStart only
Service note · BG 72 / FC 44 / FS 36 / FS 40 / FS 44 / FC 72 / FS 72 / FS 74 / FS 76
ElastoStart rope replacement: mandatory 8200 rope and grip knot
Ease off cap, remove old rope, fit 0000 195 8200 with simple overhand grip knot, refit cap.
- Four printed steps: ease the cap off the starter grip; remove remaining rope from grip AND rope rotor; fit starter rope 0000 195 8200 in the same way as the standard rope, but secure it IN THE GRIP only with a SIMPLE OVERHAND knot; refit the cap in the grip. The drawing shows cap removal and rope/knot insertion into the grip.
- The source says rope 0000 195 8200 MUST be used to guarantee correct ElastoStart operation; its listed dimension is 3 x 800 mm. Matching diameter/length alone is not evidence that a substitute rope is approved. Page 2 separately requires a simple overhand knot at the rotor.
- The same-as-standard instruction refers to the base starter operation; this note preserves the complete accessory-specific delta, not a standalone base-starter repair manual. No extra winding count, trimming allowance or rope material specification is invented.
- The TI header prints BG 72 as series 4227, while the retained exact-model BG 72 rewind-starter IPL is cataloged under 4133 (4227 has BG 75). The BG 72 link is exact-model navigation only: this unresolved series conflict is not silently corrected and does not establish BG 75 fitment or equivalence of series.
- Historical TI 07/1996 guidance for BG 72, FC 44, FC 72, FS 36, FS 40, FS 44, FS 72, FS 74 and FS 76 only. No later variant, chainsaw or other shared-sheet model is included. No hardware operation was performed; availability and comfort claims are historical, not current stock or a measured project result.
Source: TI 7/1996, p. 2 · TI 7/1996, p. 3 — ElastoStart rope replacement: mandatory 8200 rope and grip knot.
Part numbers (1)
- 0000 195 8200 — Starter rope 3 x 800 mmrequired rope; included item 1 · BG 72, FC 44, FS 36, FS 40, FS 44, FC 72, FS 72, FS 74, FS 76; TI07/1996 ElastoStart only
Historical fitment · FS 36 / FS 40 / FS 44
FS 36/FS 40/FS 44: conditional tank mounting-hole enlargement
Old tank in modified fan housing: 7.5 mm holes; numbers stay unchanged.
- Modified fan housing has an integrally molded sleeve on each common mounting boss; modified tank has correspondingly larger mounting holes. Drawing 342TI008 arrows identify the bosses, not fuel-hose grommet holes.
- ONLY when fitting an unmodified tank into a modified fan housing, the tank MOUNTING holes must be drilled to 7.5 mm (19/64 in.). This is conditional compatibility, not unrestricted interchangeability or an instruction to enlarge fuel-hose holes.
- Both tank changes and the fan-housing change retain their part numbers despite limited interchangeability. The TI supplies no fan-housing part number. Do not treat current IPL fan housing 4130 084 1002 as a newly introduced number.
- Each modified fan housing is to include separate tank-upgrade instructions. That exact insert is not established in the bounded available manual-cover and document-filename inventory; the TI supplies the diameter and condition but not a complete insert. No drill setup or further procedure fabricated.
- Historical TI19/1996 evidence only; no calendar introduction date or current stock status inferred. FS 44 gearhead changes do not apply to FS 36/40 or FC 44. No hardware operation was performed.
Source: TI 19/1996, p. 1 · TI 19/1996, p. 2 — conditional tank mounting-hole enlargement.
Part numbers (1)
- 4130 350 0416 — Fuel tankUnchanged number; inspect mounting configuration · FS 36/40/44
Wrong number or missing part for the FS 36, FS 40, FS 44? Report a correction →