Stihl 4130 · Section B · 2 of 2 · 16 parts
Deflector, Bearing housing
Fits FSB-KM.
Historical fitment & changes (7) — includes parts and conditions not shown on this drawing.
Parts (16)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4130 713 4501 | Deflector | 1 |
| 2 | 4130 713 4100 | Blade | 1 |
| 3 | 9074 478 4405 | Pan head self-tapping screw IS-P6x14 | 1 |
| 4 | 9771 021 2760 | Hose clip Ø 1 7/8x1/2" | 1 |
| 5 | 4130 640 1405 | Bearing housing | 1 |
| 6 | 9513 003 3210 | Needle cage 12x16x10 | 2 |
| 7 | 0000 958 1233 | Washer | 2 |
| 8 | 9455 621 1130 | Circlip 12x1 | 1 |
| 9 | 4130 640 2205 | Drive shaft | 1 |
| 10 | 9099 021 2360 | Self-tapping screw 3.5x9.5 | 1 |
| 11 | 4130 710 6701 | Hose clamp | 1 |
| 12 | 9022 341 1010 | Spline screw IS-M5x18 | 1 |
| 13 | 9210 260 0700 | Hexagon nut M5 | 1 |
| 14 | 4130 713 1501 | Thrust plate Fitment / change note → option | 1 |
| 15 | 4130 893 7800 | Locking pin Fitment / change note → option | 1 |
| 16 | 0781 120 1110 | Gear lubricant 225 g Fitment / change note → option | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · FSB-KM
FSB-KM: curved-tube identity and historical engine approvals
Only the explicitly listed powerheads are approved by this TI.
- The cover names FSB-KM, series 4137, with a curved drive tube, low weight and small FS 75-derived deflector for mowing-head trimming in hard-to-reach areas. The retained exact-model FSB-KM IPL is filed under series 4130. Both labels are preserved: an exact model-name match permits navigation but does NOT prove the two series codes equivalent.
- Section 2 permits ONLY KM 55 R, KM 85 R, KM 90 R and KM 110 R KombiEngines, plus split-drive-tube FS 55 RT, FS 83 RT and FS 85 RT brushcutters. No other KombiEngine combination is permitted by this source. The cover’s general T-model wording is constrained by this explicit list; it is not approval for every split-shaft machine.
- The cover photograph identifies the curved-tube tool, not a dimensioned drawing or proof that every FS 75 component interchanges.
- Historical English-USA 2007 source, not present-day stock or approval for unlisted variants. No numeric serial cutoff is supplied. No physical interchange test was performed.
Source: TI 52/2007, p. 1 · TI 52/2007, p. 2 — FSB-KM: curved-tube identity and historical engine approvals.
No additional parts-table entry added.
Service note · FSB-KM
FSB-KM: 12 mm shaft and two approved mowing heads
Metal cutting tools are expressly not approved.
- Figure 392TI053 marks A as the OUTPUT-SHAFT THREAD DIAMETER, 12 mm. The text names series 4004 mowing heads as also used on FS 75. Thread pitch is not printed; diameter alone does not approve all heads.
- The explicit approved list is AutoCut 11-2 mowing head 4004 710 2192 and PolyCut 5-3 mowing head 4004 710 2180. METAL CUTTING TOOLS ARE NOT APPROVED.
- Both listed heads require the APPROVED DEFLECTOR; the source refers to the Cutting Tools and Accessories for Brushcutters catalog for that selection. No deflector order number is printed here; the adjacent blade illustration does not authorize an arbitrary guard.
- Historical English-USA 2007 source, not present-day stock or approval for unlisted variants. No numeric serial cutoff is supplied. No physical interchange test was performed.
Source: TI 52/2007, p. 2 — FSB-KM: 12 mm shaft and two approved mowing heads.
Part numbers (2)
- 4004 710 2192 — AutoCut 11-2Approved with approved deflector · FSB-KM; source restrictions apply
- 4004 710 2180 — PolyCut 5-3Approved with approved deflector · FSB-KM; source restrictions apply
Service note · FSB-KM
FSB-KM: line-limiting blade and keyed deflector assembly
The tube bead, deflector recess and locking screw are separate locating features.
- Section 4.1.1, figure 002TI035: slide line-limiting blade (1) into the deflector guide, then insert/tighten screw (2) with combination wrench (3) or Allen key (4); the tool is supplied with the KombiEngine or available as a special accessory. No tightening torque is printed.
- Figure 002TI036: position one side of clamp (1) over deflector lug (2) and hold it, then slide the other clamp side over the deflector.
- Figure 002TI045: fit deflector (3) to drive tube (4) with tube bead a engaged in recess b; slide until lock screw (5) engages recess c; firmly tighten CLAMP screw (6). Lock screw 5 and clamp screw 6 are not interchangeable labels.
- For mowing-head mounting, section 4.2.1 says attach the KombiTool to the KombiEngine and gently lay the unit on its back with loop handle and shroud DOWN, shaft UP. This TI does not reproduce the complete powerhead/tool coupling or isolation procedure.
- Historical English-USA 2007 source, not present-day stock or approval for unlisted variants. No numeric serial cutoff is supplied. No physical interchange test was performed.
Source: TI 52/2007, p. 2 · TI 52/2007, p. 3 — FSB-KM: line-limiting blade and keyed deflector assembly.
No additional parts-table entry added.
Service note · FSB-KM
FSB-KM: AutoCut 11-2 assembly without a thrust plate
The cap turns clockwise; the PolyCut thrust plate must be removed.
- Figure 002TI039: install spring (1) in head (2); thread nylon-line ends (3) through eyelets (4), then insert spool (5). Ensure the line disengages from notches (6) during insertion and pull the ends to remove slack.
- Figure 002TI040: REMOVE the thrust plate from shaft (2), if fitted. Engage the head’s internal hexagon (3) with the shaft’s external hexagon (4). The thrust plate described for PolyCut is NOT used for this AutoCut installation.
- Figure 002TI041: put cap (5) on head (1), turn CLOCKWISE until fully threaded onto the shaft and firmly tighten. No numerical tightening torque is specified; the PolyCut stop-pin steps are not silently transferred to AutoCut.
- Historical English-USA 2007 source, not present-day stock or approval for unlisted variants. No numeric serial cutoff is supplied. No physical interchange test was performed.
Source: TI 52/2007, p. 3 · TI 52/2007, p. 4 — FSB-KM: AutoCut 11-2 assembly without a thrust plate.
Part numbers (1)
- 4004 710 2192 — AutoCut 11-2No thrust plate; clockwise cap · FSB-KM; source restrictions apply
Service note · FSB-KM
FSB-KM: PolyCut 5-3 thrust plate, stop pin and mounting
Use the supplied thrust plate and remove the stop pin after tightening.
- The thrust plate is supplied with PolyCut 5-3 and is required ONLY with that head in these instructions. Figure 002TI042 engages the plate’s internal hexagon (3) with shaft external hexagon (4).
- To block the shaft for installation AND removal, insert stop pin (5) through the deflector and a hole (6) in the thrust plate, rotating the plate back and forth if needed to align a hole. The drawing shows alternative plate-hole positions, not a drilling instruction.
- Figure 002TI044: install nut (7) in head (8); thread the head CLOCKWISE onto shaft (2); block the shaft; firmly tighten the head; REMOVE STOP PIN. The TI supplies no numerical torque or replacement-nut specification.
- Historical English-USA 2007 source, not present-day stock or approval for unlisted variants. No numeric serial cutoff is supplied. No physical interchange test was performed.
Source: TI 52/2007, p. 4 · TI 52/2007, p. 5 — FSB-KM: PolyCut 5-3 thrust plate, stop pin and mounting.
Part numbers (3)
- 4004 710 2180 — PolyCut 5-3Requires thrust plate · FSB-KM; source restrictions apply
- 4130 713 1501 — Thrust platePolyCut 5-3 · FSB-KM; source restrictions apply
- 4130 893 7800 — Stop pinRemove after tightening · FSB-KM; source restrictions apply
Service note · FSB-KM
FSB-KM: line sizes, PolyCut spares and shaft lubricant
The listed hedge-trimmer gear lubricant is applied to the drive-tube shaft.
- Section 5.1 weight is 1.54 lb (0.7 kg) WITHOUT cutting tool and deflector, not assembled operating weight.
- AutoCut 11-2 accessories: .080 inch diameter GREEN line, .095 inch diameter ORANGE line (both in different lengths), and prewound spool. Their order numbers are REFERRED to the Cutting Tools & Accessories for Brushcutters and Trimmers catalog, not printed here.
- PolyCut 5-3: plastic blades, pack of 12 = 4111 007 1001; thrust plate = 4130 713 1501; stop pin = 4130 893 7800. Plastic blades do not contradict the metal-cutting-tool exclusion.
- STIHL gear lubricant FOR HEDGE TRIMMERS is expressly listed for the SHAFT IN THE DRIVE TUBE: 3 oz / 80 g tube 0781 120 1109, or 8 oz / 225 g tube 0781 120 1110. These are package sizes, NOT doses to inject into the shaft; no lubrication interval or quantity per service is supplied.
- Historical English-USA 2007 source, not present-day stock or approval for unlisted variants. No numeric serial cutoff is supplied. No physical interchange test was performed.
Source: TI 52/2007, p. 5 — FSB-KM: line sizes, PolyCut spares and shaft lubricant.
Part numbers (5)
- 4111 007 1001 — Plastic blades, pack of 12PolyCut 5-3 · FSB-KM; source restrictions apply
- 4130 713 1501 — Thrust platePolyCut 5-3 · FSB-KM; source restrictions apply
- 4130 893 7800 — Stop pinPolyCut 5-3 · FSB-KM; source restrictions apply
- 0781 120 1109 — Gear lubricant, 3 oz / 80 g tubeDrive-tube shaft · FSB-KM; source restrictions apply
- 0781 120 1110 — Gear lubricant, 8 oz / 225 g tubeDrive-tube shaft · FSB-KM; source restrictions apply
Service note · FSB-KM
FSB-KM: catalog edition and FS 75 drive-tube repair allowances
References to manuals and labor times are not imported procedures or numeric times.
- Printed/electronic FSB-KM parts lists are reported available. The ORIGINAL page 5 scan names STIHL service catalogue (DVD-ROM issue 01/2008), from issue 01/2008; the catalogue name is lost in the body extraction. This is a historical inclusion claim, not verification of a particular installation.
- If the complete machine is started during repairs, section 8 requires ALL safety regulations and precautions in BOTH the FSB-KM and fitted KombiEngine instruction manuals. The KombiTools service manual is referenced for servicing and repair procedures.
- FS 75 DRIVE-TUBE repair times may be used for FSB-KM, assuming TRAINED personnel in a PROPERLY EQUIPPED workshop. No numerical time is printed, and this does not transfer all FS 75 engine repair allowances or prove physical parts interchange.
- The catalog/manual references are reviewed as reference statements only. Their complete procedures, accessory selection and numerical labor tables are not claimed recovered or whole-manual accepted by this TI review.
- Historical English-USA 2007 source, not present-day stock or approval for unlisted variants. No numeric serial cutoff is supplied. No physical interchange test was performed.
Source: TI 52/2007, p. 5 · TI 52/2007, p. 6 — FSB-KM: catalog edition and FS 75 drive-tube repair allowances.
No additional parts-table entry added.
Wrong number or missing part for the FSB-KM? Report a correction →