Stihl 4133 · Section D · 4 of 9 · 30 parts
Air filter, Fuel tank
Fits FC 72.
Historical fitment & changes (6) — includes parts and conditions not shown on this drawing.
Parts (30)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4133 129 0902 | Gasket Fitment / change note → | 1 |
| 2 | 9007 319 1121 | Hexagon head screw M5x56 Fitment / change note → | 2 |
| 3 | 4133 121 1602 | Spacer flange Fitment / change note → | 1 |
| 4 | 9022 341 1050 | Spline screw IS-M5x25 | 2 |
| 5 | 4133 182 7600 | Tensioner | 1 |
| 6 | 9022 341 0980 | Spline screw IS-M5x16 | 3 |
| 7 | 9214 320 0700 | Lock nut M5 | 1 |
| 8 | 9022 313 0680 | Spline screw IS-M4x16 | 1 |
| 9 | 4114 129 0501 | Gasket | 1 |
| 10 | 4133 120 0600 | Carburetor WT-227F | 1 |
| 10 | 4226 120 0601 | Carburetor WT-329 | 1 |
| 11 | 4114 149 1205 | Gasket | 1 |
| 12 | 4133 140 2800 | Filter housing | 1 |
| 13 | 9210 261 0700 | Hexagon nut M5 Fitment / change note → | 2 |
| 14 | 4133 124 2800 | Filter | 1 |
| 15 | 4133 124 1500 | Prefilter | 1 |
| 16 | 4133 141 0500 | Filter cover | 1 |
| 17 | 4133 350 0400 | Fuel tank | 1 |
| 18 | 4133 352 8100 | Insert | 1 |
| 19 | 0000 350 3502 | Pickup body Fitment / change note → | 1 |
| 20 | 4126 358 7700 | Hose with grommet | 1 |
| 21 | 4126 358 7762 | Hose | 1 |
| 22 | 4128 350 0505 | Filler cap | 1 |
| 23 | 0000 350 0900 | Rope | 1 |
| 24 | 0000 353 0800 | Filler cap retainer | 1 |
| 25 | 4133 084 0901 | Shroud | 1 |
| 26 | 4133 967 1502 | Model plate FC 72 | 1 |
| 27 | 4133 122 6900 | Plug Fitment / change note → | 2 |
| 28 | 9291 021 0120 | Washer 5.3 | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 4133 007 1051 | Set of gaskets | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Historical fitment · FC 72
FC 72: vented MIX cap must be exchanged as an assembly
4133 350 0501 replaces 4126 350 0502; old/new caps and vents are not individual mix-and-match parts.
X 26 535 367 — FC 72 vented cap assembly introduction only.
- From X 26 535 367, the new cap has a dedicated vent hole and molded MIX symbol; HDPE identifies plastic for recycling, not a separate part version. The old design vents through thread clearance. The vent hole must remain clear to keep tank and atmospheric pressure equal for correct carburetor operation; TI2.90 is a reference, not reviewed by proxy.
- Original/new cap and vent insert may only be exchanged AS ASSEMBLIES. Retainer 4116 350 0900 can be used with either cap. Old filler cap 4126 350 0502 is unavailable; new complete cap is 4133 350 0501.
- Tank vent 4126 350 5801 → 4133 350 5800; old vent while-stocks-last, then use new complete cap 4133 350 0501. New valve is 4114 353 1600; old valve has no separate spare number. New sealing ring is 4114 359 1200, not an assumed direct replacement for the original gasket. Cap includes keys 2–4; vent includes valve key 3.
- Historical English TI05/1994, series 4133 FC 72 only. Shared-series catalog grouping and references to standardization do not extend these cutoffs or restrictions to other models. Historical availability is not current stock. MOQ columns are commercial order quantities, not installation counts. No physical interchange test was performed.
Source: TI 5/1994, p. 8 · TI 5/1994, p. 9 — vented MIX cap must be exchanged as an assembly.
Part numbers (7)
- 4126 350 0502 — Original complete caporiginal · FC 72 — vented MIX cap must be exchanged as an assembly
- 4133 350 0501 — New complete vented capreplacement assembly · FC 72 — vented MIX cap must be exchanged as an assembly
- 4126 350 5801 — Original tank ventoriginal · FC 72 — vented MIX cap must be exchanged as an assembly
- 4133 350 5800 — New tank ventnew assembly component · FC 72 — vented MIX cap must be exchanged as an assembly
- 4114 353 1600 — New valvenew assembly component · FC 72 — vented MIX cap must be exchanged as an assembly
- 4114 359 1200 — New sealing ringnew assembly component · FC 72 — vented MIX cap must be exchanged as an assembly
- 4116 350 0900 — Retainer usable with either capretained · FC 72 — vented MIX cap must be exchanged as an assembly
IPL correction · FC 72
FC 72: original cap gasket belongs BELOW the tank vent
Incorrect assembly can leak fuel when the edger is on its side.
- Page 9 service note requires gasket 4126 359 0700 (key 4) BELOW tank vent (key 2), as illustrated. Incorrect assembly may cause fuel leakage when the unit is turned on its side. This is the ORIGINAL cap gasket: the table lists a separate new sealing ring 4114 359 1200. Do not add the original gasket to the new cap or defeat the cap/vent assembly-only rule.
- The bulletin corrects printed parts list 1992-10 and microfiche printed as “1193-02”; the original scan confirms that unusual year. Preserve the printed reference, not a silently repaired 1993 date. Original gasket remains available as a spare. No torque or tank-pressure test is supplied.
- Historical English TI05/1994, series 4133 FC 72 only. Shared-series catalog grouping and references to standardization do not extend these cutoffs or restrictions to other models. Historical availability is not current stock. MOQ columns are commercial order quantities, not installation counts. No physical interchange test was performed.
Source: TI 5/1994, p. 8 · TI 5/1994, p. 9 — original cap gasket belongs BELOW the tank vent.
Part numbers (2)
- 4126 359 0700 — Original cap gasket below tank ventcorrected placement · FC 72 — original cap gasket belongs BELOW the tank vent
- 4114 359 1200 — New cap sealing ring, not the old gasketdistinction only · FC 72 — original cap gasket belongs BELOW the tank vent
Historical fitment · FC 72
FC 72: universal pickup replaces old body and clip
0000 350 3502 replaces 4117 350 3505 and deletes clip 4126 358 8900 in the new arrangement.
- Introduction is “in progress”, with no machine cutoff. Universal pickup 0000 350 3502 has a larger-area strainer; longer life and improved dirt retention are source claims, not measured performance. Original body 4117 350 3505 (keys 2–5) and clip 4126 358 8900 (key 6) are replaced by the new assembly (key 1, includes filter key 5).
- Old pickup body is while-stocks-last. Strainer 4117 358 9300, ring 4117 358 8001 and clip 4126 358 8900 remain spares for older machines; that does not make the old clip necessary on the new assembly.
- Original filter 4117 358 1800 is supplied only up to ABOUT end of 1998, then use complete pickup 0000 350 3502. New filter is not separately available. Do not turn the historical approximate supply deadline into a production date or invent a standalone new filter number.
- Historical English TI05/1994, series 4133 FC 72 only. Shared-series catalog grouping and references to standardization do not extend these cutoffs or restrictions to other models. Historical availability is not current stock. MOQ columns are commercial order quantities, not installation counts. No physical interchange test was performed.
Source: TI 5/1994, p. 10 — universal pickup replaces old body and clip.
Part numbers (6)
- 0000 350 3502 — Universal pickup body assemblyreplacement · FC 72 — universal pickup replaces old body and clip
- 4117 350 3505 — Original pickup body assemblyoriginal · FC 72 — universal pickup replaces old body and clip
- 4117 358 9300 — Original strainerlegacy spare · FC 72 — universal pickup replaces old body and clip
- 4117 358 8001 — Original ringlegacy spare · FC 72 — universal pickup replaces old body and clip
- 4117 358 1800 — Original filter, historical supply deadlinelegacy spare · FC 72 — universal pickup replaces old body and clip
- 4126 358 8900 — Clip deleted from new arrangementlegacy spare · FC 72 — universal pickup replaces old body and clip
Service note · FC 72
FC 72: coupled engine power increase and repair restrictions
About 15% more power to 0.8 kW (1.1 bhp) requires all new parts when upgrading the original version.
X 31 578 923 — FC 72 engine power-increase introduction only; not FS 74/FS 76 cutoffs.
- From X 31 578 923, FC 72 power increases by approximately 15% to 0.8 kW (1.1 bhp). Changes are port timing, compression, intake cross-section, transfer-port shape, gasket and spacer-flange shape. No new displacement or universal output guarantee is given.
- New cylinder, gasket and spacer versions are generally used as replacement parts. Repairs to NEW-VERSION machines require ONLY NEW-TYPE parts; otherwise reduced power and malfunctions are expected. Original machines reach the claimed higher power only if ALL NEW PARTS are installed. A new gasket alone is not the complete power upgrade.
- Exact scope is FC 72, not FS 72 or every 4133 machine. Shared numbers and similar FS 74/FS 76 instructions do not transfer their changeovers or unprinted installation details to this edger.
- Historical TI 46/1994 guidance, not current stock, universal compatibility or physical verification. No hardware operation was performed.
Source: TI 46/1994, p. 1 · TI 46/1994, p. 2 · TI 46/1994, p. 3 — coupled engine power increase and repair restrictions.
No additional parts-table entry added.
Service note · FC 72
FC 72: wider intake gasket and directional compatibility
New 19 mm gasket window replaces 16 mm; the new gasket may be installed on old machines.
X 31 578 923 — FC 72 engine power-increase introduction only; not FS 74/FS 76 cutoffs.
- Gasket 4133 129 0900 becomes 4133 129 0902, MOQ 1. Its gas-mixture window grows from 16 to 19 mm. Figure 356TI002 distinguishes the old/new outlines; cylinder drawing 15/19 mm is a separate comparison, not a transcription correction to the gasket.
- The NEW gasket CAN be installed in OLD-VERSION machines. This does NOT imply reverse interchangeability: new-version repairs require new-type parts. Original gasket supplied only while existing factory stocks last (remark 3). The full power increase still requires all new parts.
- Historical TI 46/1994 guidance, not current stock, universal compatibility or physical verification. No hardware operation was performed.
Source: TI 46/1994, p. 2 · TI 46/1994, p. 3 — wider intake gasket and directional compatibility.
Part numbers (2)
- 4133 129 0900 — Original 16 mm-window gasketwhile stocks last · FC 72 only in the version/configuration described here
- 4133 129 0902 — New 19 mm-window gasketMOQ 1; may fit old version · FC 72 only in the version/configuration described here
Service note · FC 72
FC 72: new spacer flange, retained fasteners and supply limits
New bare flange is distinct from the old complete assembly; screw description conflicts with the later IPL.
X 31 578 923 — FC 72 engine power-increase introduction only; not FS 74/FS 76 cutoffs.
- New spacer opening is 19 mm on the cylinder-facing side. Installing it on old machines is subject to the service notes: all new parts for the stated power upgrade; only new-type parts for new-version repairs. TI 46 does not print the extra spacer attachment drawing found in other TIs; do not borrow its screw numbers or procedures.
- Old complete spacer assembly 4133 120 2202 includes table 3–6, has no new complete-assembly number and lasts only while factory stocks remain (remark 3). New bare spacer 4133 121 1602 is key 3, MOQ 1. Remark 4 says the OLD bare spacer was NOT AVAILABLE SEPARATELY. The old assembly inclusion range is not a promise that the new bare flange includes all fasteners.
- Unchanged in both columns:9007 319 1121 IS-M5x56 screws (key 4, 2x), 9210 261 0700 M5 hexagon nuts (key 5, 2x), 4133 122 6900 plugs (key 6, 2x). MOQ cells are blank. Two of each is an installed quantity. New cylinder 10 Nm is NOT a stated torque for this joint.
- SOURCE DESCRIPTION CONFLICT: TI 46 calls 9007 319 1121 a SPLINE screw; the linked 2012 FC 72 air-filter/fuel-tank IPL calls it a HEXAGON-HEAD screw M5x56. Preserve both; do not silently rewrite either source or infer a verified drive style from the shared number.
- Footer date 25 November1994, D1/MTK-na; prior TI 05/1994 is a provenance reference, not extra scope or a missing installation dependency.
- Historical TI 46/1994 guidance, not current stock, universal compatibility or physical verification. No hardware operation was performed.
Source: TI 46/1994, p. 2 · TI 46/1994, p. 3 — new spacer flange, retained fasteners and supply limits.
Part numbers (5)
- 4133 120 2202 — Original spacer-flange assembly; includes 3–6while stocks last · FC 72 only in the version/configuration described here
- 4133 121 1602 — New bare spacer flange; key 3MOQ 1; old bare part not separate · FC 72 only in the version/configuration described here
- 9007 319 1121 — IS-M5x56 screw; key 4, 2xunchanged; TI/IPL description conflict · FC 72 only in the version/configuration described here
- 9210 261 0700 — M5 hexagon nut; key 5, 2xunchanged; MOQ blank · FC 72 only in the version/configuration described here
- 4133 122 6900 — Plug; key 6, 2xunchanged; MOQ blank · FC 72 only in the version/configuration described here
Wrong number or missing part for the FC 72? Report a correction →