Stihl 4133 · Section C · 3 of 9 · 23 parts
Ignition system, Clutch
Fits FC 72.
Historical fitment & changes (4) — includes parts and conditions not shown on this drawing.
Parts (23)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4112 036 8600 | Woodruff key | 1 |
| 2 | 4133 400 1200 | Flywheel | 1 |
| 3 | 4133 400 1301 | Ignition module | 1 |
| 4 | not sold separately | Ignition lead 175 mm not available as a separate item | 1 |
| 5 | 0000 989 1012 | Grommet | 1 |
| 6 | 4133 405 8001 | Insulator | 1 |
| 7 | 4133 442 0400 | Insulating hose | 1 |
| 8 | 9022 371 0710 | Spline screw IS-M4x20 | 2 |
| 9 | 4133 160 2020 | Clutch Fitment / change note → | 1 |
| 10 | 4133 162 7900 | Tension spring Fitment / change note → | 2 |
| 11 | 4133 080 1800 | Fan housing | 1 |
| 12 | 4133 352 8105 | Insert | 2 |
| 13 | 4133 160 2900 | Clutch drum | 1 |
| 14 | 9455 621 1130 | Circlip 12x1 | 1 |
| 15 | 4123 791 9300 | Rubber insert | 1 |
| 16 | 9457 621 4481 | Circlip | 1 |
| 17 | 4133 790 7200 | Sleeve | 1 |
| 18 | 9074 478 4125 | Pan head self-tapping screw IS-5x14 | 1 |
| 19 | 9022 371 1020 | Spline screw IS-M5x20 → replaced by 9022 371 1050 TI 30/2004 | 1 |
| 20 | 9022 341 0980 | Spline screw IS-M5x16 | 3 |
| 21 | 4114 432 9201 | Grommet | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 0000 405 0600 NLA | Ignition lead 1 m not illustratedoption | 1 |
| — | 0000 930 2251 | Ignition lead 10 m not illustratedoption | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Historical fitment · FC 72
FC 72: complete clutch exchange; do not mix carriers and shoes
Modified carrier and shoes keep clutch number 4133 160 2000; individual old/new parts are not interchangeable.
X 24 849 657 — Carrier/shoe design introduction; not a dated cutoff for the later lined replacement clutch.
- From X 24 849 657, the modified carrier and shoes are NOT interchangeable with original individual parts. Replacement is a complete clutch assembly. The summary retains 4133 160 2000 for both versions, so that number alone cannot identify the design.
- Page 2 describes one dot on original shoes versus two dots on each modified shoe. Page 3 identification table allows original marking “--, 1” versus modified “2”; preserve the no-dot/one-dot table detail. Installed modified clutch has a narrower square head A. The modified clutch requires wrench 4133 893 1301. Unmodified clutch versions are while-stocks-last.
- Historical English TI05/1994, series 4133 FC 72 only. Shared-series catalog grouping and references to standardization do not extend these cutoffs or restrictions to other models. Historical availability is not current stock. MOQ columns are commercial order quantities, not installation counts. No physical interchange test was performed.
Source: TI 5/1994, p. 2 · TI 5/1994, p. 3 · TI 5/1994, p. 4 — complete clutch exchange; do not mix carriers and shoes.
Part numbers (2)
- 4133 160 2000 — Clutch, same number for changed carrier/shoessame-number revision · FC 72 — complete clutch exchange; do not mix carriers and shoes
- 4133 893 1301 — Wrench required for modified clutchrequired tool · FC 72 — complete clutch exchange; do not mix carriers and shoes
Historical fitment · FC 72
FC 72: new clutch wrench works with both clutch versions
4133 893 1301 replaces 4133 893 1300; old wrench is for the original clutch only.
- New wrench 4133 893 1301 can be used for all clutch versions covered here; old wrench 4133 893 1300 only for the original clutch. Tool replacement is “in progress”, not assigned the carrier production cutoff.
- The original scan separately labels opening SW and clutch head A: old wrench opening 13 mm (33/64 in), original clutch head 14 mm (9/16 in), marking -- or 1; new wrench opening 17 mm (43/64 in), modified clutch head 10 mm (13/32 in), marking 2. These apparently different dimensions describe distinct labeled features; do not normalize the table into a guessed matching socket size or fabricate a tool drawing. Old tool remains while stocks last.
- Historical English TI05/1994, series 4133 FC 72 only. Shared-series catalog grouping and references to standardization do not extend these cutoffs or restrictions to other models. Historical availability is not current stock. MOQ columns are commercial order quantities, not installation counts. No physical interchange test was performed.
Source: TI 5/1994, p. 2 · TI 5/1994, p. 3 · TI 5/1994, p. 4 — new clutch wrench works with both clutch versions.
Part numbers (2)
- 4133 893 1300 — Original clutch wrench, 13 mm SWoriginal tool · FC 72 — new clutch wrench works with both clutch versions
- 4133 893 1301 — New clutch wrench, 17 mm SWnew tool · FC 72 — new clutch wrench works with both clutch versions
Historical fitment · FC 72
FC 72: lined replacement clutch differs from production fit
4133 160 2020 is the supplied service clutch; FC 72 production continues with unlined shoes.
- To standardize with FS/HS 72/74/76, the FS 76 standard clutch 4133 160 2020 is supplied as an FC 72 spare in place of 4133 160 2000. The replacement uses lined shoes; FC 72 production still uses shoes WITHOUT linings. Do not infer that a serviced FC 72 with linings has a new production serial range.
- Complete replacement clutch includes two shoes (key 5) and two springs (key 6). Shoes are not separate spare items. The replacement is “in progress”; old complete clutch is while-stocks-last. This service assembly change does not override the prohibition on mixing old/new carrier and shoes in section 2.1.
- Historical English TI05/1994, series 4133 FC 72 only. Shared-series catalog grouping and references to standardization do not extend these cutoffs or restrictions to other models. Historical availability is not current stock. MOQ columns are commercial order quantities, not installation counts. No physical interchange test was performed.
Source: TI 5/1994, p. 3 · TI 5/1994, p. 4 — lined replacement clutch differs from production fit.
Part numbers (2)
- 4133 160 2000 — Original service clutchoriginal · FC 72 — lined replacement clutch differs from production fit
- 4133 160 2020 — Lined complete service clutch with two shoes and springsreplacement · FC 72 — lined replacement clutch differs from production fit
Historical fitment · FC 72
FC 72: modified spring hooks serve both shoe versions
4133 162 7900 keeps its number despite changed hook shape.
- A modified clutch spring has already been fitted as standard for some time; its hooks permit use with both original and new shoe versions. The summary prints 4133 162 7900 on both sides and two springs per clutch. Unmodified springs are while-stocks-last.
- No exact introduction serial is provided for this spring. Spring compatibility does not make the carriers and shoes individually interchangeable; section 2.1 still requires complete-clutch replacement.
- Historical English TI05/1994, series 4133 FC 72 only. Shared-series catalog grouping and references to standardization do not extend these cutoffs or restrictions to other models. Historical availability is not current stock. MOQ columns are commercial order quantities, not installation counts. No physical interchange test was performed.
Source: TI 5/1994, p. 3 · TI 5/1994, p. 4 — modified spring hooks serve both shoe versions.
Part numbers (1)
- 4133 162 7900 — Clutch spring, modified hooks, two per clutchsame-number revision · FC 72 — modified spring hooks serve both shoe versions
Wrong number or missing part for the FC 72? Report a correction →