Stihl 4133 · Section K · 9 of 9 · 24 parts
Deflector, Tools, Extras
Fits FC 72.
Historical fitment & changes (5) — includes parts and conditions not shown on this drawing.
Parts (24)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4133 713 4506 | Deflector Fitment / change note → | 1 |
| 2 | 4133 716 6505 | Clamp | 1 |
| 3 | 9214 320 0900 | Lock nut M6 | 2 |
| 4 | 9022 341 1350 | Spline screw IS-M6x25 | 1 |
| 5 | 9291 021 0140 | Washer 6.4 | 1 |
| 6 | 4133 710 9500 | Adjusting screw | 1 |
| 7 | 4133 716 6600 | Clamp | 1 |
| 8 | 9075 478 4095 | Pan head self-tapping screw IS-D5x12 | 3 |
| 9 | 4133 712 1000 | Wheel | 1 |
| 10 | 4133 712 1001 | Wheel option | 1 |
| 11 | 4133 713 6501 | Collar screw | 1 |
| 12 | 9291 021 0220 | Washer 13 Fitment / change note → | 1 |
| 13 | 9291 021 0200 | Washer 10.5 Fitment / change note → | 1 |
| 14 | 4133 716 3200 | Skirt | 1 |
| 15 | 0000 958 0512 | Washer | 1 |
| 16 | 4133 713 4101 | Blade Ø 200x2.4 mm / 7 7/8'' x 1/10'' | 1 |
| 17 | 0000 967 3730 | Warning pictogram | 1 |
| 18 | 1129 890 3401 | Combination wrench option | 1 |
| 19 | 4130 893 7800 | Locking pin option | 1 |
| 20 | 0000 890 2300 NLA | Screwdriver option | 1 |
| 21 | 0812 370 1000 | Screwdriver T27x120x70 | 1 |
| 22 | 0000 884 0307 | Safety glasses | 1 |
| 23 | 0000 891 0801 NLA | Tool roll option | 1 |
| 30 | 1114 890 3401 | Combination wrench Fitment / change note → | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Historical fitment · FC 72
FC 72: new clutch wrench works with both clutch versions
4133 893 1301 replaces 4133 893 1300; old wrench is for the original clutch only.
- New wrench 4133 893 1301 can be used for all clutch versions covered here; old wrench 4133 893 1300 only for the original clutch. Tool replacement is “in progress”, not assigned the carrier production cutoff.
- The original scan separately labels opening SW and clutch head A: old wrench opening 13 mm (33/64 in), original clutch head 14 mm (9/16 in), marking -- or 1; new wrench opening 17 mm (43/64 in), modified clutch head 10 mm (13/32 in), marking 2. These apparently different dimensions describe distinct labeled features; do not normalize the table into a guessed matching socket size or fabricate a tool drawing. Old tool remains while stocks last.
- Historical English TI05/1994, series 4133 FC 72 only. Shared-series catalog grouping and references to standardization do not extend these cutoffs or restrictions to other models. Historical availability is not current stock. MOQ columns are commercial order quantities, not installation counts. No physical interchange test was performed.
Source: TI 5/1994, p. 2 · TI 5/1994, p. 3 · TI 5/1994, p. 4 — new clutch wrench works with both clutch versions.
Part numbers (2)
- 4133 893 1300 — Original clutch wrench, 13 mm SWoriginal tool · FC 72 — new clutch wrench works with both clutch versions
- 4133 893 1301 — New clutch wrench, 17 mm SWnew tool · FC 72 — new clutch wrench works with both clutch versions
Historical fitment · FC 72
FC 72: 70° deflector stop and gearhead revision
New deflector and gearhead are fully interchangeable with original versions on FC 72.
X 26 392 834 — Gearhead/deflector stop introduction; also printed for wheel and blade revisions, not output bearing.
- From X 26 392 834, gearhead 4133 640 0105 → 4133 640 0106 and deflector 4133 713 4505 → 4133 713 4506 standardize with the EC 70 stop arrangement. Two deflector lugs D contact stop C on the gearhead. Rotational adjustment A is 70°; the bulletin states it does not restrict FC 72 depth-of-cut adjustment B.
- Original/new gearhead and deflector are fully interchangeable. After fitting the new versions, the dealer MUST inform the user that rotational movement is limited by stops. This does not remove the separate wheel and blade hardware pairing restrictions.
- The complete gearhead summary includes keys 2, 3, 7, 8, 10 and 11: housing, deflector, guard ring, locknut, service screw plug and output bearing. Gear housing changes 4133 641 0301 → 4133 641 0306; original housing is no longer available, while original complete gearhead and deflector are while-stocks-last. The bearing direction conflict is retained separately; the inclusion list does not resolve it.
- Historical English TI05/1994, series 4133 FC 72 only. Shared-series catalog grouping and references to standardization do not extend these cutoffs or restrictions to other models. Historical availability is not current stock. MOQ columns are commercial order quantities, not installation counts. No physical interchange test was performed.
Source: TI 5/1994, p. 4 · TI 5/1994, p. 6 · TI 5/1994, p. 7 — 70° deflector stop and gearhead revision.
Part numbers (6)
- 4133 640 0105 — Gearhead assemblyoriginal · FC 72 — 70° deflector stop and gearhead revision
- 4133 640 0106 — Gearhead assemblynew · FC 72 — 70° deflector stop and gearhead revision
- 4133 641 0301 — Gear housingoriginal · FC 72 — 70° deflector stop and gearhead revision
- 4133 641 0306 — Gear housingnew · FC 72 — 70° deflector stop and gearhead revision
- 4133 713 4505 — Deflectororiginal · FC 72 — 70° deflector stop and gearhead revision
- 4133 713 4506 — Deflectornew · FC 72 — 70° deflector stop and gearhead revision
Historical fitment · FC 72
FC 72: depth-wheel screw requires A 10.3 washer
The new shoulder screw must use A 10.3 at its threaded end; A 13 there prevents free wheel rotation.
X 26 392 834 — New depth-wheel screw/washer introduction only.
- From X 26 392 834, modified shoulder screw and washer are introduced. Old/new individual versions are NOT interchangeable. New A 10.3 washer 9291 021 0200 sits on the threaded end of the new screw, between deflector and wheel. Using original A 13 at that location prevents the wheel from rotating freely.
- Kit 4133 710 8750 includes new shoulder screw plus A 13 and A 10.3 washers (keys 4–6); available up to ABOUT the end of 1996, after which individual kit parts are to be used. The new shoulder-screw cell is printed -*- without an order number; no new screw number is invented. Original screw 4133 713 6500 is while-stocks-last.
- A 13 washer 9291 021 0220 remains, but its installation quantity is reduced from two to one by remark 3. A 10.3 is the additional location-specific washer. MOQ 10 for each washer is not ten washers per machine. The cross-section confirms wheel E, screw 4, washer 6 and deflector 3 placement.
- Historical English TI05/1994, series 4133 FC 72 only. Shared-series catalog grouping and references to standardization do not extend these cutoffs or restrictions to other models. Historical availability is not current stock. MOQ columns are commercial order quantities, not installation counts. No physical interchange test was performed.
Source: TI 5/1994, p. 5 · TI 5/1994, p. 6 · TI 5/1994, p. 7 — depth-wheel screw requires A 10.3 washer.
Part numbers (4)
- 4133 710 8750 — Shoulder screw kit, historical temporary supplykit · FC 72 — depth-wheel screw requires A 10.3 washer
- 4133 713 6500 — Original shoulder screworiginal · FC 72 — depth-wheel screw requires A 10.3 washer
- 9291 021 0220 — A 13 washer, quantity reduced to oneretained · FC 72 — depth-wheel screw requires A 10.3 washer
- 9291 021 0200 — A 10.3 washer at new screw threaded endrequired companion · FC 72 — depth-wheel screw requires A 10.3 washer
Historical fitment · FC 72
FC 72: 19 mm locknut requires the new guard ring
Old 13 mm locknut works with either ring; new 19 mm locknut only with the larger-recess ring.
X 26 392 834 — FC 72 blade mounting nut/ring introduction.
- From X 26 392 834, 13 mm a/f flange locknut 4133 642 7600 is replaced by 19 mm 4133 642 7601 and guard ring 4133 717 2700 changes to larger-recess 4133 717 2701. The new locknut wrench size matches the spark plug; no torque or thread dimension is specified.
- The 13 mm locknut can be used with original OR new ring. The 19 mm locknut can ONLY be used with the new ring. Since the old locknut is no longer supplied, service replacement requires BOTH new nut and new ring. Original guard ring is while-stocks-last. The changed supplied combination wrench is handled in section 9.
- Historical English TI05/1994, series 4133 FC 72 only. Shared-series catalog grouping and references to standardization do not extend these cutoffs or restrictions to other models. Historical availability is not current stock. MOQ columns are commercial order quantities, not installation counts. No physical interchange test was performed.
Source: TI 5/1994, p. 5 · TI 5/1994, p. 6 · TI 5/1994, p. 7 — 19 mm locknut requires the new guard ring.
Part numbers (4)
- 4133 717 2700 — Guard ringoriginal · FC 72 — 19 mm locknut requires the new guard ring
- 4133 717 2701 — Guard ringnew · FC 72 — 19 mm locknut requires the new guard ring
- 4133 642 7600 — Flange locknutoriginal · FC 72 — 19 mm locknut requires the new guard ring
- 4133 642 7601 — Flange locknutnew · FC 72 — 19 mm locknut requires the new guard ring
Historical fitment · FC 72
FC 72: supplied wrench changes with 19 mm blade nut
1119 890 3405 has one 19 mm socket; old 1114 890 3401 has 13 and 19 mm sockets.
X 26 392 834 — Supplied combination wrench change with blade-nut revision.
- From X 26 392 834, FC 72 is supplied with combination wrench 1119 890 3405 instead of 1114 890 3401 because of the new 19 mm blade locknut. Original wrench has 13 and 19 mm sockets; new wrench has only one 19 mm socket. The old wrench remains available as a spare.
- This supplied tool change does not prove which nut/guard combination is currently installed on a serviced machine. Section 3.3 pairing restrictions remain controlling. Footer TI50.92 is a prior-information pointer, not reviewed by proxy. Bulletin publication: Waiblingen, May 4, 1994.
- Historical English TI05/1994, series 4133 FC 72 only. Shared-series catalog grouping and references to standardization do not extend these cutoffs or restrictions to other models. Historical availability is not current stock. MOQ columns are commercial order quantities, not installation counts. No physical interchange test was performed.
Source: TI 5/1994, p. 12 — supplied wrench changes with 19 mm blade nut.
Part numbers (2)
- 1114 890 3401 — Original 13/19 mm combination wrenchoriginal tool · FC 72 — supplied wrench changes with 19 mm blade nut
- 1119 890 3405 — New single 19 mm socket combination wrenchnew tool · FC 72 — supplied wrench changes with 19 mm blade nut
Wrong number or missing part for the FC 72? Report a correction →