← Edgers & other equipment · series 4133

Stihl 4133 · Section J · 8 of 9 · 29 parts

Drive tube assembly, Loop handle, Gear head

Fits FC 72.

Parts diagrams →

Historical fitment & changes (5) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
110111213141516171819220212223242526344056789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (29)

PosPart numberDescriptionQty
1 4133 710 7101 Drive tube assembly Ø 25.4 mm / 1'' 1
2 4137 711 3202 Drive shaft 1
3 4133 717 2000 Cap 1
4 4133 641 0306 Gear housing Fitment / change note → 1
5 9503 003 9491 Grooved ball bearing 629-2Z 1
6 not sold separately Drive pinion not available as a separate item 1
7 not sold separately Spur bevel gear not available as a separate item 1
8 9503 003 9850 Grooved ball bearing 609 → replaced by 9503 003 9853 TI 46/2000 1
9 9503 003 9853 Grooved ball bearing 609-2Z 1
10 9455 621 0750 Circlip 9x1 1
11 9456 621 2660 Circlip 24x1.2 1
12 4133 642 0600 Drive shaft 1
13 9503 003 6440 Grooved ball bearing 6201-2RS Fitment / change note → → replaced by 9503 003 6420 TI 5/1994 1
14 9456 621 3600 Circlip 32x1.2 1
15 4119 713 6500 Screw plug Fitment / change note → 1
16 9022 341 1300 Spline screw IS-M6x20 1
17 4133 713 1501 Thrust plate 1
18 4133 717 2701 Guard ring Fitment / change note → 1
19 4133 642 7601 Collar nut Fitment / change note → 1
20 4130 790 1200 Loop handle 1
21 4130 791 2000 Handle hose 1
22 9075 478 4115 Pan head self-tapping screw IS-D5x16 1
23 4130 791 6805 Clamp 1
24 9022 341 1430 Spline screw IS-M6x50 1
25 9294 021 0140 Washer 6.4 1
26 9222 068 0900 Square nut M6 1
40 4133 642 7600 Collar nut Fitment / change note → 1
Not numbered on the diagram — assemblies, kits and options
— 4133 640 0106 Gearhead Fitment / change note → 1
— 4133 640 7300 Set of pinions 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Historical fitment · FC 72

FC 72: 70° deflector stop and gearhead revision

New deflector and gearhead are fully interchangeable with original versions on FC 72.

X 26 392 834 — Gearhead/deflector stop introduction; also printed for wheel and blade revisions, not output bearing.

  • From X 26 392 834, gearhead 4133 640 0105 → 4133 640 0106 and deflector 4133 713 4505 → 4133 713 4506 standardize with the EC 70 stop arrangement. Two deflector lugs D contact stop C on the gearhead. Rotational adjustment A is 70°; the bulletin states it does not restrict FC 72 depth-of-cut adjustment B.
  • Original/new gearhead and deflector are fully interchangeable. After fitting the new versions, the dealer MUST inform the user that rotational movement is limited by stops. This does not remove the separate wheel and blade hardware pairing restrictions.
  • The complete gearhead summary includes keys 2, 3, 7, 8, 10 and 11: housing, deflector, guard ring, locknut, service screw plug and output bearing. Gear housing changes 4133 641 0301 → 4133 641 0306; original housing is no longer available, while original complete gearhead and deflector are while-stocks-last. The bearing direction conflict is retained separately; the inclusion list does not resolve it.
  • Historical English TI05/1994, series 4133 FC 72 only. Shared-series catalog grouping and references to standardization do not extend these cutoffs or restrictions to other models. Historical availability is not current stock. MOQ columns are commercial order quantities, not installation counts. No physical interchange test was performed.

Source: TI 5/1994, p. 4 · TI 5/1994, p. 6 · TI 5/1994, p. 7 — 70° deflector stop and gearhead revision.

Part numbers (6)
  • 4133 640 0105 — Gearhead assemblyoriginal · FC 72 — 70° deflector stop and gearhead revision
  • 4133 640 0106 — Gearhead assemblynew · FC 72 — 70° deflector stop and gearhead revision
  • 4133 641 0301 — Gear housingoriginal · FC 72 — 70° deflector stop and gearhead revision
  • 4133 641 0306 — Gear housingnew · FC 72 — 70° deflector stop and gearhead revision
  • 4133 713 4505 — Deflectororiginal · FC 72 — 70° deflector stop and gearhead revision
  • 4133 713 4506 — Deflectornew · FC 72 — 70° deflector stop and gearhead revision

Historical fitment · FC 72

FC 72: depth-wheel screw requires A 10.3 washer

The new shoulder screw must use A 10.3 at its threaded end; A 13 there prevents free wheel rotation.

X 26 392 834 — New depth-wheel screw/washer introduction only.

  • From X 26 392 834, modified shoulder screw and washer are introduced. Old/new individual versions are NOT interchangeable. New A 10.3 washer 9291 021 0200 sits on the threaded end of the new screw, between deflector and wheel. Using original A 13 at that location prevents the wheel from rotating freely.
  • Kit 4133 710 8750 includes new shoulder screw plus A 13 and A 10.3 washers (keys 4–6); available up to ABOUT the end of 1996, after which individual kit parts are to be used. The new shoulder-screw cell is printed -*- without an order number; no new screw number is invented. Original screw 4133 713 6500 is while-stocks-last.
  • A 13 washer 9291 021 0220 remains, but its installation quantity is reduced from two to one by remark 3. A 10.3 is the additional location-specific washer. MOQ 10 for each washer is not ten washers per machine. The cross-section confirms wheel E, screw 4, washer 6 and deflector 3 placement.
  • Historical English TI05/1994, series 4133 FC 72 only. Shared-series catalog grouping and references to standardization do not extend these cutoffs or restrictions to other models. Historical availability is not current stock. MOQ columns are commercial order quantities, not installation counts. No physical interchange test was performed.

Source: TI 5/1994, p. 5 · TI 5/1994, p. 6 · TI 5/1994, p. 7 — depth-wheel screw requires A 10.3 washer.

Part numbers (4)
  • 4133 710 8750 — Shoulder screw kit, historical temporary supplykit · FC 72 — depth-wheel screw requires A 10.3 washer
  • 4133 713 6500 — Original shoulder screworiginal · FC 72 — depth-wheel screw requires A 10.3 washer
  • 9291 021 0220 — A 13 washer, quantity reduced to oneretained · FC 72 — depth-wheel screw requires A 10.3 washer
  • 9291 021 0200 — A 10.3 washer at new screw threaded endrequired companion · FC 72 — depth-wheel screw requires A 10.3 washer

Historical fitment · FC 72

FC 72: 19 mm locknut requires the new guard ring

Old 13 mm locknut works with either ring; new 19 mm locknut only with the larger-recess ring.

X 26 392 834 — FC 72 blade mounting nut/ring introduction.

  • From X 26 392 834, 13 mm a/f flange locknut 4133 642 7600 is replaced by 19 mm 4133 642 7601 and guard ring 4133 717 2700 changes to larger-recess 4133 717 2701. The new locknut wrench size matches the spark plug; no torque or thread dimension is specified.
  • The 13 mm locknut can be used with original OR new ring. The 19 mm locknut can ONLY be used with the new ring. Since the old locknut is no longer supplied, service replacement requires BOTH new nut and new ring. Original guard ring is while-stocks-last. The changed supplied combination wrench is handled in section 9.
  • Historical English TI05/1994, series 4133 FC 72 only. Shared-series catalog grouping and references to standardization do not extend these cutoffs or restrictions to other models. Historical availability is not current stock. MOQ columns are commercial order quantities, not installation counts. No physical interchange test was performed.

Source: TI 5/1994, p. 5 · TI 5/1994, p. 6 · TI 5/1994, p. 7 — 19 mm locknut requires the new guard ring.

Part numbers (4)
  • 4133 717 2700 — Guard ringoriginal · FC 72 — 19 mm locknut requires the new guard ring
  • 4133 717 2701 — Guard ringnew · FC 72 — 19 mm locknut requires the new guard ring
  • 4133 642 7600 — Flange locknutoriginal · FC 72 — 19 mm locknut requires the new guard ring
  • 4133 642 7601 — Flange locknutnew · FC 72 — 19 mm locknut requires the new guard ring

Historical fitment · FC 72

FC 72: hex-head gear plug is a service replacement

4119 713 6500 adds a 13 mm hexagon to the Torx socket; production keeps a plug without hexagon.

  • Service screw plug 4119 713 6500 replaces 4117 713 6501. It has both a Torx spline socket and 13 mm hexagon (approximately 1/2 in a/f) to aid releasing a tight plug. A plug WITHOUT hexagon continues on the production line.
  • Change is “in progress”, not the gearhead serial cutoff. Original 4117 713 6501 remains available for other models; no universal model list, tightening torque or thread-size interchange is supplied.
  • Historical English TI05/1994, series 4133 FC 72 only. Shared-series catalog grouping and references to standardization do not extend these cutoffs or restrictions to other models. Historical availability is not current stock. MOQ columns are commercial order quantities, not installation counts. No physical interchange test was performed.

Source: TI 5/1994, p. 6 · TI 5/1994, p. 7 — hex-head gear plug is a service replacement.

Part numbers (2)
  • 4117 713 6501 — Original non-hex plug, retained for other modelsoriginal · FC 72 — hex-head gear plug is a service replacement
  • 4119 713 6500 — Hex-head plus Torx service plugservice replacement · FC 72 — hex-head gear plug is a service replacement

IPL correction · FC 72

FC 72: output-bearing replacement direction is unresolved

Narrative says 6440 → 6420; table says 6420 → 6440. Neither direction is verified.

  • Section 3.5 narrative states output-shaft bearing 9503 003 6440 will be replaced by 9503 003 6420. The original page 6 summary instead lists ORIGINAL 9503 003 6420 and NEW 9503 003 6440. Both readings are confirmed in the scan; this is an unresolved source contradiction, not an OCR correction.
  • Page 7 says section 3.5 applies “since start of production”, while the narrative uses future replacement wording; the table marks the original bearing unavailable. Retain these statements without selecting a supersession direction or assigning X 26 392 834. No bearing dimensions or independent interchange evidence are provided.
  • Historical English TI05/1994, series 4133 FC 72 only. Shared-series catalog grouping and references to standardization do not extend these cutoffs or restrictions to other models. Historical availability is not current stock. MOQ columns are commercial order quantities, not installation counts. No physical interchange test was performed.

Source: TI 5/1994, p. 6 · TI 5/1994, p. 7 — output-bearing replacement direction is unresolved.

Part numbers (2)
  • 9503 003 6440 — Original in prose, new in tableconflicting source roles · FC 72 — output-bearing replacement direction is unresolved
  • 9503 003 6420 — New in prose, original in tableconflicting source roles · FC 72 — output-bearing replacement direction is unresolved

Wrong number or missing part for the FC 72? Report a correction →