← Edgers & other equipment · series 4133

Stihl 4133 · Section H · 7 of 16 · 23 parts

Drive tube assembly FS 72, Loop handle

Fits FS 72.

Parts diagrams →

Historical fitment & changes (1) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
110111213141516171819220212223345677899
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (23)

PosPart numberDescriptionQty
1 4133 710 7100 Drive tube assembly Ø 25.4 mm / 1'' Fitment / change note → 1
2 4130 711 3200 Drive shaft Fitment / change note → 1
3 4133 717 2000 Cap 1
4 9455 621 1130 Circlip 12x1 1
5 9099 021 2360 Self-tapping screw 3.5x9.5 1
6 4130 640 1405 Bearing housing 1
7 9513 003 3210 Needle cage 12x16x10 2
8 4130 640 2205 Drive shaft 1
9 0000 958 1233 Washer 2
10 4130 713 1501 Thrust plate 1
11 4130 710 6701 Hose clamp 1
12 9022 341 1010 Spline screw IS-M5x18 1
13 9210 260 0700 Hexagon nut M5 1
14 4130 713 4501 Deflector 1
15 4130 713 4100 Blade 1
16 9074 478 4405 Pan head self-tapping screw IS-P6x14 1
17 9771 021 2760 Hose clip Ø 1 7/8x1/2" 1
18 4130 790 1300 Loop handle 1
19 4130 791 2000 Handle hose 1
20 9075 478 4115 Pan head self-tapping screw IS-D5x16 1
21 4130 791 6805 Clamp 1
22 9041 116 1430 Pan head screw M6x50 1
23 9222 068 0900 Square nut M6 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · FS 72 / FS 75

FS 72 / short FS 75: shared replacement tube needs the correct fixing hole

4133 710 7100 is pre-drilled for FS72; short FS75 needs its separate 6 mm hole.

  • To standardize spares, FS72 tube4133 710 7100 is supplied also for SHORT-SHAFT FS75, replacing4137 710 7110 in that short configuration. FS72 keeps4133 710 7100. Both new supply rows carry remark2: WITH DRILLING TEMPLATE. Original FS75 tube stock exhaustion is remark1. The shared short shaft4130 711 3200 stays unchanged and available as a spare (remark4). This is not the longer7112/3210 assembly.
  • The source says the only tube difference between FS72 and FS75 in this SHORT-SHAFT replacement context is fixing-screw hole position. Replacement7100 is PRE-DRILLED FOR FS72. Drill the separate FS75 hole using template4; PEEL THE TEMPLATE OFF BEFORE fitting the shaft in the AV sleeve. Figure392TI012 KN shows the template aligned with the existing hole; its printed label is0000 967 3722 A SAL. The printed identifier is not evidence of separate factory supply.
  • Without a template, page2 drawing392TI013 KN locates hole centers from the SAME RIGHT-HAND TUBE END: FS75 at66.3 mm (printed66,3; 2 5/8 in.), FS72 at54 mm (2 1/8 in.). The FS75 hole diameter is6 mm (1/4 in.). These are center-to-end distances, not center spacing, tube length or drilling depth. The new FS75 center lies farther from the end than the existing FS72 center; do not reverse the labels. Printed metric and inch values are retained, not treated as exact mathematical conversions.
  • Flexible liner is unnumbered and not separately available. No cutting, bore depth, through-both-walls direction, alternative hole angle or screw torque is specified; no extra instruction invented. This source is sufficient for the recorded template/no-template distinction, not a complete machine disassembly manual. FS72 supply change is IN PROGRESS; X36 865 750 belongs to longer FS75 production, not a drilling cutoff.
  • Bind only exact FS72 and FS75 drive-tube sheets. Other FS74/76/80/85 shared-sheet models do not inherit this drilling permission. Footer references TI12.95 and TI36.96 are prior-model bibliography, not missing procedural dependencies. All page1 diagrams, page2 dimensions, six table rows and four supply remarks reviewed.
  • Historical source guidance and factory supply, not current availability or verified physical interchange. No hardware operation was performed.

Source: TI 35/1997, p. 1 · TI 35/1997, p. 2 — Page1 short-shaft replacement/template and removal; page2 dimensional drawing and full summary.

Part numbers (4)
  • 4137 710 7110 — Original short FS75 drive tubeFactory stock exhaustion · Only the exact model/configuration and restrictions of 1997-35
  • 4133 710 7100 — FS72 / short FS75 replacement tubeSupplied with drilling template · Only the exact model/configuration and restrictions of 1997-35
  • 4130 711 3200 — Shared short drive shaftUnchanged; remains spare · Only the exact model/configuration and restrictions of 1997-35
  • 0000 967 3722 — Drilling-template printed identifierFigure label; separate orderability not established · Only the exact model/configuration and restrictions of 1997-35

Wrong number or missing part for the FS 72? Report a correction →