Stihl 4134 · Section A · 1 of 12 · 30 parts
Crankcase, Cylinder
Fits BT 120 C.
Historical fitment & changes (4) — includes parts and conditions not shown on this drawing.
Parts (30)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4134 020 2600 | Crankcase | 1 |
| 2 | 0000 988 8600 | Sleeve | 4 |
| 3 | 9503 003 0242 | Grooved ball bearing 6201 | 2 |
| 4 | 4134 020 2900 | Crankcase | 1 |
| 5 | 9640 003 1195 | Oil seal 12x22x5 Fitment / change note → | 2 |
| 6 | 4134 030 0403 | Crankshaft | 1 |
| 7 | 4140 036 0300 | Washer | 2 |
| 8 | 9075 478 4159 | Pan head self-tapping screw IS-D5x24 | 7 |
| 9 | 4134 029 2300 | Cylinder gasket | 1 |
| 10 | 9512 003 2250 | Needle cage 10x13x12.5 | 1 |
| 11 | 4134 020 1213 | Cylinder with piston Ø 35 mm | 1 |
| 12 | 4134 030 2011 | Piston Ø 35 mm | 1 |
| 13 | 4119 034 3001 | Piston ring Ø 35x1.5 mm | 2 |
| 14 | 4119 034 1500 | Piston pin 10x6.5x28 | 1 |
| 15 | 9463 650 1000 | Snap ring 10 | 2 |
| 16 | 9075 478 4175 | Pan head self-tapping screw IS-D5x28 | 4 |
| 17 | 0000 400 7000 | Spark plug NGK BPMR7A | 1 |
| 17 | 1110 400 7005 | Spark plug Bosch WSR 6 F | 1 |
| 18 | 4134 149 0600 | Muffler gasket | 1 |
| 19 | 4134 140 0603 | Muffler | 1 |
| 20 | 4134 140 0607 NLA | Muffler | 1 |
| 21 | 4128 140 6900 NLA | Stub with screen | 1 |
| 22 | 4134 084 0912 | Shroud | 1 |
| 23 | 4134 080 1601 NLA | Shroud Fitment / change note → | 1 |
| 24 | 4134 967 1514 NLA | Model plate Fitment / change note → | 1 |
| 25 | 9022 341 1019 | Spline screw IS-M5x20 | 2 |
| 26 | 0000 951 1100 | Screw IS-D5x20 | 2 |
| 27 | 0783 830 2000 | Tube of sealant Dirko HT red option | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 4134 007 1050 | Set of gaskets | 1 |
| — | 4134 140 0653 NLA | Muffler Fitment / change note → | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Conditional replacement · BT 120 C / FS 120 / FS 200 / FS 250 / FS 350
TI09: narrower crankshaft oil seals retrofit older machines
The 12x22x5 seal replaces the 12x22x7 seal; no installation-depth value is invented.
- To facilitate installation, 7 mm wide oil seal 9640 003 1200 (DIN3760-BS12x22x7) is replaced by 5 mm wide seal 9640 003 1195 (DIN3760-BS12x22x5). The diameter pair remains 12 x 22 mm; the changed dimension is width.
- The new seals may also be used in older machines and are installed in the same way as before. The diagram shows their crankshaft locations but supplies no numerical seating depth or alternate installation method.
- Introduction is in progress; the previous seal is no longer available from the factory. No serial cutoff is stated here, and the preceding clutch USA serial must not be applied to these seals.
- Only the printed TI09/2003 models and described configurations are covered. Shared catalog sheets do not extend this assertion to FS 300, BT 121, SP 200, HT 250 or unlisted R variants. No physical interchange test was performed.
Source: TI 9/2003, p. 1 · TI 9/2003, p. 21 · TI 9/2003, p. 22 — 6 oil seals and summary.
Part numbers (2)
- 9640 003 1200 — Oil seal12x22x7Previous; discontinued factory supply · TI09/2003 section 6 oil seals and summary models/configurations only; preserve restrictions above
- 9640 003 1195 — Oil seal12x22x5New; older-machine use allowed · TI09/2003 section 6 oil seals and summary models/configurations only; preserve restrictions above
Conditional replacement · FS 120 / FS 200 / FS 350 / BT 120 C
TI22: shrouds, round model plates and replacement labels
The label sheet does not extend machine fitment to every model pictured on it.
- Round model plates move from shroud to the modified fan housing; company logo moves to the shroud. New shrouds lose the old plate seat and change contour for ignition-lead routing. FS 120/200/350 shroud 4134 084 0902 becomes 4134 080 1600; BT 120 C 4134 084 0907 becomes 4134 080 1601. Previous shrouds are no longer factory supplied.
- New replacement shrouds include model-label sheet 4134 967 1514. For an old machine, apply its appropriate label to shaded area 2 of illustration 250TI037. Labels pictured for FS 250, FS 300 and FR 350 do not prove all other update parts fit those models. Only the shroud with decompression-valve opening 3 (from FS 350) is supplied as replacement for the stated models; this does not add a decompression valve to a machine.
- Round plate pairs: FS 120 4134 967 1503 to 4134 967 1511; FS 200 4134 967 1502 to 4134 967 1510; FS 350 4134 967 1500 to 4134 967 1507; BT 120 C 4313 967 1500 to 4313 967 1501. Previous plates are supplied only while stocks last. Introduction follows section5.3 (in progress). Observe section8 muffler sets and sections7/9/10 ignition/cooling dependencies when replacing shrouds; labels alone are not a complete conversion.
- TI22 describes an interdependent update package. Its introduction says most new parts were fitted to FS 250 from production start, with unspecified exceptions; this is not blanket FS 250 fitment approval. Shared sheets do not extend the named model/configuration scope. Factory availability is historical, not current stock. No physical interchange test was performed.
Source: TI 22/2001, p. 5 · TI 22/2001, p. 7 · TI 22/2001, p. 8 — 6 all illustrations, service/replacement notes and split summary.
Part numbers (13)
- 4134 084 0902 — Previous shroudNo longer factory supplied · FS 120 / FS 200 / FS 350
- 4134 084 0907 — Previous shroudNo longer factory supplied · BT 120 C
- 4134 080 1600 — New shroudIncludes label sheet · FS 120 / FS 200 / FS 350
- 4134 080 1601 — New shroudIncludes label sheet · BT 120 C
- 4134 967 1514 — Sheet with adhesive model labelsChoose actual machine label · FS 120, FS 200, FS 350, BT 120 C; stated configuration only
- 4134 967 1503 — Previous model platePrevious; stocks only · FS 120
- 4134 967 1511 — Round model plateNew fan-housing plate · FS 120
- 4134 967 1502 — Previous model platePrevious; stocks only · FS 200
- 4134 967 1510 — Round model plateNew fan-housing plate · FS 200
- 4134 967 1500 — Previous model platePrevious; stocks only · FS 350
- 4134 967 1507 — Round model plateNew fan-housing plate · FS 350
- 4313 967 1500 — Previous model platePrevious; stocks only · BT 120 C
- 4313 967 1501 — Round model plateNew fan-housing plate · BT 120 C
Conditional replacement · BT 120 C
BT 120 C: updated muffler-with-shroud set
Set includes the revised shroud and model-label sheet; cooling and ignition dependencies still apply.
- Muffler-with-shroud set 4134 140 0651 becomes 4134 140 0653, including shroud 4134 080 1601 instead of 4134 084 0907. Shroud includes adhesive model-label sheet 4134 967 1514; choose the correct label for an old machine. Shroud revision accompanies changed ignition lead routing and model-plate position.
- Previous set and shroud are no longer factory supplied. Introduction follows section5.3, in progress for all named models. These are set order numbers, not evidence that every similarly numbered bare muffler is interchangeable.
- This is the separate BT 120 C set pair, not the FS set. The FS 120/200 index-C clutch shroud and FS 350 clutch-cover instructions are not extended to the auger.
- TI22 describes an interdependent update package. Its introduction says most new parts were fitted to FS 250 from production start, with unspecified exceptions; this is not blanket FS 250 fitment approval. Shared sheets do not extend the named model/configuration scope. Factory availability is historical, not current stock. No physical interchange test was performed.
Source: TI 22/2001, p. 7 · TI 22/2001, p. 9 · TI 22/2001, p. 10 — 6 shroud context;8 complete split summary and remarks.
Part numbers (5)
- 4134 140 0651 — Previous muffler-with-shroud setNo longer factory supplied · BT 120 C; stated configuration only
- 4134 140 0653 — New muffler-with-shroud setIncludes new shroud · BT 120 C; stated configuration only
- 4134 084 0907 — Previous shroudNo longer factory supplied · BT 120 C; stated configuration only
- 4134 080 1601 — New shroudIncludes label sheet · BT 120 C; stated configuration only
- 4134 967 1514 — Model-label sheetIncluded with shroud · BT 120 C; stated configuration only
Service note · BT 120 C
BT 120 C: engine, fuel and ignition specifications
30.8cm³, 1.3kW and a single-LD carburetor are historical 1998 specifications.
- Section2.1: displacement30.8cm³ (1.88cu.in), bore35mm (1.37in), stroke32mm (1.26in); power1.3kW (1.8bhp) to ISO8893. Single-pawl rewind starter with ElastoStart grip. Rope refers to section4; no rope dimension is supplied here.
- All-position diaphragm carburetor with integral fuel pump and ONE adjusting screw. Idle2800rpm; clutch engagement4300rpm. Fuel capacity0.64l (1.35USpt). Do not substitute later H/L/LA adjustments or interpret the engagement value as an idle target.
- Ignition module has integral electronic speed limiter. Suppressed spark plugs listed: Bosch WSR6F, NGK BPMR7A or Champion RCJ6Y. No plug gap, torque, ignition timing or mixture ratio is specified on this page; none is inferred.
- Historical BT 120 C only. TI37/1998 calls the machine series4313; the catalog groups its exact-model sheets under4134. Those identifiers are retained, not declared equivalent. Later carburetor/control revisions and BT121 are not included. No hardware operation was performed.
Source: TI 37/1998, p. 3 — Complete2.1.1–2.1.3.
No additional parts-table entry added.
Wrong number or missing part for the BT 120 C? Report a correction →