← Augers/Drills & other equipment · series 4134

Stihl 4134 · Section B · 2 of 12 · 34 parts

Rewind starter, Ignition system

Fits BT 120 C.

Parts diagrams →

Historical fitment & changes (6) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
1101112131415161718192202122222323242526262728293303132334456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (34)

PosPart numberDescriptionQty
1 4134 080 1801 Fan housing Fitment / change note → 1
2 1110 084 9102 Bushing 1
3 4134 190 0601 Rewind spring Fitment / change note → 1
4 9104 003 0410 Self-tapping screw P3x6 Fitment / change note → 2
5 4223 084 5600 Screw Fitment / change note → 1
6 4128 195 0400 Rope rotor 1
7 0000 190 3405 Starter grip ElastoStart Ø 3 mm Fitment / change note → 1
8 0000 195 8203 Starter rope Ø 3x850 mm Fitment / change note → 1
9 0000 195 7000 Cap 1
10 0000 195 7200 Pawl Fitment / change note → 1
11 0000 958 0923 Washer 1
12 1118 195 3500 Spring 1
13 4134 190 0600 NLA Rewind spring Fitment / change note → → replaced by 4134 190 0601 TI 22/2001 1
14 9099 021 2330 NLA Self-tapping screw 3.5x6.5 Fitment / change note → 1
15 0000 190 3400 Starter grip ElastoStart Ø 3 mm Fitment / change note → → replaced by 0000 190 3403, 0000 190 3403 TI 42/1999 1
16 0000 195 8200 Starter rope Ø 3x800 mm Fitment / change note → 1
17 4313 967 1501 Model plate BT 120 C 1
18 4134 400 1200 Flywheel 1
19 9220 260 1100 Hexagon nut M8 1
20 4134 400 1301 Ignition module Fitment / change note → 1
21 4137 442 0400 Insulating hose Fitment / change note → 1
22 0000 998 0604 Torsion spring Fitment / change note → 1
23 4128 405 1000 Spark plug boot Fitment / change note → 1
24 4134 400 1306 NLA Ignition module Fitment / change note → → replaced by 4134 400 1301 TI 22/2001 1
25 4134 028 1300 NLA Shim 10x15x4 Fitment / change note → 1
26 9075 478 3022 Pan head self-tapping screw IS-D4x20 2
27 9291 021 0121 Washer 5.3 Fitment / change note → 2
28 9291 021 0121 Washer 5.3 Fitment / change note → 2
29 4134 432 9300 Grommet 1
30 0000 951 1100 Screw IS-D5x20 4
31 4134 440 1101 Short circuit wire 1
32 4134 440 1100 NLA Short circuit wire 1
33 4134 448 1200 NLA Lead retainer 1
Not numbered on the diagram — assemblies, kits and options
— 4134 080 2101 NLA Fan housing with rewind starter Fitment / change note → 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Conditional replacement · BT 120 C / FS 120 / FS 200 / FS 250 / FS 350

TI09: spring-housing plastoform screw replacement

The new spring-housing screw may also be used in older listed machines.

  • Plastoform screw 9104 003 0410 has for some time replaced self-tapping screw 9099 021 2330 to fasten the spring housing inside the fan housing. The plastoform screw may also be used in older machines covered by this bulletin.
  • Diagram250TI060 identifies the fastening location; neither screw dimensions, torque nor a numeric changeover are supplied. For some time is not a production date. The page footer lists earlier TIs for FS 120/200/250, FS 350 and BT 120 C as bibliographic references, not additional service instructions.
  • Only the printed TI09/2003 models and described configurations are covered. Shared catalog sheets do not extend this assertion to FS 300, BT 121, SP 200, HT 250 or unlisted R variants. No physical interchange test was performed.

Source: TI 9/2003, p. 1 · TI 9/2003, p. 23 — 8 rewind starter/spring housing fastening; last-TI bibliography.

Part numbers (2)
  • 9099 021 2330 — Self-tapping spring-housing screwPrevious · TI09/2003 section 8 rewind starter/spring housing fastening; last-TI bibliography models/configurations only; preserve restrictions above
  • 9104 003 0410 — Plastoform spring-housing screwReplacement; older-machine use allowed · TI09/2003 section 8 rewind starter/spring housing fastening; last-TI bibliography models/configurations only; preserve restrictions above

Conditional replacement · FS 120 / FS 200 / FS 350 / BT 120 C

TI22: enclosed rewind spring requires its matching fan housing

Old and new housings/springs are not interchangeable; new spring uses 1.5 turns reserve pull.

  • Spring 4134 190 0600 becomes enclosed spring 4134 190 0601. Fan housing 4134 080 1800 becomes 4134 080 1801 with two mounting bosses; spring-housing screws 9099 021 2330 (3.5 x 6.5) increase from one to two. Tighten these spring-housing screws to 0.7 Nm only.
  • Old and new fan housings and rewind springs are NOT interchangeable. Replace the old 4134 080 2100 complete starter with new fan housing with rewind starter 4134 080 2101 when servicing older machines. Old bare/complete housings are supplied only while stocks last; old spring remains a spare, not a permitted mix with the new housing.
  • The starter post is shortened and spring-clip bearing groove is now in the head of replaceable annular-grooved screw 4223 084 5600. New spring with rope rotor needs reserve pull of 1.5 revolutions; previous spring remains at 0.5 revolution. Do not transfer either reserve setting to the other spring.
  • New housing takes neutral STIHL nameplate 0000 967 1500 or the new round model plate; model-plate changes are covered in the companion note. Summary identifies the old assembly as including items 4–7 and 9; new row prints "including items to 7 and 10" without a starting item. That incomplete contents phrase is retained, not repaired into a guaranteed kit roster. All listed model introductions are in progress.
  • TI22 describes an interdependent update package. Its introduction says most new parts were fitted to FS 250 from production start, with unspecified exceptions; this is not blanket FS 250 fitment approval. Shared sheets do not extend the named model/configuration scope. Factory availability is historical, not current stock. No physical interchange test was performed.

Source: TI 22/2001, p. 4 · TI 22/2001, p. 5 · TI 22/2001, p. 6 — 5.1–5.3 fan housing, starter post, spring and full summary context.

Part numbers (9)
  • 4134 190 0600 — Previous rewind spring0.5 revolution reserve · FS 120, FS 200, FS 350, BT 120 C; stated configuration only
  • 4134 190 0601 — Enclosed rewind spring1.5 revolutions reserve · FS 120, FS 200, FS 350, BT 120 C; stated configuration only
  • 4134 080 1800 — Previous bare fan housingOld system · FS 120, FS 200, FS 350, BT 120 C; stated configuration only
  • 4134 080 1801 — New fan housingMatched enclosed spring · FS 120, FS 200, FS 350, BT 120 C; stated configuration only
  • 4134 080 2100 — Previous housing with starterOld assembly · FS 120, FS 200, FS 350, BT 120 C; stated configuration only
  • 4134 080 2101 — New housing with starterReplacement for older machines · FS 120, FS 200, FS 350, BT 120 C; stated configuration only
  • 9099 021 2330 — Self-tapping 3.5 x 6.5 screwTwo; spring housing 0.7 Nm · FS 120, FS 200, FS 350, BT 120 C; stated configuration only
  • 4223 084 5600 — Annular-grooved-head screwNew starter-post screw · FS 120, FS 200, FS 350, BT 120 C; stated configuration only
  • 0000 967 1500 — Neutral STIHL nameplateNew housing option · FS 120, FS 200, FS 350, BT 120 C; stated configuration only

Conditional replacement · FS 120 / FS 200 / FS 350 / BT 120 C

TI22: longer starter rope is forbidden in the old starter

New 850 mm rope and ElastoStart are one-way compatible; new pawl can serve old starters.

  • Mini ElastoStart 0000 190 3400 with rope 0000 195 8200 (diameter 3.0 x 800 mm; 0.12 inch x 31.5 inch) changes to 0000 190 3405 with rope 0000 195 8203 (diameter 3.0 x 850 mm; 0.12 inch x 33.5 inch). Introduction is in progress.
  • The new longer rope and new ElastoStart MUST NOT be installed in previous starters: the source warns this would cause the rewind to break. Conversely, previous shorter rope and previous ElastoStart MAY be installed in the new starter. Old rope and ElastoStart remain spares; supply is not symmetric interchange approval.
  • New pawl 0000 195 7200 replaces 4116 195 7200 and has a metal guide peg for wear life. The new pawl may also be used in the previous starter. The old pawl remains available as a spare. These permissions do not remove the matched fan-housing/spring restriction.
  • TI22 describes an interdependent update package. Its introduction says most new parts were fitted to FS 250 from production start, with unspecified exceptions; this is not blanket FS 250 fitment approval. Shared sheets do not extend the named model/configuration scope. Factory availability is historical, not current stock. No physical interchange test was performed.

Source: TI 22/2001, p. 5 · TI 22/2001, p. 6 — 5.1.3–5.1.4;5.2.3–5.2.4;5.3 summary.

Part numbers (6)
  • 0000 190 3400 — Previous Mini ElastoStartOld/short-rope version · FS 120, FS 200, FS 350, BT 120 C; stated configuration only
  • 0000 190 3405 — New Mini ElastoStartForbidden in old starter · FS 120, FS 200, FS 350, BT 120 C; stated configuration only
  • 0000 195 8200 — 3.0 x 800 mm ropeOld; allowed in new starter · FS 120, FS 200, FS 350, BT 120 C; stated configuration only
  • 0000 195 8203 — 3.0 x 850 mm ropeNew; forbidden in old starter · FS 120, FS 200, FS 350, BT 120 C; stated configuration only
  • 4116 195 7200 — Previous pawlRemains spare · FS 120, FS 200, FS 350, BT 120 C; stated configuration only
  • 0000 195 7200 — Metal-guide-peg pawlAlso allowed in old starter · FS 120, FS 200, FS 350, BT 120 C; stated configuration only

Conditional replacement · FS 120 / FS 200 / FS 350 / BT 120 C

TI22: ignition module needs new shroud and conditional spacing washers

Protective-hose numbers conflict between the prose and summary; neither is silently preferred.

  • Ignition module 4134 400 1306 becomes 4134 400 1301. Previous support pad 4134 028 1300 is deleted from the new configuration; old module and pad remain spares for older machines. Spark-plug boot 4128 405 1000 and leg spring 0000 998 0604 retain their numbers. New module includes protective hose, boot and spring; old module includes boot and spring.
  • The new crankcase ignition mounting boss is 1 mm higher, identified by casting 4134 021 0760 C. With previous crankcase casting 4134 021 0760 and the new module, install an A 5.3 washer BETWEEN boss and core stack at BOTH mounting points. An A 5.3 washer is also required UNDER EACH SCREW HEAD in ALL cases. Summary calls 9291 021 0121 washer A5.3 (2x); that does not cancel the extra two spacing washers for an old crankcase.
  • The new module may ONLY be installed with new shrouds (section6 plus cooling dependencies in sections9/10). New shroud has the lead/hose cutout and no old model-plate seat; the drawing marks module 4134 1301 A, not an additional full order number.
  • Unresolved printed source conflict: page8 prose names protective hose 4134 442 0400, while page9 summary item3 names 4137 442 0400. Both scans confirm the different numbers. Neither is asserted as the uniquely correct replacement; verify the exact hose before ordering. Introduction follows section5.3, in progress, not a numeric cutoff.
  • TI22 describes an interdependent update package. Its introduction says most new parts were fitted to FS 250 from production start, with unspecified exceptions; this is not blanket FS 250 fitment approval. Shared sheets do not extend the named model/configuration scope. Factory availability is historical, not current stock. No physical interchange test was performed.

Source: TI 22/2001, p. 8 · TI 22/2001, p. 9 — 7 complete module/shroud drawings, service note and summary.

Part numbers (9)
  • 4134 400 1306 — Previous ignition moduleRemains spare for older machines · FS 120, FS 200, FS 350, BT 120 C; stated configuration only
  • 4134 400 1301 — New ignition moduleNew shroud and conditional spacing washers required · FS 120, FS 200, FS 350, BT 120 C; stated configuration only
  • 4134 028 1300 — Previous support padDeleted from new arrangement; remains spare · FS 120, FS 200, FS 350, BT 120 C; stated configuration only
  • 4128 405 1000 — Spark plug bootUnchanged · FS 120, FS 200, FS 350, BT 120 C; stated configuration only
  • 0000 998 0604 — Leg springUnchanged · FS 120, FS 200, FS 350, BT 120 C; stated configuration only
  • 9291 021 0121 — A 5.3 washerUnder heads always; extra spacers for old crankcase · FS 120, FS 200, FS 350, BT 120 C; stated configuration only
  • 4134 442 0400 — Protective hose: prose numberConflicts with summary; unresolved · FS 120, FS 200, FS 350, BT 120 C; stated configuration only
  • 4137 442 0400 — Protective hose: summary numberConflicts with prose; unresolved · FS 120, FS 200, FS 350, BT 120 C; stated configuration only
  • 4134 021 0760 — Crankcase casting identifier; new index CCasting, not replacement order number; controls spacing washers · FS 120, FS 200, FS 350, BT 120 C; old/new crankcase context

Service note · BT 120 C

BT 120 C: engine, fuel and ignition specifications

30.8cm³, 1.3kW and a single-LD carburetor are historical 1998 specifications.

  • Section2.1: displacement30.8cm³ (1.88cu.in), bore35mm (1.37in), stroke32mm (1.26in); power1.3kW (1.8bhp) to ISO8893. Single-pawl rewind starter with ElastoStart grip. Rope refers to section4; no rope dimension is supplied here.
  • All-position diaphragm carburetor with integral fuel pump and ONE adjusting screw. Idle2800rpm; clutch engagement4300rpm. Fuel capacity0.64l (1.35USpt). Do not substitute later H/L/LA adjustments or interpret the engagement value as an idle target.
  • Ignition module has integral electronic speed limiter. Suppressed spark plugs listed: Bosch WSR6F, NGK BPMR7A or Champion RCJ6Y. No plug gap, torque, ignition timing or mixture ratio is specified on this page; none is inferred.
  • Historical BT 120 C only. TI37/1998 calls the machine series4313; the catalog groups its exact-model sheets under4134. Those identifiers are retained, not declared equivalent. Later carburetor/control revisions and BT121 are not included. No hardware operation was performed.

Source: TI 37/1998, p. 3 — Complete2.1.1–2.1.3.

No additional parts-table entry added.

Service note · BT 120 C

BT 120 C: extension, chuck, padding and starter accessories

Six accessory/lubricant rows retain their separate applications.

  • Section4: shank extension4311 680 2350 extends auger; no extension length stated. Chuck4311 680 4010 is for drills UP TO13mm (0.5in) diameter; padding4311 748 2500 cushions the user’s thigh. No extra cutting capacity or unrestricted extension stacking is implied.
  • ElastoStart0000 190 3400 is the rewind-starter GRIP WITH ROPE;0000 195 8200 is rope alone. STIHL gear lubricant0781 120 1117 is an80g/3oz TUBE for the gearbox; package size is not a gearbox fill quantity or service interval.
  • Historical BT 120 C only. TI37/1998 calls the machine series4313; the catalog groups its exact-model sheets under4134. Those identifiers are retained, not declared equivalent. Later carburetor/control revisions and BT121 are not included. No hardware operation was performed.

Source: TI 37/1998, p. 4 — Complete section4.

Part numbers (6)
  • 4311 680 2350 — Shank extensionHistorical specified item · BT 120 C; TI37/1998 configuration only
  • 4311 680 4010 — Chuck for drills up to13mmHistorical specified item · BT 120 C; TI37/1998 configuration only
  • 4311 748 2500 — Thigh paddingHistorical specified item · BT 120 C; TI37/1998 configuration only
  • 0000 190 3400 — ElastoStart grip with ropeHistorical specified item · BT 120 C; TI37/1998 configuration only
  • 0000 195 8200 — ElastoStart ropeHistorical specified item · BT 120 C; TI37/1998 configuration only
  • 0781 120 1117 — STIHL gear lubricant80g/3oz tubeHistorical specified item · BT 120 C; TI37/1998 configuration only

Wrong number or missing part for the BT 120 C? Report a correction →