← Augers/Drills & other equipment · series 4134

Stihl 4134 · Section H · 8 of 12 · 13 parts

Gear head

Fits BT 120 C.

Parts diagrams →

Historical fitment & changes (2) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
11011121322334567789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (13)

PosPart numberDescriptionQty
1 4313 641 0300 Gear housing 1
2 4600 641 4900 Sleeve 2
3 9503 003 0510 Grooved ball bearing 6004 2
4 4119 713 6500 Screw plug 1
5 4313 642 0100 Spur gear 1
6 4313 642 2500 Drive pinion shaft 1
7 9022 341 1070 Spline screw IS-M5x30 3
8 4313 642 0105 Spur gear 1
9 4313 642 0600 Drive shaft 1
10 9630 003 3616 Oil seal 35x20x7 1
11 9503 003 6320 Grooved ball bearing 6200 1
12 4311 641 0400 Cover 1
13 9022 341 1110 Spline screw IS-M5x52 4

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · BT 120 C

BT 120 C: rated speeds, gearbox and spindle torque

The no-auger cutoff, rated spindle speed and maximum torque are distinct source values.

  • Section2.1.2 lists rated cutoff12300rpm WITHOUT AUGER, with electronic speed limiter, and maximum rated spindle speed190rpm. Section2.2 gives47.5:1 gearbox ratio. The source does not give a common operating/load condition relating those values; do not derive or replace spindle speed by dividing the no-auger cutoff by the ratio.
  • Section2.3 maximum drilling-spindle torque79Nm (58ft.lb) is an OUTPUT specification, NOT a fastener tightening torque. Section2.4 weight8.2kg (18.1lb) WITHOUT AUGER. No installed-auger weight or measured performance is claimed.
  • Historical BT 120 C only. TI37/1998 calls the machine series4313; the catalog groups its exact-model sheets under4134. Those identifiers are retained, not declared equivalent. Later carburetor/control revisions and BT121 are not included. No hardware operation was performed.

Source: TI 37/1998, p. 3 — 2.1.2 rated speeds and complete2.2–2.4.

No additional parts-table entry added.

Service note · BT 120 C

BT 120 C: gear repair times and engine-table delegation

Seven gear-table rows retain the dash and trained-workshop assumptions.

  • Section6.4 assumes TRAINED PERSONNEL in a PROPERLY EQUIPPED SERVICE WORKSHOP. Values are tenths of an hour;0.1=6minutes. The BT120C table may be added to the STIHL repair-times table; these are historical labor allowances, not owner repair-time guarantees.
  • Code1 Gear Unit: DASH (no numeric allowance, not zero). Code2 Gear Unit Housing0.6h;3 Bearings1.0h;4 Grease Seals0.5h;5 Pinion Shaft0.4h;6 Spur Gear & Driver0.5h;20 Misc. Repairs0.5h. Seven printed codes, six numeric allowances; no totals, missing codes7–19 or bundled overlapping work are invented.
  • The BT120C asterisk directs ENGINE repair times to the FS120 brushcutter table. Later2012-01 FS120 engine and BT120/121 tables are now reviewed separately with minute units, changed repair codes, blank cells and stop-switch20/25min difference preserved; the exact historical1998 FS120 table remains a documented retained-corpus source gap. Footer identifies1998 copyright and document6381, not an IPL edition.
  • Historical BT 120 C only. TI37/1998 calls the machine series4313; the catalog groups its exact-model sheets under4134. Those identifiers are retained, not declared equivalent. Later carburetor/control revisions and BT121 are not included. No hardware operation was performed.

Source: TI 37/1998, p. 6 — Complete6.4 table, asterisk and footer.

No additional parts-table entry added.

Wrong number or missing part for the BT 120 C? Report a correction →