Stihl 4134 · Section J · 9 of 12 · 25 parts
Handlebar, Control handle
Fits BT 120 C.
Historical fitment & changes (6) — includes parts and conditions not shown on this drawing.
Parts (25)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4313 790 1703 | Handlebar | 1 |
| 2 | 4313 790 1704 NLA | Handlebar | 1 |
| 3 | 4313 791 1701 | Handlebar | 1 |
| 4 | 9022 341 1070 | Spline screw IS-M5x30 | 2 |
| 5 | 9216 263 0700 | Hexagon nut M5 → replaced by 9220 260 0701 TI 25/1994 | 2 |
| 6 | 0000 967 3703 | Warning pictogram BT | 1 |
| 7 | 4311 967 3500 NLA | Instruction label | 1 |
| 8 | 4313 791 0300 | Handle, left | 1 |
| 9 | 4137 790 0300 | Handle Fitment / change note → | 1 |
| 10 | 4137 791 9400 | Hose clamp | 2 |
| 11 | 9022 341 0960 | Spline screw IS-M5x12 → replaced by 9022 341 0980 TI 3/2006 | 2 |
| 12 | 4137 182 4505 | Torsion spring Fitment / change note → | 1 |
| 13 | 4137 182 1701 | Slide control Fitment / change note → | 1 |
| 14 | 4137 182 1001 | Throttle trigger Fitment / change note → | 1 |
| 15 | 4137 182 4504 | Torsion spring Fitment / change note → | 1 |
| 16 | 4137 182 0802 | Lockout lever Fitment / change note → | 1 |
| 17 | 4128 182 4501 | Torsion spring Fitment / change note → | 1 |
| 18 | 4128 793 3000 | Slide Fitment / change note → | 1 |
| 19 | 4128 791 3100 | Spring Fitment / change note → | 1 |
| 20 | 9074 478 3025 | Pan head self-tapping screw IS-P4x16 | 4 |
| 21 | 4313 180 1102 | Throttle cable Fitment / change note → | 1 |
| 22 | 4313 182 3200 | Throttle cable | 1 |
| 23 | 9022 341 1310 | Spline screw IS-M6x18 | 4 |
| 24 | 0751 010 7056 | Cable tie | 2 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 4137 790 1307 | Control handle Fitment / change note → | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · FS 120 R / FS 200 R / FS 250 R / BT 120 C
TI09: loop-handle wiring, spring and 5 Nm clamp torque
Keep both wires inside the channel; the straight spring end goes under the cable sleeve.
- Page 6 names FS 120 R, FS 200 R and FS 250 R for the loop handle, and lists BT 120 C with the same control-handle assembly. This note covers those stated configurations, not every base model in a shared sheet.
- Seat microswitch 7 as drawn. Push ground wire 8 into channel 10 FIRST, then short-circuit wire 9. Both wires must remain in the channel right to the end of the handle; neither may project. Lay them in recess 20 at corrugated-tube attachment 19. Source says the throttle is placed over this recess in a later step; the illustrations retain the actual route.
- Press cable 11 into slide 12 until ferrule 13 snaps in; put the slide groove at the end of the slot. Attach bent sleeve 14 to trigger 15. Push straight spring end 16 UNDER sleeve 14, fit its ring over trigger pivot 17 and its loop around screw boss 18. Do not copy the bike-handle in-front-of-sleeve spring position.
- Check corrugated tube and slide position; do NOT squeeze the trigger before 1.12.5. Close moldings without pinching wires, connect cable at carburetor or check its pin seating, reassemble powerhead, slide control handle onto drive tube and secure drive tube to powerhead. Align and secure control handle; tighten its hose-clamp screws to 5 Nm (44 in/lbs.). This is not a torque for housing screws, carburetor nuts or bike-handle bolts. The 5 Nm value applies to the described drive-tube hose clamp, not an unspecified BT 120 C mounting fastener.
- Page 11 prints cable-pin reference 1.11.2, while the actual installation heading is 1.12.2; retain the numbering error. Continue with the fully assembled-machine cable adjustment below; this does not resolve the separate pin-direction ambiguity.
- Only the stated TI09 model and handle configurations with the new two-wire microswitch/cable and slide adjuster are covered. Shared sheets do not extend this to FS 300, BT 121 or other unnamed variants. This assembly/adjustment note is not a complete older-machine conversion; TI22/2001 and the remaining control roster and retrofit dependencies are still actionable. No physical interchange test was performed.
Source: TI 9/2003, p. 6 · TI 9/2003, p. 10 · TI 9/2003, p. 11 — 1.10 explicit loop-handle/BT model grouping;1.12.4 complete loop-handle assembly.
No additional parts-table entry added.
Service note · FS 120 / FS 200 / FS 250 / FS 350 / FS 120 R / FS 200 R / FS 250 R / BT 120 C
TI09: slide-adjuster reset and fully assembled-machine adjustment
Reset to the end of the slot, then operate interlock and full trigger travel once assembled.
- Adjust only with machine COMPLETELY and securely assembled and handlebar/control handle in NORMAL OPERATING position. This removes cable free play and is required for correct full-throttle, starting-throttle and idle operation. A transport-position setting is not equivalent.
- Readjust after accidental early trigger squeezing during handling or installation; after servicing or repair; before readjusting carburetor; during new-machine setup; after a large bike-handle position change such as transport versus operating position; or after cable stretch or a slide position change from snagging during operation. Do not reduce this list to a one-time factory adjustment.
- Use screwdriver to press down slide 12 and push it to the END of the slot, the basic setting shown by diagram 393TI054. Then press trigger interlock 21 and squeeze trigger 15 fully: slide 12 moves away from the end position and cable adjusts automatically. Adjust carburetor if necessary. The source does not instruct starting the engine to perform this reset and supplies no cable free-play dimension.
- The handle-assembly pages warn not to squeeze the trigger earlier. Follow the bike- or loop-handle assembly instructions and cable/pin seating prerequisites before this adjustment; automatic adjustment does not prove safe mechanical interchange.
- Only the stated TI09 model and handle configurations with the new two-wire microswitch/cable and slide adjuster are covered. Shared sheets do not extend this to FS 300, BT 121 or other unnamed variants. This assembly/adjustment note is not a complete older-machine conversion; TI22/2001 and the remaining control roster and retrofit dependencies are still actionable. No physical interchange test was performed.
Source: TI 9/2003, p. 6 · TI 9/2003, p. 11 — 1.12.5 all-model slide adjustment with1.10 explicit loop-handle scope.
No additional parts-table entry added.
Service note · FS 120 / FS 200 / FS 250 / FS 350 / FS 120 R / FS 200 R / FS 250 R / BT 120 C
TI 09: new control handles use a sealed switch and cable adjuster
The slide-slot identifies the new handle; cable and handle remain separate replacement assemblies.
- The new package covers control handle, throttle cable, retainer, retainer-to-ignition short-circuit wire, carburetor housing, contact plate/gasket changes and carburetor cable pin. The new carburetor is introduced concurrently. New versions may ONLY be installed as a complete matched assembly in previous machines, not as arbitrary individual substitutions. The required pin depends on the existing carburetor/cable combination.
- Control handle and throttle-cable assembly are supplied separately. The cable assembly consists of corrugated hose, cable, and sealed microswitch permanently connected to two fully insulated short-circuit wires running to retainer connectors. New cables install only as assemblies; do not invent separate microswitch/cable order numbers.
- New control handles have a semi-automatic adjuster identified by the slide slot (1); grey areas in drawing393TI042 are non-slip surfaces, not extra parts. Slide control (2) operates the sealed ignition microswitch. Bike and loop handles are distinct despite this shared design.
- At the prescribed adjustment, one FULL trigger squeeze removes slack between trigger and carburetor cable attachment points. The sheath end is attached to slide (1); it pulls toward the trigger while spring-loaded detent arm moves along the notched track until free play is removed. This describes the mechanism, not permission to actuate before assembly: follow the already reviewed section 1.12.5 procedure only after complete assembly and operating-position setup.
- Adjustment is needed after first-time handle/cable installation and may be needed during new-machine setup, especially after bike handlebars are fitted. Section 1.12.5 governs later readjustments; the adjustment chapter is added to the user instruction manual.
- USA production introduction is in progress, without a numeric cutoff. Factory availability describes the bulletin date, not current stock. Shared catalog sheets do not extend the stated model/handle/configuration scope. No physical interchange test was performed.
Source: TI 9/2003, p. 1 · TI 9/2003, p. 2 · TI 9/2003, p. 3 · TI 9/2003, p. 7 — 1 introduction/interchangeability;1.1–1.2.2;1.10 introduction.
No additional parts-table entry added.
Conditional replacement · FS 120 R / FS 200 R / FS 250 R / BT 120 C
TI 09: loop-handle and BT 120 C share controls, not throttle cables
The FS R variants and auger use handle1307 with specific springs, trigger and interlock.
- For FS 120 R/200R/250R and BT 120 C, handle 4137 790 1350 becomes 4137 790 1307. Old assembly includes items 28, 29, 31, 32, 34–36; new includes18, 19, 30, 31, 33–37. BT 120 C repeats these identical handle contents, NOT the FS throttle-cable number.
- Old inner molding 4137 790 1101 and outer molding 4137 791 0800 give way to handle 4137 790 0300. Slide control 4137 182 1700 becomes 4137 182 1701; old contact spring 4137 442 1600 is removed. New torsion spring 4137 182 4505 is item 33.
- Trigger 4137 182 1000 becomes 4137 182 1001; torsion spring 4137 182 4500 becomes 4137 182 4504; interlock lever 4137 182 0801 becomes 4137 182 0802. Added torsion spring 4128 182 4501 is item 37. New assembly also includes shared adjuster slide 4128 793 3000 and spring 4128 791 3100. Do not interchange the three different torsion springs by generic name.
- Previous parts marked remark 1 remain available for older machines; all other parts remain as before. Control and cable are separate replacement assemblies. FS 350 loop-handle applicability is NOT stated in this roster.
- USA production introduction is in progress, without a numeric cutoff. Factory availability describes the bulletin date, not current stock. Shared catalog sheets do not extend the stated model/handle/configuration scope. No physical interchange test was performed.
Source: TI 9/2003, p. 2 · TI 9/2003, p. 6 · TI 9/2003, p. 7 — 1.1;1.10 items26–44 with remarks.
Part numbers (18)
- 4137 790 1350 — Previous complete control handleOlder-machine spare · FS 120 R, FS 200 R, FS 250 R, BT 120 C; stated configuration only
- 4137 790 1307 — New complete control handleFS R variants and BT 120 C · FS 120 R, FS 200 R, FS 250 R, BT 120 C; stated configuration only
- 4137 790 1101 — Old inner handle moldingOlder-machine spare · FS 120 R, FS 200 R, FS 250 R, BT 120 C; stated configuration only
- 4137 791 0800 — Old outer handle moldingOlder-machine spare · FS 120 R, FS 200 R, FS 250 R, BT 120 C; stated configuration only
- 4137 790 0300 — New handleNew · FS 120 R, FS 200 R, FS 250 R, BT 120 C; stated configuration only
- 4137 182 1700 — Old slide controlOlder-machine spare · FS 120 R, FS 200 R, FS 250 R, BT 120 C; stated configuration only
- 4137 182 1701 — New slide controlNew · FS 120 R, FS 200 R, FS 250 R, BT 120 C; stated configuration only
- 4137 442 1600 — Old contact springOlder-machine spare; deleted from new · FS 120 R, FS 200 R, FS 250 R, BT 120 C; stated configuration only
- 4137 182 4505 — Torsion spring item 33New · FS 120 R, FS 200 R, FS 250 R, BT 120 C; stated configuration only
- 4137 182 1000 — Old throttle triggerOlder-machine spare · FS 120 R, FS 200 R, FS 250 R, BT 120 C; stated configuration only
- 4137 182 1001 — New throttle triggerNew · FS 120 R, FS 200 R, FS 250 R, BT 120 C; stated configuration only
- 4137 182 4500 — Old torsion spring item 35Older-machine spare · FS 120 R, FS 200 R, FS 250 R, BT 120 C; stated configuration only
- 4137 182 4504 — New torsion spring item 35New · FS 120 R, FS 200 R, FS 250 R, BT 120 C; stated configuration only
- 4137 182 0801 — Old interlock leverOlder-machine spare · FS 120 R, FS 200 R, FS 250 R, BT 120 C; stated configuration only
- 4137 182 0802 — New interlock leverNew · FS 120 R, FS 200 R, FS 250 R, BT 120 C; stated configuration only
- 4128 182 4501 — Torsion spring item 37New · FS 120 R, FS 200 R, FS 250 R, BT 120 C; stated configuration only
- 4128 793 3000 — Adjuster slide item 18New · FS 120 R, FS 200 R, FS 250 R, BT 120 C; stated configuration only
- 4128 791 3100 — Adjuster spring item 19New · FS 120 R, FS 200 R, FS 250 R, BT 120 C; stated configuration only
Conditional replacement · FS 120 / FS 200 / FS 250 / FS 350 / FS 120 R / FS 200 R / FS 250 R / BT 120 C
TI 09: cable assemblies keep distinct 690, 185 and 545 mm hoses
The spare-hose remarks contain broken item references; no collar screw is treated as hose.
- BIKE-HANDLED FS 120/200/250/350: cable assembly 4128 180 1102 (items 22, 24) becomes 4128 180 1104 (items 22–24) with 690 mm hose. LOOP-HANDLED FS 120 R/200R/250R: 4134 180 1107 (items 40, 42) becomes 4134 180 1103 (items 40–42) with 185 mm hose. BT 120 C: 4313 180 1100 (items 47, 49) becomes 4313 180 1102 (items 47–49) with 545 mm hose.
- Each new assembly adds microswitch with short-circuit wires. Previous assemblies remain older-machine spares. Individual old cable/hose components were not supplied separately (remark 2); new individual cable, microswitch/wires and cut hose are not supplied separately (remark 3). Asterisks are non-orderable placeholders, not part numbers. The separately identified spare hose is the explicit cutting-stock exception.
- Item 25 names960 mm spare hose 4203 711 7201, with a dash in the New column; remark 5 nevertheless says to use it instead of the hoses in items 24, 42, 49 and57. The690/185/545 mm lengths belong to the three named assemblies, NOT to a single interchangeable complete cable.
- Documented source error: remark 4 says cut from spare hose at items 25 OR50, but item 50 is a COLLAR SCREW. Remark 5 also refers to item 57, which does not exist in this section (ends at50). Item 25 is the named spare hose; do not fabricate another hose number or an item 57 application. Preserve the erroneous references, without treating screw 0000 711 8700 as cutting stock.
- USA production introduction is in progress, without a numeric cutoff. Factory availability describes the bulletin date, not current stock. Shared catalog sheets do not extend the stated model/handle/configuration scope. No physical interchange test was performed.
Source: TI 9/2003, p. 2 · TI 9/2003, p. 6 · TI 9/2003, p. 7 — 1.2;1.10 items20–25,38–42,45–50 and all remarks.
Part numbers (7)
- 4128 180 1102 — Throttle-cable assemblyPrevious; older-machine spare · FS 120/200/250/350; bike handle
- 4128 180 1104 — Throttle-cable assemblyNew; includes microswitch/wires · FS 120/200/250/350; bike handle
- 4134 180 1107 — Throttle-cable assemblyPrevious; older-machine spare · FS 120 R/200R/250R; loop handle
- 4134 180 1103 — Throttle-cable assemblyNew; includes microswitch/wires · FS 120 R/200R/250R; loop handle
- 4313 180 1100 — Throttle-cable assemblyPrevious; older-machine spare · BT 120 C only
- 4313 180 1102 — Throttle-cable assemblyNew; includes microswitch/wires · BT 120 C only
- 4203 711 7201 — 960 mm spare hoseCut to specified assembly length; broken cross-references retained · FS 120, FS 200, FS 250, FS 350, FS 120 R, FS 200 R, FS 250 R, BT 120 C; stated configuration only
Conditional replacement · BT 120 C
BT 120 C: shorter collar-screw thread improves cable routing
New collar screw has 20 mm plastoform thread and may also serve older BT 120 C machines.
- BT 120 C ONLY: collar screw 4313 711 8700 fastening clutch housing to crankcase becomes 0000 711 8700. The plastoform thread shortens by 4 mm, from 24 mm (0.944 inch) to 20 mm (0.787 inch), to optimize cable routing. Drawing427TI000 measures the plastoform portion to the shoulder, not overall screw length.
- New screw may also be used in older BT 120 C machines. Previous screw is supplied only while existing stocks last (remark 6), unlike the many other older parts retained as spares by remark 1. Item 50 is this screw, despite the erroneous spare-hose cross-reference. No FS-model screw substitution is authorized by this BT 120 C-only instruction.
- USA production introduction is in progress, without a numeric cutoff. Factory availability describes the bulletin date, not current stock. Shared catalog sheets do not extend the stated model/handle/configuration scope. No physical interchange test was performed.
Source: TI 9/2003, p. 5 · TI 9/2003, p. 7 — 1.9 full dimensioned drawing;1.10 item50 and remark6.
Part numbers (2)
- 4313 711 8700 — Old24 mm-thread collar screwStocks only · BT 120 C; stated configuration only
- 0000 711 8700 — New20 mm-thread collar screwAlso permitted on older BT 120 C · BT 120 C; stated configuration only
Wrong number or missing part for the BT 120 C? Report a correction →