Stihl 4134 · Section K · 10 of 18 · 19 parts
Clutch housing
Fits FS 120, FS 120 R, FS 200, FS 200 R, FS 250, FS 250 R.
Historical fitment & changes (3) — includes parts and conditions not shown on this drawing.
Parts (19)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4134 160 0601 | Clutch housing | 1 |
| 2 | 9503 003 7450 | Grooved ball bearing 6202-2RS | 1 |
| 3 | 9456 621 3860 | Circlip 35x1.5 | 1 |
| 4 | 4128 160 2001 | Clutch Fitment / change note → | 1 |
| 5 | not sold separately | Clutch shoe not available as a separate item | 2 |
| 6 | 0000 961 0608 | Ring | 2 |
| 7 | 0000 951 0606 | Hexagon head screw | 2 |
| 8 | 0000 997 5519 | Tension spring | 2 |
| 9 | 4128 162 1000 | Cover washer | 1 |
| 10 | 0000 958 1000 | Washer 16x10x0.5 Fitment / change note → | 2 |
| 11 | 4134 160 2900 | Clutch drum | 1 |
| 12 | 9455 621 1520 | Circlip 15x1 | 1 |
| 13 | 9075 478 4175 | Pan head self-tapping screw IS-D5x28 | 4 |
| 14 | 4134 160 0400 | Clutch shroud Fitment / change note → | 1 |
| 15 | 4137 791 9300 | Rubber insert | 1 |
| 16 | 9457 621 4481 | Circlip | 1 |
| 17 | 4137 790 7200 | Sleeve | 1 |
| 18 | 9075 478 4095 | Pan head self-tapping screw IS-D5x12 | 1 |
| 19 | 9022 371 1020 | Spline screw IS-M5x20 → replaced by 9022 371 1050 TI 30/2004 | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Conditional replacement · BT 120 C / FS 120 / FS 200 / FS 250 / FS 350
TI09: clutch washers require the new matched assembly
Do not fit the new washers to the old clutch or mix old/new carriers and shoes.
- Clutch 4128 160 2000 was replaced by 4128 160 2001 for quieter operation. The new clutch has two washers 0000 958 1000, 16 x 10 x 0.5 mm, one at each bearing point between carrier and clutch shoe.
- The washers must NOT be installed in the previous clutch. Old and new carriers and shoes must not be combined for dimensional reasons. The table phrase all other parts as before does not override this prohibition.
- The source recommends replacing the previous clutch with the complete new assembly rather than replacing its individual parts. Only new clutch 4128 160 2001 is available from the factory; the old assembly is no longer supplied. This is historical factory availability, not current stock verification.
- The summary gives USA production from serial 2 52 747 650. It does not assign a separate serial to each heading model, establish a worldwide cutoff or define a model production range. Keep this as a USA clutch-change statement, not a crankshaft or seal cutoff.
- Only the printed TI09/2003 models and described configurations are covered. Shared catalog sheets do not extend this assertion to FS 300, BT 121, SP 200, HT 250 or unlisted R variants. No physical interchange test was performed.
Source: TI 9/2003, p. 1 · TI 9/2003, p. 21 — 5 clutch, illustration and complete summary.
Part numbers (3)
- 4128 160 2000 — Previous clutch assemblyReplaced; no longer factory supplied · TI09/2003 section 5 clutch, illustration and complete summary models/configurations only; preserve restrictions above
- 4128 160 2001 — New clutch assemblyUse matched carrier and shoes · TI09/2003 section 5 clutch, illustration and complete summary models/configurations only; preserve restrictions above
- 0000 958 1000 — Washer16x10x0.5Two; new clutch only · TI09/2003 section 5 clutch, illustration and complete summary models/configurations only; preserve restrictions above
Conditional replacement · FS 120 / FS 200
FS 120/200: new cylinder shroud requires index-C clutch shroud
Order number stays unchanged; index B is restricted to previous machines.
- The new clutch shroud has an added cooling-air chamber, illustrated by the arrow and casting number 4134 161 0400 C. Order number remains 4134 160 0400; casting identifier and order number are different, and the unchanged order number alone cannot identify the revision.
- When fitting a new cylinder shroud on an older FS 120/200, also install index-C clutch shroud. Index B may ONLY be used in previous machine versions. Index C can be combined with new OR previous cylinder shrouds. Introduction is in progress; only the modified version is factory supplied.
- TI22 describes an interdependent update package. Its introduction says most new parts were fitted to FS 250 from production start, with unspecified exceptions; this is not blanket FS 250 fitment approval. Shared sheets do not extend the named model/configuration scope. Factory availability is historical, not current stock. No physical interchange test was performed.
Source: TI 22/2001, p. 10 — 9 full illustration, service note, summary and remarks.
Part numbers (2)
- 4134 160 0400 — Clutch shroudUnchanged order number; index restriction · FS 120, FS 200; stated configuration only
- 4134 161 0400 — Clutch-shroud casting identifierC index in diagram; not order number · FS 120, FS 200; stated configuration only
Service note · FS 120 / FS 200 / FS 350 / FS 400 / FS 450
FS120/200/350/400/450: clutch and rigid-shaft construction
Two unlined clutch shoes;4,300 rpm engagement is not idle or cut-off speed.
- Clutch uses TWO LARGE-DIAMETER SHOES WITHOUT LININGS. The rigid drive shaft is supported in a FULL-LENGTH LINER. Neither description supplies part numbers, wear limits, lubrication intervals or a shaft conversion.
- Every engine-table column gives clutch engagement at4,300 rpm. Do not confuse that value with2,800 rpm idle, electronic cut-off without a cutting tool, or the rated output-shaft speed. No field clutch test was performed.
- Historical TI42/1997 configurations only, not all later versions sharing a model name. No hardware operation was performed. No part interchange or numeric serial cutoff is established.
Source: TI 42/1997, p. 3 — Section1 clutch/shaft; section2.1.1 clutch row.
No additional parts-table entry added.
Wrong number or missing part for the FS 120, FS 120 R, FS 200, FS 200 R, FS 250, FS 250 R? Report a correction →