Stihl 4134 · Section H · 8 of 14 · 37 parts
Clutch housing, Drive tube assembly
Fits FS 300, FS 350.
Historical fitment & changes (4) — includes parts and conditions not shown on this drawing.
Parts (37)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4134 160 0603 | Clutch housing Fitment / change note → | 1 |
| 2 | 9503 003 7450 | Grooved ball bearing 6202-2RS | 1 |
| 3 | 9456 621 3860 | Circlip 35x1.5 | 1 |
| 4 | 4134 161 1200 | Cover Fitment / change note → | 1 |
| 5 | 9075 478 4718 | Pan head self-tapping screw IS-D6x32 Fitment / change note → | 1 |
| 6 | 9291 021 0140 | Washer 6.4 Fitment / change note → | 1 |
| 7 | 9075 478 4159 | Pan head self-tapping screw IS-D5x24 Fitment / change note → | 1 |
| 8 | 4128 160 2001 | Clutch Fitment / change note → | 1 |
| 9 | not sold separately | Clutch shoe not available as a separate item | 2 |
| 10 | 0000 961 0608 | Ring | 2 |
| 11 | 0000 997 5519 | Tension spring | 2 |
| 12 | 4128 162 1000 | Cover washer | 1 |
| 13 | 0000 951 0606 | Hexagon head screw | 2 |
| 14 | 0000 958 1000 | Washer 16x10x0.5 Fitment / change note → | 2 |
| 15 | 4128 160 2900 | Clutch drum | 1 |
| 16 | 9455 621 1520 | Circlip 15x1 | 1 |
| 17 | 9075 478 4159 | Pan head self-tapping screw IS-D5x24 Fitment / change note → | 4 |
| 19 | 4134 710 7109 | Drive tube assembly Ø 28 mm / 1 1/8'' | 1 |
| 20 | not sold separately | Flexible liner 1365 mm / 53 3/4'' not available as a separate item | 1 |
| 21 | 4128 711 7301 | Flexible liner 1425 mm / 56 1/8'' option | 1 |
| 22 | 4134 711 7300 NLA | Flexible liner 1440 mm / 56 3/4'' Fitment / change note → | 1 |
| 23 | 4128 711 2100 | Plug | 1 |
| 24 | 0000 967 3725 | Warning pictogram FS | 1 |
| 25 | 0000 967 3684 | Warning pictogram FS Fitment / change note → | 1 |
| 26 | 4134 711 2100 NLA | Plug Fitment / change note → | 1 |
| 27 | 4134 711 3200 | Drive shaft | 1 |
| 28 | 4128 790 0950 | AV housing | 1 |
| 29 | 4128 791 9800 | Square nut | 1 |
| 30 | 4128 792 9300 | Rubber buffer | 4 |
| 31 | 4128 790 7650 | Support | 1 |
| 32 | 4128 710 6700 | Hose clamp | 1 |
| 33 | 9022 341 1010 | Spline screw IS-M5x18 | 1 |
| 34 | 9291 021 0140 | Washer 6.4 Fitment / change note → | 1 |
| 35 | 9022 341 1350 | Spline screw IS-M6x25 | 1 |
| 36 | 9214 320 0900 | Lock nut M6 | 1 |
| 37 | 4128 791 7500 | Cover | 1 |
| 38 | 4128 792 2400 | Lead retainer | 2 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Conditional replacement · BT 120 C / FS 120 / FS 200 / FS 250 / FS 350
TI09: clutch washers require the new matched assembly
Do not fit the new washers to the old clutch or mix old/new carriers and shoes.
- Clutch 4128 160 2000 was replaced by 4128 160 2001 for quieter operation. The new clutch has two washers 0000 958 1000, 16 x 10 x 0.5 mm, one at each bearing point between carrier and clutch shoe.
- The washers must NOT be installed in the previous clutch. Old and new carriers and shoes must not be combined for dimensional reasons. The table phrase all other parts as before does not override this prohibition.
- The source recommends replacing the previous clutch with the complete new assembly rather than replacing its individual parts. Only new clutch 4128 160 2001 is available from the factory; the old assembly is no longer supplied. This is historical factory availability, not current stock verification.
- The summary gives USA production from serial 2 52 747 650. It does not assign a separate serial to each heading model, establish a worldwide cutoff or define a model production range. Keep this as a USA clutch-change statement, not a crankshaft or seal cutoff.
- Only the printed TI09/2003 models and described configurations are covered. Shared catalog sheets do not extend this assertion to FS 300, BT 121, SP 200, HT 250 or unlisted R variants. No physical interchange test was performed.
Source: TI 9/2003, p. 1 · TI 9/2003, p. 21 — 5 clutch, illustration and complete summary.
Part numbers (3)
- 4128 160 2000 — Previous clutch assemblyReplaced; no longer factory supplied · TI09/2003 section 5 clutch, illustration and complete summary models/configurations only; preserve restrictions above
- 4128 160 2001 — New clutch assemblyUse matched carrier and shoes · TI09/2003 section 5 clutch, illustration and complete summary models/configurations only; preserve restrictions above
- 0000 958 1000 — Washer16x10x0.5Two; new clutch only · TI09/2003 section 5 clutch, illustration and complete summary models/configurations only; preserve restrictions above
Conditional replacement · FS 350
FS 350: reinforced drive tube and shorter liner
A 90 mm steel sleeve replaces the lower plug; liner and tube dimensions stay model-specific.
1 49 513 615 — From this serial for the explicitly named component and model only; not a whole-model production range.
- A 90 mm (3 1/2 inch) steel sleeve is installed at the lower end of the 28 mm / 1.1 inch drive tube to strengthen the gearhead-clamp area. The lower plug is deleted; plug 4134 711 2100 stays under the same number but quantity falls from two to one. Illustration labels tube 1, steel sleeve 2 and liner 3; no separate sleeve order number is supplied.
- Tube 4134 710 7103 becomes 4134 710 7106; flexible liner changes from 4134 711 7300, 1440 mm (56 11/16 inch), to 4134 711 7302, 1365 mm (53 3/4 inch). Instruction label 0000 967 3684 is unchanged. The summary includes liner, plug and label with the tube.
- FS 350 introduction is from serial 1 49 513 615; previous tube is supplied only while stocks last, but previous liner remains a spare.
- TI22 describes an interdependent update package. Its introduction says most new parts were fitted to FS 250 from production start, with unspecified exceptions; this is not blanket FS 250 fitment approval. Shared sheets do not extend the named model/configuration scope. Factory availability is historical, not current stock. No physical interchange test was performed.
Source: TI 22/2001, p. 1 · TI 22/2001, p. 2 — 1 update context;2 complete drawing, table and remarks.
Part numbers (6)
- 4134 710 7103 — Previous drive tubePrevious · FS 350; stated configuration only
- 4134 710 7106 — Steel-sleeved drive tubeNew · FS 350; stated configuration only
- 4134 711 7300 — Previous longer flexible linerRemains spare · FS 350; stated configuration only
- 4134 711 7302 — Shorter flexible linerNew · FS 350; stated configuration only
- 4134 711 2100 — Drive-tube plugUnchanged number; one instead of two · FS 350; stated configuration only
- 0000 967 3684 — Instruction labelUnchanged · FS 350; stated configuration only
Conditional replacement · FS 350
FS 350: new cylinder shroud requires clutch-housing cover
Stronger clamp neck and fasteners have their own serial; casting numbers conflict in the source.
1 50 396 511 — From this serial for FS 350 clutch housing only. Cover introduction remains in progress; this is not a cover cutoff or whole-model production range.
- Seal the clutch-housing recess with cover 4134 161 1200 when a new cylinder shroud is installed on a previous FS 350. This cooling-air requirement is separate from strengthened clamp-neck introduction.
- Clutch housing order number 4134 160 0603 is unchanged and includes clamp fasteners. IS-D5x24 screw 9075 478 4159 is replaced by IS-D6x32 9075 478 4718 and A6.4 washer 9291 021 0140. Only modified housing is factory supplied; previous screw remains a spare.
- Serial 1 50 396 511 applies to the clutch housing ONLY. Cover introduction refers to section5.3 (in progress), so this is not a documented cover cutoff. Summary lists cover separately as item5, outside housing inclusion items2–4.
- Unresolved casting-number conflict: illustration prints 4134 161 0565 B, prose prints 4134 121 0565 B. Both source readings are retained; do not silently choose one as the verified identifier. Neither casting number is the unchanged housing order number.
- TI22 describes an interdependent update package. Its introduction says most new parts were fitted to FS 250 from production start, with unspecified exceptions; this is not blanket FS 250 fitment approval. Shared sheets do not extend the named model/configuration scope. Factory availability is historical, not current stock. No physical interchange test was performed.
Source: TI 22/2001, p. 11 — 10 full drawing, prose, service note and summary.
Part numbers (7)
- 4134 160 0603 — Clutch housingUnchanged order number; stronger neck · FS 350; stated configuration only
- 9075 478 4159 — IS-D5x24 clamp screwPrevious; remains spare · FS 350; stated configuration only
- 9075 478 4718 — IS-D6x32 clamp screwNew stronger clamp · FS 350; stated configuration only
- 9291 021 0140 — A 6.4 washerNew clamp washer · FS 350; stated configuration only
- 4134 161 1200 — Clutch-housing coverRequired with new cylinder shroud · FS 350; stated configuration only
- 4134 161 0565 — Casting identifier in illustrationConflicts with prose; not order number · FS 350; stated configuration only
- 4134 121 0565 — Casting identifier in proseConflicts with illustration; not order number · FS 350; stated configuration only
Service note · FS 120 / FS 200 / FS 350 / FS 400 / FS 450
FS120/200/350/400/450: clutch and rigid-shaft construction
Two unlined clutch shoes;4,300 rpm engagement is not idle or cut-off speed.
- Clutch uses TWO LARGE-DIAMETER SHOES WITHOUT LININGS. The rigid drive shaft is supported in a FULL-LENGTH LINER. Neither description supplies part numbers, wear limits, lubrication intervals or a shaft conversion.
- Every engine-table column gives clutch engagement at4,300 rpm. Do not confuse that value with2,800 rpm idle, electronic cut-off without a cutting tool, or the rated output-shaft speed. No field clutch test was performed.
- Historical TI42/1997 configurations only, not all later versions sharing a model name. No hardware operation was performed. No part interchange or numeric serial cutoff is established.
Source: TI 42/1997, p. 3 — Section1 clutch/shaft; section2.1.1 clutch row.
No additional parts-table entry added.
Wrong number or missing part for the FS 300, FS 350? Report a correction →