Stihl 4134 · Section J · 9 of 14 · 32 parts
Handlebar, Control handle
Fits FS 300, FS 350.
Historical fitment & changes (6) — includes parts and conditions not shown on this drawing.
Parts (32)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4128 790 1701 | Handlebar | 1 |
| 2 | 4128 791 0300 | Handle, left | 1 |
| 3 | 4128 790 0304 | Handle, right | 1 |
| 4 | 9074 478 3025 | Pan head self-tapping screw IS-P4x16 | 3 |
| 5 | 4128 182 1700 | Slide control | 1 |
| 6 | 4128 182 4201 | Detent spring Fitment / change note → | 1 |
| 7 | 4128 182 6200 | Collar screw | 1 |
| 8 | 4128 182 4502 | Torsion spring Fitment / change note → | 1 |
| 9 | 4128 182 4501 | Torsion spring | 1 |
| 10 | 4128 182 1000 | Throttle trigger | 1 |
| 11 | 4128 182 4504 | Torsion spring | 1 |
| 12 | 4128 182 4500 | Torsion spring | 1 |
| 13 | 4128 182 0800 | Lockout lever | 1 |
| 14 | 4128 793 3000 | Slide Fitment / change note → | 1 |
| 15 | 4128 791 3100 | Spring Fitment / change note → | 1 |
| 16 | 9214 320 0700 | Lock nut M5 | 1 |
| 17 | 9022 346 1070 | Spline screw IS-M5x30 | 1 |
| 18 | 9291 021 0120 | Washer 5.3 | 1 |
| 19 | 4128 180 1112 | Throttle cable | 1 |
| 20 | 4128 182 3203 | Throttle cable | 1 |
| 21 | 4134 182 2104 | Support, bottom | 1 |
| 22 | 4134 180 6702 | Support | 1 |
| 23 | 9075 478 4159 | Pan head self-tapping screw IS-D5x24 | 1 |
| 24 | 9291 021 0120 | Washer 5.3 | 1 |
| 25 | 4128 791 0900 | Clamp, top | 1 |
| 26 | 0000 997 1304 | Compression spring Fitment / change note → | 1 |
| 27 | 4128 791 0905 | Clamp, base | 1 |
| 28 | 4128 790 7501 | Tommy screw | 1 |
| 29 | 0000 997 1701 | Compression spring | 1 |
| 30 | 9291 021 0140 | Washer 6.4 | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 4128 790 1309 | Control handle | 1 |
| — | 4134 790 1351 NLA | Control handle | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · FS 120 / FS 200 / FS 250 / FS 350
TI09: bike-handle microswitch, spring and cable assembly
Ground wire goes in first; the trigger spring sits in front of the bent cable sleeve.
- Seat microswitch 7 in the molding as illustrated. Push ground wire 8 into channel 10 first, then short-circuit wire 9. Respect routing between channel and corrugated tube; the cited second illustration in 1.12.4 places both wires fully in the channel and in recess 20 at corrugated-tube attachment 19, with neither wire projecting.
- Press cable 11 into slide 12 until ferrule 13 snaps in. Place slide with its groove at the END of the slot as the basic adjustment position. Diagram 393TI047 shows the groove arrow; do not substitute a mid-slot position.
- Attach bent cable end sleeve 14 to trigger 15. For the bike handle, put the straight end of spring 16 in the trigger IN FRONT OF the bent sleeve; fit its ring over pivot 17 at the lower trigger end and its loop around screw boss 18. The loop-handle instruction instead puts the straight end UNDER the sleeve; keep these constructions distinct.
- Check corrugated tube and slide position. Do NOT squeeze the trigger until section 1.12.5. Screw moldings together without pinching wires, mount handle on handlebar, attach cable to carburetor or check its seating in the pin per 1.12.2, reassemble powerhead, secure cable to drive-tube retainers, then set and secure handlebar in working position before adjustment. Pin selection and retrofit prerequisites remain separate unresolved work; no universal pin is inferred.
- Only the stated TI09 model and handle configurations with the new two-wire microswitch/cable and slide adjuster are covered. Shared sheets do not extend this to FS 300, BT 121 or other unnamed variants. This assembly/adjustment note is not a complete older-machine conversion; TI22/2001 and the remaining control roster and retrofit dependencies are still actionable. No physical interchange test was performed.
Source: TI 9/2003, p. 9 · TI 9/2003, p. 10 · TI 9/2003, p. 11 — 1.12.3 bike-handle assembly;1.12.4 wire-routing cross-reference;1.12.5 adjustment prerequisite.
No additional parts-table entry added.
Service note · FS 120 / FS 200 / FS 250 / FS 350 / FS 120 R / FS 200 R / FS 250 R / BT 120 C
TI09: slide-adjuster reset and fully assembled-machine adjustment
Reset to the end of the slot, then operate interlock and full trigger travel once assembled.
- Adjust only with machine COMPLETELY and securely assembled and handlebar/control handle in NORMAL OPERATING position. This removes cable free play and is required for correct full-throttle, starting-throttle and idle operation. A transport-position setting is not equivalent.
- Readjust after accidental early trigger squeezing during handling or installation; after servicing or repair; before readjusting carburetor; during new-machine setup; after a large bike-handle position change such as transport versus operating position; or after cable stretch or a slide position change from snagging during operation. Do not reduce this list to a one-time factory adjustment.
- Use screwdriver to press down slide 12 and push it to the END of the slot, the basic setting shown by diagram 393TI054. Then press trigger interlock 21 and squeeze trigger 15 fully: slide 12 moves away from the end position and cable adjusts automatically. Adjust carburetor if necessary. The source does not instruct starting the engine to perform this reset and supplies no cable free-play dimension.
- The handle-assembly pages warn not to squeeze the trigger earlier. Follow the bike- or loop-handle assembly instructions and cable/pin seating prerequisites before this adjustment; automatic adjustment does not prove safe mechanical interchange.
- Only the stated TI09 model and handle configurations with the new two-wire microswitch/cable and slide adjuster are covered. Shared sheets do not extend this to FS 300, BT 121 or other unnamed variants. This assembly/adjustment note is not a complete older-machine conversion; TI22/2001 and the remaining control roster and retrofit dependencies are still actionable. No physical interchange test was performed.
Source: TI 9/2003, p. 6 · TI 9/2003, p. 11 — 1.12.5 all-model slide adjustment with1.10 explicit loop-handle scope.
No additional parts-table entry added.
Service note · FS 120 / FS 200 / FS 250 / FS 350 / FS 120 R / FS 200 R / FS 250 R / BT 120 C
TI 09: new control handles use a sealed switch and cable adjuster
The slide-slot identifies the new handle; cable and handle remain separate replacement assemblies.
- The new package covers control handle, throttle cable, retainer, retainer-to-ignition short-circuit wire, carburetor housing, contact plate/gasket changes and carburetor cable pin. The new carburetor is introduced concurrently. New versions may ONLY be installed as a complete matched assembly in previous machines, not as arbitrary individual substitutions. The required pin depends on the existing carburetor/cable combination.
- Control handle and throttle-cable assembly are supplied separately. The cable assembly consists of corrugated hose, cable, and sealed microswitch permanently connected to two fully insulated short-circuit wires running to retainer connectors. New cables install only as assemblies; do not invent separate microswitch/cable order numbers.
- New control handles have a semi-automatic adjuster identified by the slide slot (1); grey areas in drawing393TI042 are non-slip surfaces, not extra parts. Slide control (2) operates the sealed ignition microswitch. Bike and loop handles are distinct despite this shared design.
- At the prescribed adjustment, one FULL trigger squeeze removes slack between trigger and carburetor cable attachment points. The sheath end is attached to slide (1); it pulls toward the trigger while spring-loaded detent arm moves along the notched track until free play is removed. This describes the mechanism, not permission to actuate before assembly: follow the already reviewed section 1.12.5 procedure only after complete assembly and operating-position setup.
- Adjustment is needed after first-time handle/cable installation and may be needed during new-machine setup, especially after bike handlebars are fitted. Section 1.12.5 governs later readjustments; the adjustment chapter is added to the user instruction manual.
- USA production introduction is in progress, without a numeric cutoff. Factory availability describes the bulletin date, not current stock. Shared catalog sheets do not extend the stated model/handle/configuration scope. No physical interchange test was performed.
Source: TI 9/2003, p. 1 · TI 9/2003, p. 2 · TI 9/2003, p. 3 · TI 9/2003, p. 7 — 1 introduction/interchangeability;1.1–1.2.2;1.10 introduction.
No additional parts-table entry added.
Conditional replacement · FS 120 / FS 200 / FS 250 / FS 350
TI 09: bike-handle control replacement and spring roster
FS 120/200/250/350 bike controls retain older spares; new handle excludes the cable assembly.
- For BIKE-HANDLED FS 120/200/250/350, control handle 4128 790 1300 becomes 4128 790 1301. Old handle includes items 13–16; new includes13, 14, 17–19. Right handle 4128 790 0300 becomes 4128 790 0301; detent spring 4128 182 4200 becomes 4128 182 4201.
- Contact springs 4128 442 1600 and 4128 442 1605 are removed from the new handle. Added components are torsion spring 4128 182 4502, slide 4128 793 3000 and spring 4128 791 3100. Every previous part marked remark 1 remains available as an older-machine spare; all other parts remain as before.
- The control-handle contents do NOT include throttle-cable assembly 4128 180 1104, which is separately supplied. This roster is not loop-handle fitment and does not transfer FS 250-only rotating-handlebar support permission to the other models.
- USA production introduction is in progress, without a numeric cutoff. Factory availability describes the bulletin date, not current stock. Shared catalog sheets do not extend the stated model/handle/configuration scope. No physical interchange test was performed.
Source: TI 9/2003, p. 2 · TI 9/2003, p. 5 · TI 9/2003, p. 6 · TI 9/2003, p. 7 — 1.1;1.10 items11–25 with remarks.
Part numbers (11)
- 4128 790 1300 — Old complete bike control handleOlder-machine spare · FS 120, FS 200, FS 250, FS 350; stated configuration only
- 4128 790 1301 — New bike control handleIncludes items 13, 14, 17–19 · FS 120, FS 200, FS 250, FS 350; stated configuration only
- 4128 790 0300 — Old right handleOlder-machine spare · FS 120, FS 200, FS 250, FS 350; stated configuration only
- 4128 790 0301 — New right handleNew · FS 120, FS 200, FS 250, FS 350; stated configuration only
- 4128 182 4200 — Old detent springOlder-machine spare · FS 120, FS 200, FS 250, FS 350; stated configuration only
- 4128 182 4201 — New detent springNew · FS 120, FS 200, FS 250, FS 350; stated configuration only
- 4128 442 1600 — Old contact springOlder-machine spare; deleted from new · FS 120, FS 200, FS 250, FS 350; stated configuration only
- 4128 442 1605 — Old contact springOlder-machine spare; deleted from new · FS 120, FS 200, FS 250, FS 350; stated configuration only
- 4128 182 4502 — Torsion springNew · FS 120, FS 200, FS 250, FS 350; stated configuration only
- 4128 793 3000 — Adjuster slideNew · FS 120, FS 200, FS 250, FS 350; stated configuration only
- 4128 791 3100 — Adjuster springNew · FS 120, FS 200, FS 250, FS 350; stated configuration only
Conditional replacement · FS 120 / FS 200 / FS 250 / FS 350 / FS 120 R / FS 200 R / FS 250 R / BT 120 C
TI 09: cable assemblies keep distinct 690, 185 and 545 mm hoses
The spare-hose remarks contain broken item references; no collar screw is treated as hose.
- BIKE-HANDLED FS 120/200/250/350: cable assembly 4128 180 1102 (items 22, 24) becomes 4128 180 1104 (items 22–24) with 690 mm hose. LOOP-HANDLED FS 120 R/200R/250R: 4134 180 1107 (items 40, 42) becomes 4134 180 1103 (items 40–42) with 185 mm hose. BT 120 C: 4313 180 1100 (items 47, 49) becomes 4313 180 1102 (items 47–49) with 545 mm hose.
- Each new assembly adds microswitch with short-circuit wires. Previous assemblies remain older-machine spares. Individual old cable/hose components were not supplied separately (remark 2); new individual cable, microswitch/wires and cut hose are not supplied separately (remark 3). Asterisks are non-orderable placeholders, not part numbers. The separately identified spare hose is the explicit cutting-stock exception.
- Item 25 names960 mm spare hose 4203 711 7201, with a dash in the New column; remark 5 nevertheless says to use it instead of the hoses in items 24, 42, 49 and57. The690/185/545 mm lengths belong to the three named assemblies, NOT to a single interchangeable complete cable.
- Documented source error: remark 4 says cut from spare hose at items 25 OR50, but item 50 is a COLLAR SCREW. Remark 5 also refers to item 57, which does not exist in this section (ends at50). Item 25 is the named spare hose; do not fabricate another hose number or an item 57 application. Preserve the erroneous references, without treating screw 0000 711 8700 as cutting stock.
- USA production introduction is in progress, without a numeric cutoff. Factory availability describes the bulletin date, not current stock. Shared catalog sheets do not extend the stated model/handle/configuration scope. No physical interchange test was performed.
Source: TI 9/2003, p. 2 · TI 9/2003, p. 6 · TI 9/2003, p. 7 — 1.2;1.10 items20–25,38–42,45–50 and all remarks.
Part numbers (7)
- 4128 180 1102 — Throttle-cable assemblyPrevious; older-machine spare · FS 120/200/250/350; bike handle
- 4128 180 1104 — Throttle-cable assemblyNew; includes microswitch/wires · FS 120/200/250/350; bike handle
- 4134 180 1107 — Throttle-cable assemblyPrevious; older-machine spare · FS 120 R/200R/250R; loop handle
- 4134 180 1103 — Throttle-cable assemblyNew; includes microswitch/wires · FS 120 R/200R/250R; loop handle
- 4313 180 1100 — Throttle-cable assemblyPrevious; older-machine spare · BT 120 C only
- 4313 180 1102 — Throttle-cable assemblyNew; includes microswitch/wires · BT 120 C only
- 4203 711 7201 — 960 mm spare hoseCut to specified assembly length; broken cross-references retained · FS 120, FS 200, FS 250, FS 350, FS 120 R, FS 200 R, FS 250 R, BT 120 C; stated configuration only
Historical fitment · FS 300 / FS 350 / FS 400 / FS 450
FS 300 / 350 / 400 / 450: handlebar clamp spring change
Spring 1304 replaces 1302 between the two clamp moldings; introduction remains in progress.
- Section 2 and figure 255TI003 KN locate the helical spring BETWEEN THE TWO MOLDINGS of the handlebar clamp. Original 0000 997 1302 will be replaced by 0000 997 1304. Figure item 1 is this spring, not the separate spring associated with the tommy screw.
- Introduction is IN PROGRESS, with no serial or date boundary. The original spring remains available FOR OTHER MODELS (remark 1). No other models are named and no blanket spring interchange, new clamp molding or combined conversion kit is specified.
- Later FS 300/350 J and FS 400/450/480 O sheets list 0000 997 1304 as a compression spring, at positions 26 and 9 respectively. Their separate spring 0000 997 1701 is not this replacement. Catalog positions differ from TI figure item 1. FS 480 is not admitted from the shared sheet.
- Historical source guidance; no present-day stock guarantee or verified physical interchange. No hardware operation was performed.
Source: TI 20/1998, p. 2 — Page 2 complete section 2, handlebar figure, summary and remark.
Part numbers (2)
- 0000 997 1302 — Original helical springRetained for other models · Handlebar clamp between moldings; named FS models only
- 0000 997 1304 — New helical springReplaces original; introduction in progress · Handlebar clamp between moldings; named FS models only
Wrong number or missing part for the FS 300, FS 350? Report a correction →