Stihl 4135 · Section J · 9 of 15 · 31 parts
Support frame
Fits FR 108.
Historical fitment & changes (4) — includes parts and conditions not shown on this drawing.
Parts (31)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4135 790 6800 | Support frame | 1 |
| 2 | 4132 701 1800 | Backplate | 1 |
| 3 | 4132 791 7400 | Strap | 2 |
| 4 | 9022 341 0950 | Spline screw IS-M5x10 | 6 |
| 5 | 4132 790 5400 | Support with loop | 2 |
| 6 | 4132 791 1000 | Bearing housing | 1 |
| 7 | 9503 003 6560 | Grooved ball bearing 6202-2Z | 1 |
| 8 | 9022 341 1260 | Spline screw IS-M6x12 | 5 |
| 9 | 4135 792 4500 | Engine mounting | 1 |
| 10 | 9321 630 0200 | Spring washer 10 | 1 |
| 11 | 9291 021 0200 | Washer 10.5 | 1 |
| 12 | 9008 319 2360 | Hexagon head screw M10x20 | 1 |
| 13 | 4132 790 9300 | Rubber buffer | 3 |
| 14 | 9321 630 0140 | Spring washer 6 | 6 |
| 15 | 9210 319 0900 | Hexagon nut M6 | 6 |
| 16 | 4135 791 5405 | Support | 1 |
| 17 | 9022 341 0980 | Spline screw IS-M5x16 | 2 |
| 18 | 4135 791 5400 | Support | 1 |
| 19 | 9022 341 0960 | Spline screw IS-M5x12 → replaced by 9022 341 0980 TI 3/2006 | 2 |
| 20 | 4132 718 6100 | Shackle | 1 |
| 21 | 4132 710 6100 | Shoulder pad | 2 |
| 22 | 4203 792 7200 | Slide | 2 |
| 23 | not sold separately | Strap 25x80 mm / 1x3.1'' not available as a separate item | 2 |
| 24 | 9408 021 4530 | Rivet shank 4x8x6 | 4 |
| 25 | 9409 021 4420 | Rivet head 4x8 | 4 |
| 26 | not sold separately | Strap 25x710 mm / 1x28'' not available as a separate item | 2 |
| 27 | 4132 718 7800 | Loop | 1 |
| 28 | 9291 021 0140 | Washer 6.4 | 1 |
| 29 | not sold separately | Strap 38x170 mm / 1.5x6.7'' not available as a separate item | 2 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 0000 930 2241 | Webbing 25 mm x 10 m / 1'' x 33' not illustratedoption | 1 |
| — | 0000 930 2242 | Webbing 38 mm x 5 m / 1.5x197'' not illustratedoption | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · FR 108
FR 108: pivot mounting, controls and drive geometry
Flexible connection and six-bushing rigid drive are distinct; tool mounting is M 10 x 1 left-hand thread.
- Handle adjusts along the shaft for operating position. Anti-vibration elements lie between engine and support frame; pivot-mounted engine follows drive-tube movements to reduce loads on the flexible drive shaft. Source describes AV system and controls as on FR 106, without establishing all-part interchange.
- Control illustration 360 TI 002: throttle trigger lock (4), throttle trigger (5), slide control (6). Starting throttle, run and stop positions are selected one-handed. Claimed handling, safety and fatigue benefits are source descriptions, not independently measured results.
- Clutch has lined shoes pivot-mounted on the flywheel. Rigid drive shaft is supported by SIX bushings; do not confuse it with the flexible engine connection. Gearhead is described as same as FS 66 through 108 and FR 106, but the TI supplies no universal parts substitution roster for that range.
- Cutting-tool mounting (page 4 key 7) is M 10 x 1 LEFT-HAND thread, described as on FS 74,76,86,88,106,108 and FR 106. Gearhead is a helical bevel drive with printed ratio 1.33. Source lists engine speed 12,000 rpm separately from maximum output-shaft/tool-mounting speed 9,000 rpm; they are not interchangeable limits.
- Historical TI 04/1995 guidance for the FR 108, series 4135; no serial cutoff is printed. Historical approvals and specifications are not a current compatibility approval or independently measured performance. Exact-model IPL links are navigation, not permission to apply these values to an unidentified later configuration. No hardware operation was performed.
Source: TI 4/1995, p. 1 · TI 4/1995, p. 3 · TI 4/1995, p. 4 · TI 4/1995, p. 5 — pivot mounting, controls and drive geometry.
No additional parts-table entry added.
Service note · FR 108
FR 108: handle, drive and support-frame torques
Gearhead clamps print 8.0 Nm without an imperial value; M4/M5 defaults do not override specific rows.
- All pairs are printed Nm / lbf.ft; spline screws unless otherwise named. Shroud, IS-M 5x12: 5.5 / 4.0. Two halves of control handle, IS-P 4x19: 2.0 / 1.5. Guard to handle molding, IS-P 4x35: 2.0 / 1.5. Clamp on control handle, IS-M 5x16: 3.5 / 2.6.
- Clamp screw in drive-tube sleeve, IS-M 6x25: 7.0 / 5.2. Setscrew in drive-tube sleeve, IS-M 5x10: 3.5 / 2.6. Clamp screws in gearhead, IS-M 5x20: 8.0 Nm; imperial cell is BLANK in the scan, not zero or a printed conversion.
- Bracket to support frame, IS-M 5x10: 3.5 / 2.6. Clamp to support frame, IS-M 5x10: 3.5 / 2.6. Bearing housing to support frame, IS-M 6x12: 10.0 / 7.4. Shackle to support frame, IS-M 6x12: 7.0 / 5.2. Rubber buffer, hexagon nut M6: 5.0 / 3.7.
- Engine mounting, hex-head M10x20: 30.0 / 22.0. Clamp for loop handle AND strain relief cord, IS-M 6x12: 6.0 / 4.4. Grease filler opening in gearhead, screw plug IS-M 11x10: 10.0 / 7.4.
- Screws/nuts M4, ALL OTHERS: 2.5 / 1.8. Screws/nuts M5, ALL OTHERS: 4.5 / 3.3. These residual rows are not universal torque values and do not replace listed component values or the two explicit unspecified tensioner rows. No sequence or complete installation procedure is provided.
- Historical TI 04/1995 guidance for FR 108, series 4135; no serial cutoff is printed. Exact-model IPL links are navigation, not proof of interchange or permission to use these values on an unidentified later configuration. No hardware operation was performed.
Source: TI 4/1995, p. 8 — handle, drive and support-frame torques.
No additional parts-table entry added.
Service note · FR 108
FR 108: workshop-tool roster and three explicit alternatives
Flange, air-gap gauge and circlip-plier alternatives stay conditional; signal-equipped wrenches are distinct.
- 1113 850 4200 — Test flange: leakage test; 1128 850 4200 — Alternative test flange: footnote 1 alternative to 1113 850 4200; 1111 890 6400 — Setting gauge: ignition module/flywheel air gap; 4118 890 6401 — Alternative setting gauge: footnote 2 alternative to 1111 890 6400; 0000 890 4400 — Puller: removing oil seals; 0000 893 3706 — Jaws profile 3.1: for oil-seal puller; 5910 890 2210 — Installing tool 10: hookless piston snap rings; 5910 893 5608 — Socket 13 mm: crankshaft nut: carrier/flywheel; 5910 890 0301 — Torque wrench: 0.5 to 18 Nm; 5910 890 0302 — Torque wrench: 0.5 to 18 Nm; optical/acoustical signal; 5910 890 0311 — Torque wrench: 6 to 80 Nm; 5910 890 0312 — Torque wrench: 6 to 80 Nm; optical/acoustical signal; 5910 893 8800 — Assembly hook: removing pickup body; 5910 890 2400 — T-handle screwdriver QI-T27x150: IS spline screws; 5910 890 8210 — Crimping tool: wire connectors and lugs; 5910 850 3100 — Assembly stand: holds powerhead for repair; 5910 893 2500 — Flange: assembly stand accessory; 5910 890 2100 — Clamping plate: settings as for FS 106 or FS 108; 0812 542 2104 — Socket: cylinder base screws; 4119 893 7200 — Press arbor: removing/installing main bearings; 0811 641 8380 — Pliers C19: INTERNAL gearhead circlips; 0816 630 1452 — C8 pliers: footnote 5 alternative to C19 pliers; 0811 611 8200 — Pliers A10: EXTERNAL circlips: clutch drum, gearhead, drive pinion; 0816 610 1495 — Circlip pliers: EXTERNAL clutch-drum circlips; 1108 893 4700 — Press arbor: removing clutch drum; 1118 893 7200 — Press arbor: removing/installing ball bearing in clutch housing.
- Footnotes permit ONLY the stated alternatives: flange 1128 850 4200 for 1113 850 4200; gauge 4118 890 6401 for 1111 890 6400; C8 pliers 0816 630 1452 for C19 pliers 0811 641 8380. These are historical tool alternatives, not blanket machine-part interchange.
- Footnote 4, optical/acoustical signal, attaches to torque wrenches 5910 890 0302 and 5910 890 0312, not all four wrench identifiers. The two ranges are 0.5–18 Nm and 6–80 Nm respectively. Assembly-stand accessory settings are referenced as for FS 106 or FS 108; actual setup dimensions are not provided here.
- Removing tool 4119 890 4600 is separately documented with its MANDATORY modification drawing; it must not be treated as an unrestricted tool from this roster. Neither roster nor generic tool name supplies a complete repair procedure.
- Historical TI 04/1995 guidance for FR 108, series 4135; no serial cutoff is printed. Exact-model IPL links are navigation, not proof of interchange or permission to use these values on an unidentified later configuration. No hardware operation was performed.
Source: TI 4/1995, p. 10 — workshop-tool roster and three explicit alternatives.
Part numbers (26)
- 1113 850 4200 — Test flangeleakage test · FR 108; TI 04/1995 conditions
- 1128 850 4200 — Alternative test flangefootnote 1 alternative to 1113 850 4200 · FR 108; TI 04/1995 conditions
- 1111 890 6400 — Setting gaugeignition module/flywheel air gap · FR 108; TI 04/1995 conditions
- 4118 890 6401 — Alternative setting gaugefootnote 2 alternative to 1111 890 6400 · FR 108; TI 04/1995 conditions
- 0000 890 4400 — Pullerremoving oil seals · FR 108; TI 04/1995 conditions
- 0000 893 3706 — Jaws profile 3.1for oil-seal puller · FR 108; TI 04/1995 conditions
- 5910 890 2210 — Installing tool 10hookless piston snap rings · FR 108; TI 04/1995 conditions
- 5910 893 5608 — Socket 13 mmcrankshaft nut: carrier/flywheel · FR 108; TI 04/1995 conditions
- 5910 890 0301 — Torque wrench0.5 to 18 Nm · FR 108; TI 04/1995 conditions
- 5910 890 0302 — Torque wrench0.5 to 18 Nm; optical/acoustical signal · FR 108; TI 04/1995 conditions
- 5910 890 0311 — Torque wrench6 to 80 Nm · FR 108; TI 04/1995 conditions
- 5910 890 0312 — Torque wrench6 to 80 Nm; optical/acoustical signal · FR 108; TI 04/1995 conditions
- 5910 893 8800 — Assembly hookremoving pickup body · FR 108; TI 04/1995 conditions
- 5910 890 2400 — T-handle screwdriver QI-T27x150IS spline screws · FR 108; TI 04/1995 conditions
- 5910 890 8210 — Crimping toolwire connectors and lugs · FR 108; TI 04/1995 conditions
- 5910 850 3100 — Assembly standholds powerhead for repair · FR 108; TI 04/1995 conditions
- 5910 893 2500 — Flangeassembly stand accessory · FR 108; TI 04/1995 conditions
- 5910 890 2100 — Clamping platesettings as for FS 106 or FS 108 · FR 108; TI 04/1995 conditions
- 0812 542 2104 — Socketcylinder base screws · FR 108; TI 04/1995 conditions
- 4119 893 7200 — Press arborremoving/installing main bearings · FR 108; TI 04/1995 conditions
- 0811 641 8380 — Pliers C19INTERNAL gearhead circlips · FR 108; TI 04/1995 conditions
- 0816 630 1452 — C8 pliersfootnote 5 alternative to C19 pliers · FR 108; TI 04/1995 conditions
- 0811 611 8200 — Pliers A10EXTERNAL circlips: clutch drum, gearhead, drive pinion · FR 108; TI 04/1995 conditions
- 0816 610 1495 — Circlip pliersEXTERNAL clutch-drum circlips · FR 108; TI 04/1995 conditions
- 1108 893 4700 — Press arborremoving clutch drum · FR 108; TI 04/1995 conditions
- 1118 893 7200 — Press arborremoving/installing ball bearing in clutch housing · FR 108; TI 04/1995 conditions
Service note · FR 108
FR 108: twenty historical workshop repair times
Tenths of an hour, not clock-minute decimals; trained staff and an equipped workshop are prerequisites.
- Table header explicitly names FS 88, FS 108 and FR 108. All values are HOURS expressed in tenths: 0.1 hour = 6 minutes. Values assume trained personnel in a properly equipped service workshop; they are historical labor allowances, not guaranteed owner repair durations, prices or mandatory service intervals.
- 1 Crankcase, Short Block: 2.1 h; 2 Crankshaft and/or Bearings: 2.2 h; 3 Crankcase Gasket, Sealing: 2.0 h; 4 Crankshaft seals: 0.7 h; 5 Cylinder and/or Piston: 0.8 h; 6 Ignition: 0.5 h; 7 Fuel Hose, Fuel Supply: 0.5 h; 8 Gear Box, Arbor Assy: 0.6 h; 9 Carburetor: 0.7 h; 10 Fan Housing, Clutch Housing: 0.8 h; 11 Front Handle, Throttle: 0.6 h; 12 Recoil Starter: 0.5 h; 13 Clutch: 0.5 h; 14 Drive Tube, Drive Shaft: 0.5 h; 15 Muffler: 0.4 h; 16 Air Filter, Filter Cover: 0.3 h; 17 Stop Switch: 0.4 h; 18 Fuel Tank: 0.4 h; 19 Replace Arbor Gears: 0.8 h; 20 Misc. Repairs: 0.5 h.
- The TI says this table for the new brushcutters can be added to the STIHL repair-times table. The cut-out border/scissors mark is a layout aid, not another repair instruction. Model names in this table do not establish parts interchange or authorize extending the FR 108 torque table to FS models.
- Historical TI 04/1995 guidance for FR 108, series 4135; no serial cutoff is printed. Exact-model IPL links are navigation, not proof of interchange or permission to use these values on an unidentified later configuration. No hardware operation was performed.
Source: TI 4/1995, p. 11 — twenty historical workshop repair times.
No additional parts-table entry added.
Wrong number or missing part for the FR 108? Report a correction →